Getting ROOT and installing ClockworkMod recovery (CWM) on ZTE LEO Q1. Getting Root ZTE Leo Q1 Zte leo q1 firmware

• Block diagnostics of ZTE LEO Q1 phone

  During unit diagnostics, it is determined which specific element (Case, protective glass, sensor, printed circuit board, connectors, speakers, microphone, antenna, battery) has failed.

  Algorithm for block diagnostics of a phone:

  ZTE LEO Q1 phone does not charge; Checking h order, if the phone charge is intact, otherwise: Let's check if it's working: If all of the above does not suit you, then you will need or.
  ZTE LEO Q1 Won't turn on or boot; Checking n I'll lose charge, if the phone battery is charged then: We check and see if it’s correct power button on the phone; If at this stage we haven’t found the cause of the breakdown, remember - if the phone was filled with liquid, or the phone fell and stopped turning on, it will most likely be needed.
  ZTE LEO Q1 The phone does not connect to the network or does not see the SIM card; Checking whether the phone detects another SIM card, if it detects then: Checking phone settings, if the settings are correct then: Required.
  ZTE LEO Q1 Does not see the SD card, does not detect the flash drive; Checking phone flash card, if correct then: Checking flash drive connector on the phone, if it is also working, then: You need to either repair the phone's motherboard.
  ZTE LEO Q1 Does not charge via USB; Checking usb cable, if the cable is ok then: We check if it is ok then: You need or.
  ZTE LEO Q1 Not updated; Checking settings, if the settings are correct, then: Checking internet connection, if the connection is stable, then you need a phone.
  ZTE LEO Q1 Does not connect to Wifi; Checking phone settings, if the settings are correct then: Checking WiFi adapter telephone if ok required .
  ZTE LEO Q1 Does not see the computer; Checking connection cable to the computer if the cable is intact then: Checking drivers phone on the computer, if the correct drivers are installed, then: Phone required.
  ZTE LEO Q1 turns on, but there is no image on the screen or it is distorted on the phone: Checking for availability physical damage screen, if not then: Checking display cable phone, if the cable is intact, then: The phone needs repair or repair.
  The sensor on ZTE LEO Q1 stopped working: We check the integrity for damage, if it is intact then: Checking touch display cable, if intact then: Phone required, or controller repair display.
  The microphone does not work on ZTE LEO Q1; Checking phone settings, if the settings are correct then: We check if it is intact: Let's check if it works microphone controller on the phone if it works then: Required.

• Firmware for ZTE LEO Q1 phone

  Every year, phones perform more and more functions, and are already mini-computers. And for stable operation a well-functioning operating system is required.

  Phone firmware may be required for most problems - from the fact that the phone has stopped detecting the computer to the fact that the phone's display has stopped working.

  Cases when flashing a ZTE LEO Q1 smartphone is required:

  • Microphone doesn't work on ZTE LEO Q1;
  • The sensor on the ZTE LEO Q1 phone stopped working:
  • ZTE LEO Q1 phone turns on, but no image on screen or is it corrupted by the phone:
  • ZTE LEO Q1 does not see the computer;
  • ZTE LEO Q1 does not connect to Wifi;
  • ZTE LEO Q1 is not updated;
  • ZTE LEO Q1 won't turn on or does not load;
  • ZTE LEO Q1 phone does not receive network or doesn't see the SIM card;
  • ZTE LEO Q1 does not see the SD card, does not detect the flash drive;
  • ZTE LEO Q1 not charging via usb.

  In most cases, problems with the ZTE LEO Q1 phone arise due to the firmware or its incorrect update. Due to a glitch in the phone's firmware, the settings are lost, or the drivers of some controllers fail, and some functions may simply stop working.

• Component diagnostics of ZTE LEO Q1 phone

  Component Diagnostics of the ZTE LEO Q1 phone is a diagnostic of the phone's system board. This type diagnostics, being more complex, is the identification of damaged element on the board of the ZTE LEO Q1 phone. Repair device after this diagnostic involves resoldering the microcircuits and replacing faulty elements on the board of the ZTE LEO Q1 phone.

• Replacing the touch glass of a ZTE LEO Q1 phone

  Changing the protective glass of the ZTE LEO Q1 phone.

  The display of the ZTE LEO Q1 mobile phone is protected from damage by a special safety glass. If glass it will crack or chip as a result of a fall, then display your phone is at risk: it may also be damaged, and the image may become “blurry” or the LEO Q1 phone will stop displaying altogether. If dust or small debris gets behind the glass, it will further damage it. Our service center specialists can replace the protective glass of your ZTE LEO Q1 phone to prevent possible .

Download Zte Leo S1 PC Suite including USB Driver, ADB Driver, and Firmware for Windows XP, Windows Vista, Windows 7 and Windows 8. By downloading this driver, you will be able to connect your Zte Leo S1 to any computer or laptop. This software allows you to share data, modify files, and backup your phone's data, contacts, calendar and more. This PC Suite is easy to use and free.

Note that this PC Suite is for Windows only. It is not compatible with Linux OS or Macintosh OSX.

What can this PC Suite do with Zte Leo S1?

The PC Suite allows you to backup and restore contacts, messages, and calendar. It also enables copying/tranfering files, music, pictures, and video from your phone to your computer.

How to install this software:

1. Download the setup files and simply run them. Windows Vista and Windows 7 users need to run the setup files as administrator (Right click on the file and then "Run as administrator"). If you miss this step the driver might not install correctly.

2. Once the setup is done, connect your device (Zte Leo S1) to your computer via your USB port.

3. Wait a few moments for your computer to detect the device.

4. Congratulations! You have successfully installed your Zte Leo S1 driver and PC suite! Have fun! If you had any comments or questions about this guide, let us know.

Zte Leo S1 Product Review and Specs

Zte Leo S1 uses a card, and supports .

The display is a touchscreen that is .

Zte Leo S1 PC Suite

If you would like to connect your Zte Leo S1 to your computer, download the PC Suite for Zte Leo S1 here on SymptomDB. It is free, easy to use and setup and you can backup and restore your device with little effort. The PC suite and driver enables you to copy files and folders, backup messages (including chats), contacts, music, photos, videos and more.

Zte Leo S1 doesn't connect to PC

You need to download and install the USB drivers first, and then connect your device to your PC and install the driver when prompted. The PC Suite will not recognize your device unless the USB driver has been installed correctly beforehand.

Zte Leo S1 does not turn on

If your Zte Leo S1 does not turn on, follow these steps:

1. Make sure your device is charged. Let it charge for several minutes to ensure that it has enough power. It is best to plug directly into the wall, as it will usually charge faster than plugged into a computer"s USB port.

2. Hold in the power button for 30 seconds.

3. Remove the battery from your phone for 10 seconds, and then plug the battery back in.

Zte Leo S1 won't charge

If your Zte Leo S1 is not charging, you can try the following steps:

1. Restart your phone. Sometimes this can fix the issue, particularly in the case where the phone is not responsive when charging.

2. Try a different charging cable, or a different power source.

3. Try reseating the battery if it is easily accessible.

Take a screenshot with Zte Leo S1

On most devices, pressing the sleep/wake button and the volume down button simultaneously will take a screenshot. On devices with a Home button, holding the power button and home button at the same time will take a screenshot.

1. Download the latest version of the Framaroot application (as of 11/07/2013 it is 1.6.1) here - ().
2. We install the downloaded application.
3. Launch Framaroot on your ZTE LEO Q1.
4. Choose SuperSU.
5. We select the option for obtaining ROOT - Baromir.
6. We are waiting for the process of obtaining ROOT to complete.
7. Reboot the smartphone.

Installing ClockworkMod recovery (CWM) on ZTE LEO Q1

1. Remove the SIM card, but leave the SD card with enough free space. We connect LEO Q1 to the computer.

2. Select the “CD-Rom” connection mode and install the drivers.

3. Download, unpack and launch. On the phone we turn on debugging mode.

4. If the program has detected your phone, then go to the “root, backup, recovery” tab and first make a backup (root is required):

Check the box “Save userdata and cache”

Click the Backup button.

The window on the right will indicate the path where your backup is saved. If the program asks for permission to archive a backup, then we agree.

Then click on the “Prepare blocks for FlashTool” button.

All. The backup has been merged, copy it to a safe place.

5. Continue installing CWM. Check the box for “Use boot from phone”. We agree with the proposal “Do CWM Recovery automatically?”

7. To check the correctness of the CWM installation, agree with “Reboot the phone in recovery mode?”

8. Done!

Attention! You perform all actions at your own peril and risk. We are not responsible for possible problems on your device. If you are not confident in your abilities or doubt our good intentions, then it is better not to follow the advice described above! We warned you)

My birthday was approaching, and I wanted to upgrade my phone as an excuse. My desire was strengthened by the fact that my old and faithful Sony Ericsson W200i, which had survived the replacement of two batteries and one case, began to complain of aging diseases, and also could no longer cope with the flow of SMS spam and online notifications from banks. I opened the websites of several electronics stores and plunged into the selection process. The choice was complicated by the fact that I had no experience using a smartphone, so it was difficult to correlate the stated technical characteristics with my needs.

In the last week of September, I saw a new phone, ZTE LEO Q1, in the price list of one of the stores, and decided to take a closer look at it.

What attracted me to the model description:

1. Good (though not Full-HD) screen resolution (800 x 480)
2. The latest version of the system is Android 4.2 (in fact it turned out to be 4.2.2)
3. Two SIM cards (now one is enough for me, but consumer intuition told me that two pieces are better than one piece, if we are not talking about problems).
4. Relatively fast dual-core processor (1.2 GHz)
5. Price! 3,790 rubles (looked at Citylink)
6. There is a GPS module.

What was alarming:

1. According to reviews - short battery life. The battery in this model has a capacity of 1500 mAh, which, in principle, is typical for phones in this price range. A large beautiful screen, 2 SIM cards and a dual-core processor, in principle, should consume the battery faster than a phone with more modest parameters, but I hoped that the difference would be significant and decided to take a risk.
2. Memory capacity (RAM) - 512 MB. True, all phones with 1 GB of memory are noticeably more expensive.
3. The low quality of the camera was mentioned in all (at that time - all two) reviews on the store's website.
4. Slightly heavy, 145 grams.

Actually, I ended up buying this phone from Citylink for the indicated 3,790 rubles. I paid by card, drove up and picked up the device.

Characteristics of the ZTE LEO Q1 (V765M) smartphone

Connection

• GSM bands: 850, 900, 1800, 1900
• UMTS bands: 2100
• Internet access: GPRS, EDGE, 3G
• Modem: yes
• Bluetooth: 2.1
• Wi-Fi (802.11): yes (802.11n)
• Synchronization connector: microUSB
• Number of SIM cards: 2

Display

• Display type: TFT
• Display diagonal (inch): 4
• Display resolution (pix): 800×480
• Number of display colors: 262 thousand.
• Touch screen: yes
• Touch screen type: capacitive
• Multitouch support: yes (2 touches)

CPU

• Processor: MediaTek MT6572W
• Processor frequency (MHz): 1200
• Number of cores: 2

Memory

• RAM capacity (MB): 512
• Built-in memory (MB): 4096
• Memory card support: MicroSD
• Max. memory card capacity (GB): 32

Multimedia

• Camera (MP): 3.2
• Additional camera (MP): 0.3
• FM - radio: yes
• Audio Jack: 3.5mm

System

• Operating system: Android v4.2
• Navigation: GPS

Frame

• Case type: classic
• Length (mm): 124
• Width (mm): 63
• Thickness (mm): 11
• Weight (g): 145
• SIM card type: regular

Nutrition

• Battery type: Li-ion
• Battery capacity (mAh): 1500
• Talk time (hours): 3.3 (I can’t comment on this parameter, I don’t have that many conversations in one day)
• Standby time (h): 200 (in my opinion, this is clearly an overestimated figure, but more on that below)

Other

• G-sensor (position sensor): yes
• Digital compass: yes

With the characteristics more or less clear, it’s time to look at the smartphone itself.

Equipment and appearance of ZTE LEO Q1 (V765M)

There are no surprises or overly creative ideas in the phone's packaging. However, everything you need is written in Russian, and the box looks quite nice.

Opening the box:

Inside, in addition to the phone, there is a battery, a micro-USB cable, a headset, a charger, a booklet with brief instructions (in particular, it shows which end to open the lid from) and a warranty card.

Telephone (closer).

Telephone (from the top end).

To install the battery, we need to remove the back cover.

A disassembled phone, here you can see the mount for two SIM cards, an SD card, as well as a strap for wearing the phone on your wrist.

Here you can see the slot devices for two standard (not “micro”) size SIM cards; they are installed in a “sandwich” one above the other. There is a pictogram explaining what number is assigned to each card.

Both SIM cards are inserted.

(same thing, a little closer)

Putting everything back together - inserting the battery...

It can be seen that the bottom SIM card is blocked by the end of the battery; If necessary, the top card can be removed without removing the batteries.

Attached the strap (from the camera).

In reality, the fastening turned out to be unreliable: after about an hour, this loop came off the plastic pin and the strap detached by itself. On the other hand, I have never seen a phone being carried this way, well, that means I won’t either.

Top end: headset/headphone jack and power button.

Bottom end: USB socket and (probably) microphone.

Phone in hand: front side.

While I was taking pictures, the lower part was already a little stained.

Phone in hand: back side.

Back side, top view.

In appearance, the phone is a neat black “brick”, without any design frills, inserts, bumpers (as well as spoilers, moldings and wings). The corners are rounded, but the device still looks “square”.

The inscription “ZTE” on the back cover looks unobtrusive and does not catch your eye (especially when you are talking on the phone

The plastic from which the lid is made is smooth and does not feel “flimsy” to the touch, but handprints are visible on it.

The case has the required minimum of connectors - micro-USB at the bottom center, a headphone/headphone jack (3.5 mm) at the top. The connectors are not protected in any way.

On the front panel there is, in fact, the screen itself, a front camera, and three backlit touch buttons.

Performance and functionality

So, the SIM card(s) and battery are installed, the phone is turned on, he showed me the proprietary screensaver with the ZTE logo (a burning blue flame), prompted me to go through the standard Android personalization dialog, and the phone can be used.

Tests

Built-in test of all systems and sensors - “Factory Mode”

Externally, the phone's interface is standard Android, without customized shells. Of course, the system contains a number of manufacturer-specific components (prefixed with “mediatek”).

com.mediatek
com.mediatek.CellConnService - telephony
com.mediatek.FMRadio - FM radio application
com.mediatek.StkSelection - interacts with SIM Toolkit, applications on the SIM card
com.mediatek.appguide.plugin - ?
com.mediatek.appwidget.worldclock - probably a clock widget
com.mediatek.apst.target - ?
com.mediatek.batterywarning - something is wrong with the battery
com.mediatek.bluetooth - Bluetooth
com.mediatek.calendarimporter
com.mediatek.connectivity - service menu, everything related to the network
com.mediatek.engineermode - service menu, throughout the phone
com.mediatek.factorymode - a simple test of all systems and sensors, there is a video above)
com.mediatek.filemanager is a custom “file manager” application, very simple.
com.mediatek.lbs.em - engineering menu for Location-based Services.
com.mediatek.mtklogger - setting up system logging
com.mediatek.notebook is a custom Notepad application that can save simple text notes.
com.mediatek.omacp - ?
com.mediatek.schpwronoff - turn on/off the phone according to a schedule
com.mediatek.thermalmanager - something systemic
com.mediatek.videoplayer - video player shell
com.mediatek.ygps - engineering menu for GPS

The first time I connected to Wi-Fi, the phone found an “over-the-air” update and offered to install it. The installation went without any surprises, although I forgot to write down the system version before the update.

Work in phone mode. Talking on the phone is quite comfortable, there are no obvious problems with sound quality, audibility in both directions is good. I can't point out any noticeable disadvantages or outstanding advantages to voice communication, it just works. The proximity sensor works well; pressing extra buttons with your cheek during a conversation is impossible. I read on the Internet that a certain phone from another manufacturer on the same chipset suffers from switching to silent mode when lying “face down” on the table, I checked, no, LEO does not have this effect.

Since the device has two SIM cards, it is interesting to see what “dual SIM” looks like for the user.

When there is an active call with one SIM card, the second number appears unreachable. As far as I understand, this is called Dual SIM Dual Stand-by (DSDS).

When it detects a change in the state of SIM cards (installation or removal), the phone displays a settings dialog that allows you to specify what this card is used for (i.e., the 3G Internet service can be configured for any of them).

The setting for selecting SIM cards when making a call is Russified a little strange,

As I understand it, “Go down the list of notifications to switch to the default SIM card” means that you need to pull down the “curtain” while in the Dialer application and select the card there.

Actually, this is what it looks like:

And this is what the dialogue for manually selecting a card looks like when making a call.

The two cards are assigned different color labels - blue for the first SIM card, orange for the second, so when you receive an incoming call you can immediately see which number they are calling you on.

The standard dialer also includes “video call” and “IP call” items.

((1) — video call, (2) — IP call)

I couldn’t check the video call (at a minimum, I need another phone with video call support, and, possibly, operator support), I haven’t figured out what an IP call is, and whether it can be used profitably somehow. Judging by the lack of settings typical for a SIP client, if it is SIP, then it only works with the support of a cellular operator. It would be tempting to connect it via Wi-Fi to the office PBX at work, but, alas.

Impressions from using the phone interface. When navigating menus, launching applications, scrolling in the browser, typing text, etc. everything works quite quickly, there are no “brakes”. By the way, after a couple of days of using this phone, I began to notice lags in the interface of my trusty Huawei Mediapad tablet (dual-core Qualcomm Snapdragon MSM8260 1200 MHz).

Touch screen sensitivity is average. I didn't have any problems with it, although subjectively its responsiveness is worse than that of the Nexus 7 tablet.

The sensor understands two clicks at the same time.

I would like to say a few words about the touch buttons. There are three of them - “context menu”, “home” and “back”. They do not have any relief searchable by touch, and their backlight turns on for a short time and goes off, for example, when the browser is running. They are not visible in the twilight. Moreover, their sensitivity is such that you have to press exactly on the button icon. If you accidentally hit the button next to it rather than the button, it won’t work. This feature is sometimes annoying, creating the impression that the touch buttons are “dull”.

The screen is bright enough. I'm trying to compare LEO Q1 and Huawei Mediapad, filmed outdoors, shooting conditions - the dim October evening sun begins to hide behind the roofs of houses. That is, there is sun, but not direct.

I cover the screens of both devices with my own shadow)

I think it's quite comparable.

The color rendition of the screen is somewhat rough, or, to put it mildly, sacrificed for greater contrast.

Here, for example, you can clearly see that the blue color has acquired an acidic tint, and the white background has faded somewhat into blue.

The same picture from an angle: on the Mediapad it’s still comfortable to read, on the LEO it’s a little “floated”.

More about the difference in screens using the example of a photograph:

This feature of the screen is noticeable to the eye, but overall it does not interfere, and can even be useful when reading text. Although some people may find such colors annoying.

The operation of the W-Fi module does not raise any complaints; on my home network the phone connects at a nominal speed of 65 Mbit/s (Mediapad on the same network always shows 54 Mbit, although according to the specification it also supports 802.11n). The phone connected to the working network (with WPA-Enterprise authentication and hidden SSID) without any problems

There is GPS, it picks up satellites quite quickly (if there is Wi-Fi - very quickly), both devices tracked my path from home to work, so to speak, “neck to neck”.

I want to pay special attention to the points that seemed “problematic” before the purchase, namely, a bad camera and a weak battery.

The camera really doesn't shine with quality.

Examples of photos from the phone

Examples of photographs taken in the same place and at the same time, but with a Nikon Coolpix S2700 digital point-and-shoot camera.

Examples of videos shot with a smartphone camera

on the street

indoors

Power supply. The relationship between Android devices and batteries is so complex and ambiguous that it’s a little scary to begin the further story.

Suffice it to say that while writing this review, I managed to change my opinion about the energy efficiency of this phone three times, and I’m not sure that I won’t change it in a week.

Short conclusion: my battery lasts about 30-35 hours, depending on usage. This means that it makes sense to carry a charger with you (or at least a lanyard, since it’s standard, unlike the Mediapad).

Notes that do not apply to this particular model, but, probably, to any phone.

When buying a new phone (or a new battery), be sure to calibrate it. Fortunately, the phone is a smart enough device to take care of almost everything on its own; our task is only to provide it with three or four cycles of complete discharge and full charging. In my case, the phone suddenly turned off twice when the charge indicator showed 28-30% charge (that is, it considered a completely discharged battery as having 30% capacity, and undercharged it by about 30%. Attempts to estimate power consumption and operating time in these conditions, naturally, gave the most disappointing results.

After three cycles with a full discharge, everything became much better.

The second note, specific to Android: spend a little time and effort to identify the main “wasters” of charge, then it will more than pay off.

(Digression: One of the applications that I installed on the phone on the very first day, it turns out, prevented the phone from falling asleep, as a result of which the CPU almost constantly worked at a clock frequency of 1 GHz, as a result, battery consumption remained stable at around 4-5% per hour no matter what I did with this phone.)

I used the BetterBatteryStats () app for this, although there are other alternatives.

I also used the Greenify () application to “freeze” some background services when the phone falls asleep, but in my opinion, the effect of optimization with its help is noticeably less than I expected. In addition, it requires root rights to operate.

So, let's move on to the power consumption of LEO Q1.

The most information-rich picture:

Battery consumption graph in different modes of use.

When Wi-Fi and mobile data are turned off and the phone is essentially in phone mode, BetterBatteryStats shows consumption at 1% per hour. This gives us a phone lifetime of about 100 hours.

This is what the standard Android battery indicator tells us:

This shows that network connectivity and Wi-Fi have a significant impact on consumption.

CPU States:

It can be seen that the processor is in Deep Sleep most of the time, and this is very good). If this is not the case, look for which app is keeping him awake.

The picture was glued together from two, all the graphics did not fit on one screen. By the way, there is a visible “stick” at a frequency of 1.3 GHz, although according to the specification our processor operates at a maximum of 1.2 GHz.

Skype is confidently leading in wakelocks. It kept the processor awake for two and a half hours.

Well, and a collage from the long tail “Others”

I don’t draw conclusions from it, perhaps someone will be interested.

I don't play games, so I can't evaluate the battery life in this mode. Rather, I am a person with Internet-textual inclinations, and with textual inclinations in the style of Livejournal/Reddit, and not Facebook.

And this is what “bad” graphs look like. These pictures were taken a few days earlier, before I deleted a couple of suspicious apps from my phone.

Here you can clearly see that for 12 out of 16 hours the processor worked at a frequency of 1 GHz, which could not but lead to increased battery drain.

In a good way, the “Deep Sleep” column should be the longest.

And here you can see that almost all this time the phone was “sleeping”, moreover, with Wi-Fi turned off. As a result, with an average discharge rate of 3.5%, the phone was going to last about 28 hours.

This problem was solved when I deleted a certain free alarm clock application (that I installed) from my phone. I just got around to finding where the standard Android alarm clock is set. Miracles, and that’s all!

As a result, I estimate that in my mode of use the phone is quite capable of living on one charge for one and a half days (day + night + day), and on the second night it can be recharged again. This is not very much, but for a city dweller who rarely goes on business trips, it is quite acceptable.

I can’t say with certainty where to classify the presence of an FM radio in a phone. It seems to me that this is a purely youth “feature”. Operates in the “imported” range 88-108 MHz. The standard application for FM radio looks spartan, although it can do everything you need from it - scan the air and record to a file (the format is the same as the voice recorder - 3gpp). It can also show RDS data.

Standard FM radio application

Through the engineering menu, it is possible to set an arbitrary value for the receiver tuning frequency; theoretically, this would allow, in addition to the radio, to tune in to the audio channel of terrestrial TV. In fact, it turns out bad. Firstly, because television broadcasts occupy a significantly larger frequency range than FM music. Secondly, it seems that the frequency step in the chip used is 0.1 MHz, and television sound has a carrier whose frequencies end in 0.25 or 0.75 (see http://www.tv-antenna.narod.ru/list1 .htm). I was able to “catch” a couple of TV channels from the lower end of the range this way, but it sounded too bad to be useful.

In general, it will not be possible to listen to conversations of the Colombian police using our phone.

Engineering menu for FM radio

Dictaphone

It is there, the quality of the recording is average, but recording a thought that suddenly comes to mind is quite suitable.

Additionally

In the “memory” panel there is a switch, “where applications are installed” - “phone memory” or “internal device memory”. I couldn't find any information on what exactly this switch does or if it can be used to install large games onto an SD card.

The USB connection setup screen allows you to connect your phone in CD-ROM mode, which contains drivers for the phone. These drivers are needed to use ADB and will probably only be useful to programmers. I tried it, the drivers are installed successfully in both Windows XP and Windows 7 (64bit).

When describing functionality, I always want to quote Marshak: “In an open field there is a tower, it is not low, not high.” On the one hand, the phone does not have a single “killer feature” that could make it preferable among its peers.

The presence of two SIM cards, it seems to me, should be a plus for a person who makes a lot of calls (usually on work matters), which logically implies the usefulness of an increased battery capacity for such a device, but this is not the case with this phone.

On the other hand, the phone turned out to be quite fast and attractive, with the latest version of Android, and, most importantly, inexpensive.

I enjoy using this phone (this is my first smartphone, as I already said), and over the past week it has already slightly replaced its OS colleague, the Mediapad tablet, in my life.

Would I buy such a smartphone for my wife or children? Perhaps yes, if multi-colored covers were available for it. You can’t count on ZTE accessories appearing in stores soon, and having two identical black bricks in your family risks getting them mixed up

Smartphone discussion page in our VKontakte group -

And the article getting Root ZTE Leo Q1 will help you!

What is Root?

For those who have just become a beginner or are not an expert in the vast world of Android and are not particularly familiar with the concept of how - Root Android, as well as why it is needed, what can be done after obtaining Root rights, or how to subsequently get rid of them if they are no longer needed, all this can be found in the detailed article -!

First of all!

There are no "left" links or unnecessary actions in this article! If you really need Root Rights, then read carefully and follow step by step, this is a guarantee that you will do everything right! This article on obtaining Root rights is divided into two parts: The first part is Required components and conditions, the second part is Instructions How to get root rights using the received files and programs. If, in the process of obtaining root rights, Android constantly reboots or is in the process of eternal loading (happens extremely rarely, but still), then it’s worth it. Now let's start getting Root rights!

Android manufacturers sometimes release new firmware on which you cannot get Root using one of the suggested methods. If the article contains alternative methods, try them. Doesn't work anyway? Indicate the Android version and firmware version in the comments (don't write angry shitty comments, it won't do you any good or anyone else). Android is frozen (will not load), read and re-read from the very FIRST PARAGRAPH, all the necessary links are present in the article!

Still have questions?

Necessary to obtain Root rights

1. Charged ZTE Leo Q1 smartphone, at least 50% battery capacity

2. Enable the ability to install applications not from Google Play ""

3. Download the latest version of the applicationFramrootand install on your smartphone

Instructions for obtaining Root ZTE Leo Q1

1. Download the Framaroot application to your smartphone and install it. If such a window appears, allow and continue

2. Find the Framaroot icon in the menu and launch the application 3. Select SuperSu from the prepositional choice (SuperSU and SuperUser These are application administrators Root rights)

4. Select and click on any prepositional character - Gandalf,Boromir, Sam, Frodo, Legolas, Aragorn(one of these characters will give you Root rights)

5. Wait for a notification that Root rights have been successfully obtained

6. Restart your ZTE Leo Q1 smartphone

7. After downloading, find the SuperSu application in the menu, if it is there, then Root rights have been obtained and you have done everything correctly

If Root failed the first time get, reboot Android and try it another method(another Framaroot character)

Video instructions

Check to see if you have Root rights on Android