• Connecting the router tr link. Step-by-step instructions for connecting and setting up a TP-Link router. Connecting and setting up a TP-Link router

    Good afternoon.

    In today's regular article on setting up a home Wi-Fi router, I would like to focus on TP-Link (300M Wireless N Router TL-WR841N/TL-WR841ND).

    Quite a lot of questions are asked about TP-Link routers, although in general, the setup is not much different from many other routers of this type. So, let's look at what you need to do step by step to ensure that both the Internet and the local Wi-Fi network work for you.

    1. Connecting a router: features

    There are several outputs on the back wall of the router; we are most interested in LAN1-LAN4 (they are yellow in the picture below) and INTRNET/WAN (blue).

    So, using a cable (see picture below, white) we connect one of the LAN outputs of the router to the computer’s network card. Connect the Internet provider cable that enters your apartment from the entrance to the WAN output.

    That's all. Yes, by the way, after turning on the device, you should notice the LEDs blinking + a local network should appear on the computer, without access to the Internet for now (we haven’t set it up yet).

    Now you need go to settings router. To do this, in any browser, type in the address bar: 192.168.1.1.

    Then enter the password and login: admin. In general, in order not to repeat myself, here is a detailed article about that, by the way, all the typical questions are discussed there.

    2. Setting up the router

    In our example, we use the PPPoE connection type. Which type you choose depends on your provider; all information on logins and passwords, connection types, IP, DNS, etc. should be in the contract. We now include this information in the settings.

    2.1. Setting up the Internet (PPPoE type)

    In the left column, select the Network section, WAN tab. Three points are key here:

    1) WAN Connection Type - indicate the type of connection. It will determine what data you will need to enter to connect to the network. In our case, PPPoE/Russia PPPoE.

    2) Username, Password - enter your login and password to access the Internet via PPPoE.

    3) Set the Connect Automatically mode - this will allow your router to automatically connect to the Internet. There are also manual connection modes (inconvenient).

    That’s it, the Internet is configured, click the Save button.

    2.2. Setting up a wireless Wi-Fi network

    To set up a wireless Wi-Fi network, go to the Wireless settings section, then open the Wireless Settings tab.

    Here you also need to pay attention to three key parameters:

    1) SSID - the name of your wireless network. You can enter any name, the one that will be convenient for you to search for later. The default is “tp-link”, you can leave it like that.

    2) Region - choose Russia (or your own, if someone is reading the blog not from Russia). This setting is not found in all routers, by the way.

    3) Check the boxes at the very bottom of the window, opposite Enable Wireless Router Radio, Enable SSID Broadcast (thereby you enable the Wi-Fi network).

    Save the settings, the Wi-Fi network should start working. By the way, I recommend protecting it with a password. More on this below.

    2.3. Enabling a password for a Wi-Fi network

    To protect your Wi-Fi network with a password, go to the Wireless section, Wireless Security tab.

    At the very bottom of the page there is an option to select the WPA-PSK/WPA2-PSK mode - select it. And then enter the password (PSK Password) that will be used every time you connect to your wireless network.

    Then save the settings and reboot the router (you can simply turn off the power for 10-20 seconds).

    Important! Some ISPs log the MAC addresses of your network card. Thus, if your MAC address changes, the Internet may become unavailable to you. When you change the network card or when installing a router, this address changes. There are two ways:

    first- this (I will not repeat here, everything is described in detail in the article; TP-Link routers have a special section for cloning: Network->Mac Clone);

    second- register your new MAC address with your provider (most likely a phone call to technical support will be enough).

    That's all. Good luck!

    Hello! The topic today will be a little strange, but what can you do? As they ask, I answer. You can't please everyone, but you have to think about something.

    Guys, this is a general article about setting up all router modelsTP- Link. I highly recommend that you search on our website for settings for your specific model - you will save both time and nerves. It’s better to download the manual from the official website - there is much more information there.

    Another request - if you haven’t found any point, you still have questions, or have corrections - leave comments. I have had many routers TP-Link, let's come up with something together.

    Customization goals

    The main task of an ordinary home router (and TP-Link is one of the leaders in this market, so their models can be seen in half of their neighbors) is to please the owner. What does the owner need:

    • 24/7 internet via Wi-Fi.
    • A working local network (less often, but some people drop files, use a printer, and watch movies on TV).
    • Other rare functions - everyone has their own thoughts, an individual approach is needed here, with this it is better to immediately comment.

    In total, we need to connect the Internet during this manul, and the local network will configure itself. In fact, there will be nothing complicated, and the generality of the topic will not greatly affect - all routers are configured almost identically for basic functionality. TP-Link is no exception - I tried a lot of them. So watch, do, think about it, but if you have any difficulties, look for instructions for your model from us.

    Setup video

    TP-Link TL-WR841

    This is the most popular router today of all the “tiplinks”. And of course we have separate instructions for it. All owners go to the page below:

    Before setting up

    We will need:

    1. Router
    2. Cable connecting the router to the power supply
    3. Network cable connecting from router to computer/laptop
    4. Internet provider cable in the apartment (Ethernet or ADSL)
    5. A computer or laptop with the ability to connect via wire (you can, of course, use a smartphone or tablet, but some models don’t like that, which is what I asked you to look for for your model)
    6. Login and password for connecting to the Internet
    7. Login and password for connecting to the router

    A few clarifications. If everything is clear with the device itself, then you need to find your login and password for the Internet. Usually it goes straight into the contract. If not, contact your provider by phone or in person. Sometimes they will understand.

    Another problem is the data for connecting to the router for further configuration. Here you need to get:

    • Connection address
    • Login
    • Password

    Usually this is all located on a sticker under the router itself. Something like this:

    If suddenly there is no sticker, try these values:

    • Address: 168.0.1 or 192.168.1.1 or http://tplinklogin.net
    • Login: admin
    • Password: admin

    If during the setup process the values ​​do not match, then there is a possibility that someone else used the router (even if it is new). Just reset the settings and everything will be as it should (more about resetting below). Sometimes it is even better to reset the settings to default than to reconfigure.

    Installation and activation

    So, let's start assembling the structure. Make sure the router is turned on:

    1. We place the router in a convenient position - it’s enough to reach both the Internet cable and the computer/laptop. How to install the model depends on the device itself - you can put it, you can hang it. Routers are generally unpretentious things.
    2. If there are removable antennas, we install them.
    3. We connect it to power. Many TP links have an “Enable” button on the back - don’t forget to click on it. We look to see if the indicator lights are on (if any). If they are on fire, we continue.
    4. We connect our Internet channel - be it an Ethernet cable, a telephone cable, or even a USB 3G/4G modem - it depends on your needs and capabilities. As a rule, another light comes on when the cable or USB device is successfully connected. The most important thing is that the cable is connected to a separate WAN connector - it usually differs from other ports in color. Don't get confused.
    5. We wait about a minute - the procedure for identifying connections can sometimes take a long time, so there’s no shame in it. In the meantime, it’s thinking, read on.

    Indication


    More for your reference. Main indicators on the panel. May vary from model to model, but everything is approximately the same everywhere. Very useful to watch when you need to quickly analyze a problem.

    • Nutrition. There is a separate light bulb. Even if nothing is connected, Wi-Fi is not working, it will still light up when the power is on.
    • Internet. Active internet connection. Initially disabled. When connected it lights up, but during active use it usually flickers very quickly.
    • WAN(this includes an Ethernet connection, a telephone ADSL connection, and a USB modem) – shows the presence of the connection itself (without the Internet). We connected the provider's wire - it caught fire. Sometimes combined with the previous lamp. For example, in ADSL it initially blinked when the line was established, and after connecting it simply glowed. But if it doesn’t light up, then you need to look at the wire.
    • Wi-Fi– usually enabled initially, but can be disabled in the settings. If there is a wireless network, it will light/flicker/blink.
    • WPS. Establishing a quick connection using a key. Usually starts blinking when you press a special button on a device with WPS. Available almost everywhere, but may be absent.
    • Network ports. Also common lamps - on the back there are LAN ports for connecting wired devices to the router. So, when connected, the corresponding indicator immediately lights up. Usually there are about 4 ports, and the same number of lamps.
    • USB. Likewise, if connected, it lights up. There may be other lamps, just look at the model. And something may be missing.

    Connecting a TP-Link router


    You can try to do the setup from a PC, a laptop, a tablet or a phone. Another question is that the Wi-Fi network will not always be available, so the classic option is to set up via wire. But the whole point here is in the connection. All other actions are the same. So I propose to consider further connecting via a laptop - there you can use both Wi-Fi and a wire.

    • Wire. Everything is simple with the wire. We connect it and see that the indicator light comes on. Did it catch fire? Then everything is ok. I won’t describe all the problems; sometimes you may need to reset the operating system’s network settings. Or maybe something more interesting. So feel free to write your questions and experiences in the comments. From my notes, it is important to connect the wire to the LAN connector. Do not confuse it with the WAN - the provider's cable goes there, if you confuse it, you will not be able to connect.


    • Wi-Fi. There is nothing complicated either. We search the networks for a network with a name something like TP-Link with the best signal and connect to it over the air. The default password is usually empty, or is specified in the settings on the same sticker. There were times when it was impossible to connect at all. But the whole point was that the neighbors also had a TipiLink, and even a more powerful connection) In general, you won’t miss it.

    Authorization in the web interface panel

    It's time to try going to the settings panel. To do this, go to the address recognized above, enter your username and password.


    If suddenly the password does not work, reset the device to factory settings. On the back of the panel there is usually a Reset recess with a button inside. We hold it in the on state with a needle for 10 seconds and try to connect again - everything should work out.


    There is usually nothing special about your personal account on the main page. Just general information:


    Unlike the screenshot above, when turned on for the first time, the IP address values ​​will be zero: 0.0.0.0. The figure already shows a successful connection establishment.

    ADSL, Ethernet, USB

    Once again, I repeat that all routers are built approximately the same. There is only a slight difference in the connection technology: via an ADSL telephone cable, via Ethernet, via a USB modem.

    Everywhere you will be required to enter a login and password from the provider. If you have any doubts, still find a review for your model. Here, for complete coverage, I will take an ADSL modem - there are a little more settings for the connection. So, if you use a modern cable, you will have fewer possible problems.

    It doesn't matter what operating system you use -WindowsLinuxMacOSiOSAndroid or something else. The setup will still take place through the browser on the web interface.

    Internet setup is easy

    Any modern modem is now equipped with a convenient setup wizard, and also in Russian. Now in my model it’s written like this – “Quick setup”. Everything is really shown and explained there in great detail, just for dummies. Therefore, I will not dwell on this extensively here, I will simply give step-by-step instructions on what he usually does:

    1. Greetings to you.
    2. It asks you to find out how you want to use the modem - set something like “Connect to the Internet”.
    3. It will ask how you want to do this - usually select PPPoE mode.
    4. Enter the login and password from your Internet provider.
    5. Usually here he asks about activating the Wi-Fi network. Asks you to create a password for her.

    Sometimes a special disk is supplied with the router. Usually there are no drivers on it, but a software setup wizard. The differences from the web interface are minimal.

    Setting up the Internet is difficult

    Everything is the same here - initially we are looking for either a quick setup, or Quick Setup, or Settings, or Configurations. It can be called differently. Here's an example:


    What is important to do here:

    • WAN Link Type – PPPoE – a common type for our networks, connection type.
    • VPI/VCI – 0/33. At Rostelecom I had 0/35. We are only talking about old telephone connections. This parameter was always included in the contract next to the login and password. The same difference and complexity compared to new networks.
    • PPP Username and PPP Password – login and password.

    Everything else isn't that important here. The names may vary slightly on your model. Especially if they are in Russian) But you get the gist. Do this, and the Internet will appear on the router. The indicator will signal this.

    Wi-Fi setup

    Usually the whole point of setting up WiFi comes down to turning it on and setting security parameters. Sometimes it all comes together on one page. The setup occurs either automatically from the wizard, or through the menu items Wi-Fi, Wireless, Wireless mode or something like that.

    Basic settings: WirelessBasic:


    What's important here:

    • EnableWireless– enable the wireless mode itself.
    • HideSSSIDBroadcast– hide the network from the list of networks. On the one hand, it’s cool that no one can find your network without third-party applications. On the other hand, when connecting all your devices, you will have to manually enter the name of the network - and this is not always convenient. And modern Wi-Fi security allows you to leave this option unused. I assure you, if someone wants to hack your network, this option will definitely not save you.
    • Wireless Network Name– network name. So it will be visible in the list of networks. Write something different from your neighbors)

    Attention! Changing the network name will reset your current Wi-Fi connection. You just need to reconnect manually.

    Now let's move on to Wi-Fi security: WirelessSecurity:


    Again on the safety points:

    • EnableWPS– set it to Disable if you do not use WPS. This is the ability to connect to a device without a password using the WPS function. Yes, there is a password there. But this password is searched faster than the password from WiFi itself. Modern models have all the necessary protection against overkill, but careful... If not necessary, turn it off.
    • NetworkAuthentication network authentication type. Determines the security level by specifying encryption. You need to choose - WPA2. And that's the only way.

    Do not useWEP – this system is very easy to hack!!!

    • WirelessNetworkKey– password for your network. Use at least 10 characters, do not use simple constructions, use letters and numbers. The more complex the better. This is your first line of defense.

    All. After saving, you can re-login to your network with a new password. This completes the basic settings. There is Internet, the network is active. You can use it. And this is how the setup works on any device.

    Nothing worked out? There are comments where you can ask your question. Just don't forget the name of your model and a detailed description of the problem!

    Panel access password

    Do you also remember that you connected to the panel using a standard password? Any person on the network can do the same and do something bad to you. The best method of protection is to change the password for our Wi-Fi router (not to be confused with the wireless network password):


    Advanced router settings

    Below I will give only a description of the possible functionality of routers. Options that are not used very often. Use it or not - only according to your needs. Experienced specialists usually figure things out on their own, but it would also be interesting to see such people in our discussion thread.

    It is better to clarify the settings below for a specific model.

    • Channel – can be set from 1 to 11. Usually there is an Auto mode. That's what we need. But if there is some kind of network load from neighbors or devices, you can try switching the channel, and suddenly the connection will improve. Use at your own risk.
    • Mode – protocol for working with Wi-Fi. Now there are b/g/n and b/g/n+ac. You can't go wrong with choosing more. All current standards are compatible.
    • Network bridge. Many routers allow operation in repeater (or repeater) mode. The essence comes down to intercepting a visible signal and repeating it with amplification. To reach the farthest room. Usually this setting is not visible, but it is present in many places. For me, it’s easier to purchase a separate repeater, but it’s more convenient for everyone.
    • Filtration – wide range to reject different devices. Typically, access is filtered by MAC address. But you can also filter access to the Internet by issued IP.


    Firmware

    Use in special cases. Usually everything works great out of the box. Only for those who know exactly what they are doing. Update plan:

    1. Download the firmware for your model from the official TP-Link website or a third-party forum with full confidence in compatibility.
    2. In the panel, go to “Software Update”. Select the downloaded file. Click “Update”.
    3. Installing new firmware takes up to 5 minutes - do not reboot the router during this operation - the device may be damaged.
    4. The device will most likely be rebooted.


    Hello! Very often they ask how to connect the router? So we bought a router, brought it home, and how to connect it, and what to do with it next, so that it would distribute the Internet via Wi-Fi and cable. In this article we will talk specifically about TP-Link routers. I'll tell you in detail and even take a photo on connecting TP-Link. Where and what cable to connect, how to connect the router to the provider, computer, modem, etc.

    In fact, there is nothing complicated about it. You just need a little time and patience :) After purchasing any router, in our case this is a TP-Link device, you will have to connect and configure it correctly. If you connect incorrectly, you will not be able to configure it. The setup process itself is a topic for another article, or for instructions on a specific model. Well, in this article we will analyze in detail the process of connecting a TP-Link router.

    The article is suitable for all models: TL-WR940N, TL-WR740N, TL-WR841N, TL-WR842ND, TL-WA701ND, TL-WR743ND, etc. I will show it using the TL-MR3220 as an example. I would like to show you how to connect (it's more popular), but now I only have the TL-MR3220 at hand. Well, okay, they are practically no different.

    Connecting a computer to TP-Link via a network cable

    First of all, we need to connect the power adapter to the router. Just plug it into the POWER connector. You definitely won’t miss there :) Well, plug it into the mains. If the indicators on the router do not light up, then check to see if it has a power button and is turned off.

    Further, if you configure (and/or use the Internet via cable) router from a computer? or laptop, then take the network cable that comes with the router and connect one end of the cable to your computer's network card, and the second to the LAN connector of the router. On TP-Link, LAN connectors are usually yellow and there are usually 4 of them.

    We connect the TP-Link router to the Internet provider or modem

    Everything is clear here. So that the router can distribute the Internet (and this is his main task), you need to connect to the Internet. Most likely, you have a regular network cable installed in your apartment, or your Internet is connected to an ADSL modem.

    We need to connect cable from the Internet provider to the WAN connector TP-Link router. The WAN connector is usually blue. Or, connect the cable from the modem to the WAN connector (for connection you can use the cable that comes with the router).

    This one looks something like this:

    That's all, the Internet is connected, and you can start setting up the router. Go to the settings of your TP-Link (see) and configure the router. You can set it up according to the instructions using the example. The setup will most likely be the same.

    It may also happen that immediately after connecting the router, the Internet will work on your computer and other devices that you connect. This is possible if your provider uses a Dynamic IP connection type, or you have a modem connection. In any case, you will need and.

    It seems like I haven't forgotten anything. As you can see, the instructions are simple and clear, anyone can connect. If something doesn’t work out, write in the comments, we’ll figure it out.

    Instructions

    In fact, all TP-Link models have similar parameters and connections, so this one will help you configure a TP-Link WiFi router under any number, for example, WR841n or WR740n. First, make sure that you have a configured wired DSL connection to the Internet (a network cord will be pulled into the apartment, and you have a login and password for the connection issued by your provider). Unpack the router: the kit must contain a short double power cord, a cable for connecting to an outlet and instructions.

    Plug the router into a power outlet and press the start button; the indicators on the front should light up. Connect your main DSL cable to the WAN connector of the router (usually it is located on the edge and highlighted with a blue or other frame). Connect the short power cord from the kit to any of the four LAN connectors at one end, and insert the other into the network connector of your computer or laptop.

    Now, to enter the device settings and configure the TP-Link WiFi router, open any installed Internet browser (for example, Internet Explorer), enter the address 192.168.0.1 or 192.168.1.1 in the address bar. You can find out which of them is working from the instructions included with your TP-Link router model. If none of the specified addresses are suitable (pressing Enter does not open anything), reset the current device settings by holding the Reset button for a few seconds (or inserting a needle into the corresponding hole, depending on the model). After entering the appropriate address in the browser, the router settings menu should open.

    Set up your router's main network connection. Go to the Network settings section and specify the type of your home network (for example, PPoE). You can look it up in the contract with the provider or call the support service. The provider must also provide information such as the presence of a dynamic or static IP address, server name, IP submasks and DNS. Enter your username and password for a wired Internet connection, select Connect Automatically and save the settings. Now, when you boot and have a connected router, your computer or laptop will automatically connect to the Internet.

    All that remains is to configure the TP-Link Wi-Fi router to have a home wireless connection to the network. Go to the Wireless section. Enter the desired Wi-Fi connection name and set any password convenient for you, saving the settings. Now try searching for available wireless connections or your smartphone. The connection you created should also be among those found. Select it, enter the password and check the functionality of the Internet by opening any site in the browser.

    In this article I will tell you how you can do the initial setup of Tp-link routers. The advantage of this company in terms of settings is that almost all Tp-link routers are configured almost the same way.

    In addition, they have an intuitive port color scheme. And even an inexperienced user will not have to think about where to connect which cable.

    We will configure the router in three stages:

    1. Setting up an Internet connection
    2. Setting up Wi-fi on the router

    So let's get started.

    Preparing the router for setup

    We turn on the router to the network. We connect the provider cable to the blue port on the router.

    If you do not have this cable, you can connect to the router via Wi-Fi from any device.

    Launch any browser and go to the site 196.168.0.1

    If this data is not suitable, then you can reset the settings on the router. To do this, press the Reset button and hold for 10 seconds. All indicators on the router should blink. After this, we wait about a minute until the router boots up and try to log in again.

    Setting up an Internet connection on a Tp Link router

    To set up the connection, we will need data from your provider. They should have been given to you upon connection. If this data is not available, you will need to call the support service and find out how to get it. It will also be possible to clarify the protocol by which you connect to the Internet (PPPoE, PPtP, L2TP, etc.) We will configure PPPoE, since this is the most common protocol used to connect to the Internet.

    • On the left in the menu, select the Network section (Netwotk)
    • Next, select the protocol you are connecting via (PPPoE, PPtp, L2Tp, etc.)
    • We enter the login and password issued by the provider (if you have a PPtP connection, you also need to specify the server address)
    • Secondary connection dot Dynamic IP
    • WAN connection mode, put a dot on Connect automatically
    • Click the Save button and wait for the page to refresh.

    After the page has been updated, open a new tab. If you did everything correctly, then the Internet should already be working. All that remains is to configure WiFi.

    Setting up Wifi on a Tp Link router

    Setting up Wifi couldn't be easier. If you have a dual-band router, then Wifi is configured separately for each 2.4 GHz and 5 GHz band!

    • On the left, select the Wireless network section
    • In the Network name (SSID) field, enter the name of the new Wifi network in Latin letters
    • Mode: 11bgn Mixed Channel: Auto
    • Click Save. If the router prompts you to reboot, then it’s too early.

    Now let's set a password for the Wifi network:

    • On the left, select the Wireless Security section
    • Select protection WPA/WPA2 – Personal or WPA-PSK/WPA2-PSK
    • We select the version WPA2-PSK, and the encryption is AES
    • Click Save

    If the router prompts you to reboot the router (a red line appears), then reboot. After the reboot, we check the WiFi connection, everything should work.

    Enjoy!

    Read more: