Lenovo Service Center. Lenovo service center Windows 7 will not install on Lenovo laptop

Hello everyone, today I got another experimental Lenovo G505 laptop for testing, and we will install Windows 8.1 on it, although the process is also suitable for installing Windows 7. This article will be somewhat reminiscent of installing it on a Lenovo G50-30 laptop. All settings will be done exclusively in the BIOS, which sometimes stops many users, especially beginners.

Setting up BIOS on Lenovo g505

And so, in order to get into the BIOS in this laptop model, you should press

As a result, you will be taken to the summary tab, with basic information about the hardware. Some useful stuff here:

• BIOS Version > BIOS version, it will be useful to understand whether it is new or not, if not, then flash it.
• Lenovo SN > serial number
• Processor and hard drive model

Go to the Boot tab, if you have UEFI in the Boot Mode item, then you need to remove it, press enter

Select legacy support

For Boot Priority we also set Legacy First.

Go to the esxi item and save the Esxi Saving Changes settings. Pay attention to the OS Optinized Default item; if we install Windows 8.1, then select the value Win8 64bit, for Windows 7 Other OS.

Go to the BIOS of the Lenovo g505 laptop again and go to the Boot tab.

Below in the Legacy item, using the Fn+F5 key combination, we change and put our bootable flash drive in the first item. We save all the settings again and install the system. The only thing is that I didn’t flash the BIOS at the beginning and after installation I got a black screen in Windows 8.1, see how to fix it, or better yet, update in advance.

I think it wasn't difficult. See you soon.

Lenovo has long been known to the vast majority of users as a manufacturer of high-quality and inexpensive laptops. Laptops have good technical characteristics. However, incidents happen with this manufacturer too. No one is immune from this. For example, installing Windows 7 by default on the model was not possible. Why did this happen and how to install the “seven” on this laptop if it just came from the store? This is what we will look into now.

Why did this happen?

Lenovo didn't have any second thoughts. It’s just that this laptop model was developed and sold in 2013. Let's remember what they were doing at Microsoft at that time? Right. They used every possible means (at times quite aggressively) to promote their new operating system - Windows 8. Some manufacturers were forced to somehow limit the ability to install Windows 7 on their devices. On the company's official website there are no Windows 7 drivers for the Lenovo B50-30 model at all.

The most interesting thing is that updating the BIOS did not solve the problem in any way (although it should have). Curses and all sorts of disasters were rained down on the company. But all this did not last long. Craftsmen quickly solved the problem. The problem turned out to be in the BIOS settings. By default, the manufacturer had preinstalled options that made installing the “seven” impossible. And if you consider that for most users BIOS is a dark forest, then this kind of “trick with the ears” worked quite well on the Lenovo B50-30. How to install Windows 7 on this model? It couldn't be simpler. And now you will see this.

BIOS settings for installing "seven"

The first thing you need to do is go into the BIOS settings. To do this, when loading the laptop, you need to press the key combination FN and F2. Now you should go to the General Settings tab. Here you need to select Load Default Settings and click OK. Next, go to the Boot tab and in the OS Optimized Defaults line, select Other OS. Now all that remains is to exit the BIOS, remembering to save all changes.

In some cases (especially complex ones) you will still have to install the "eight" and update it with its help. Sometimes this is necessary, since the stock BIOS does not always give the user the opportunity to change the operating system in the boot options. But after the update everything should be fine. Next, you can reboot your Lenovo B50-30. Installing Windows 7 is now possible.

Installation process

It is not much different from the standard one. In fact, it's no different at all. But it's better to describe it all. So, the algorithm for installing “seven” after all the manipulations with the BIOS:

• Insert a flash drive or disk with Windows installation files.
• During boot, hold down the key combination FN and F12. A dialog box will appear.
• In the window, select the media (CD-DVD for a disk or USB-HDD for a flash drive). After this, the system installer will begin downloading.
• In the next window, select the installation language and country of location. Click "Next".
• Now select “Windows installation only” and create a disk partition. We remember that "seven" is placed only on the NTFS partition. The remaining partitions can be adjusted after installing the system.

• Click the "Next" button - the installation process begins. The laptop will restart several times.
• After the last reboot you will be prompted to enter your username and password.
• Click the "Next" button and wait. After some time, the installed system will start.

You have completed your Lenovo B50-30. Windows 7 installation is complete. However, before using the system, you will have to configure a few more things. Because after installation, you will have a “bare” operating system in front of you, which cannot really do anything, since there are no devices installed in it. This means that you will have to install drivers.

Device Drivers

What is the problem WiFi drivers (Windows 7) or any other drivers for the "seven" are not available on the official website. And Wi-Fi is critical. After all, without the Internet you won’t be able to download other drivers. There are several options here. You can download drivers from G8. In some cases they are suitable. Or you can go to the component manufacturer’s website and download the latest version from there. But in any case, you will need a second computer with Internet access.

Sometimes on the websites of equipment manufacturers there is no software for the Lenovo B50-30 model. However, there will be a driver for Wi-Fi in any case. It's worth installing just that. And further problems can be solved through the “Device Manager” in the installed OS. It allows you to update hardware drivers from official Microsoft servers. As long as the "seven" is officially supported, they will not go anywhere. The main thing is to get the Internet on this piece of hardware. Once you do this, life will immediately become easier.

Conclusion

Undoubtedly, this article will be useful for those who are “lucky” to purchase a Lenovo B50-30 laptop. Installing Windows 7 on it is possible, although the process is somewhat unusual. For some inexperienced users, it may seem unrealistically complicated. But in reality there is nothing difficult about it. The main thing is to update the BIOS and change its settings a little. After this, it will be possible to install even “Seven”, even “Linux”, or “MacOS” on this laptop.

How to Install Windows on a Lenovo Laptop - LENOVO™ Helpers

How to install Windows on a Lenovo laptop

All that is required of you to successfully carry out the procedure is a bootable USB flash drive and the desire to do a little work. If you follow the instructions described below and carefully read the prompts that pop up on the monitor, then the question: how to install Windows on a Lenovo laptop will not bring any difficulties.

Preparing to install Windows

Reboot your laptop and go into BIOS. Each Lenovo model has its own way to enter the BIOS. The information should be in the instructions for the device. For most models, the F2 or Delete button is suitable.

Now you are in the BIOS main menu, at the bottom of which there is a navigation section.

The first step is to disable the protection. To do this, go to the Security → Secure Boot section and press Enter.

In this window you need to set the value to Disabled to disable the protection.

After this, you need to return to the Main Menu by simply pressing Esc once.

Go to the Boot tab (it can also be called Startup).

The first section of this tab should display your flash drive. Select it and move it to the top of the list using the navigation keys.

Then find the UEFI/Legacy Boot item and select Legacy Only mode. Sometimes this needs to be done before changing the boot order, depending on system requirements.

How to install Windows 7 on a Lenovo G50-30 laptop

In this video I explained in detail how to install windows 7 to laptop lenovo B50-10.

How to install windows 7 on a Lenovo B50-10 laptop

Installing Windows 7 on Lenovo G580 — Fixing the error “Windows cannot be installed on this disk” in the EFI system

After this, press F10 and confirm saving all changes by pressing Enter.

Now you need to restart your laptop again. Sometimes you may need confirmation to boot from a removable storage device. In this case, just press the desired key and wait.

If you didn’t succeed in doing all this the first time, try again. If you doubt your abilities, then simply order a service for professional Windows installation and Lenovo laptop repair, so you will be 100% sure that the OS installation will be done quickly and efficiently.

Installing Windows from a USB flash drive

If the preparatory steps were successful, after restarting the laptop, the Windows Installer will appear on the screen. After downloading it, confirm that you agree with all the terms of the license agreement by checking the appropriate box (as in the figure below) and clicking Next.

The unpacking process will take some time. You need to be patient, and then select “Full installation”.

In the case where the laptop’s hard drive initially consisted of partitions, and the file system was formatted in NTFS, then everything is simple. Otherwise, you will have to delete the hard drive partitions. Just click "Disk Setup" and delete all partitions.

Now you can divide your free space into sections yourself. To do this, click on “Create”, select the partition size you need and confirm your choice. Do this until you have divided all the available space.

Now click on the partition where you want to install Windows and get started, just follow the instructions that appear on the monitor. During the Windows installation process, your laptop will restart, do not be alarmed by this, and do not interrupt the installation process under any circumstances.

Don't forget to select your language and set the date and time. Ready!

The other day I was asked to install Windows 7 instead of Windows 8 on a Lenovo B590 laptop. As usual, I tried to enter the BIOS via F2, then through other keys and oops... it didn’t work. I had to dig around and find a way out, or rather an entrance :) Which I will be happy to share with you today.

I also saw quite a lot of questions on the Internet from those who wanted to change the eight to seven, but everyone had problems logging into the BIOS. Below you can watch video instructions for installing windows 7 on lenovo b590, and if suddenly you can’t watch the video, we read the manual in text version.

How to enter BIOS on a Lenovo B590 laptop

First, turn on the laptop and insert the Windows 7 disk into the drive. Turn it off, remove the battery, and disconnect the power from the laptop. We put the power supply in place and start the laptop from the NOVO button. This is such a small button that is located next to the power button.

After a few seconds you will be taken to the service menu. Select Russian language, keyboard layout - Russian. then select Diagnostics, Additional options, UEFI Firmware Settings.

Now the laptop will require a reboot - Click the reboot button and voila we entered the BIOS.

Now use the arrows on the keyboard to go to the Security section, use the down arrow to select Security Boot and press enter.

Set the Secure Boot parameter to Disabled.

We return to the main BIOS menu with the Esc key and use the right arrows to go to the Startup section.

Select Boot - press enter. In this section, use the arrows to find your hard drive - ATA HDD... and use the + (plus) button located on the right side of the numeric keypad to raise it to the very top of the list. If it does not rise to the very top, then select Windows Boot Manager and use the - (minus) key to lower it down.

In the same way, we raise the seed to second place - ATAPI CD1

Next in line you can put the device from which windows will be installed if it is not a built-in drive.

We return again with the Esc key, click down on the UEFI/Legacy Boot item, change the UEFI Only parameter to Legacy Only.

Save the configuration with the F10 key and agree with the enter key.

Keep in mind: if you forgot something, changed it, or configured it incorrectly, you can only enter the BIOS on the Lenovo B590 to restore the default settings by removing the back cover of the laptop (no big deal - just 2 screws) and removing the cmos battery for a while. Then don't forget to set the correct date and time.

How to install windows 7 on a Lenovo B590 laptop instead of windows 8

Now, actually, the Windows installation process itself.

After the reboot, there is no need to press any keys, although we have assigned the F12 key to enter the boot device selection menu; the laptop itself will find the boot device and show the installation menu.

At the beginning of the installation, be sure to select Full installation.

how to partition windows 7 hard drive

Next you will go to the hard drive where you will have to delete all existing partitions. Everything is required, otherwise you will not be able to reformat the screw from CDA to NTFS. To delete, click on the right Disk setup - select partitions one at a time and click delete.

And don't forget to think about the fact that you are losing your factory warranty. And if changing the operating system is more important to you than guarantees, then we continue dissecting the hard drive.

Now we need to create 2 partitions, we don’t count another one that the system will create itself with a size of 100 MB. To do this, click Create on the right, select the desired size (I set it to 200,000 MB - slightly less than the second partition) and click OK. We do the same with the rest of the unoccupied space, only we don’t set the size, but leave it as the system suggests.

We are done with partitioning the hard drive, select the second partition (the first is occupied by system files and has only 100 MB of space) and click on installation.

The buyer of a Lenovo laptop can get one of three operating systems: Free Dos, Linux, or Windows, which is limited in terms of functionality.

Usually this situation does not satisfy the user, and he installs a full-fledged and familiar version of Windows. You can cope with the task on your own, eliminating the need to hire third-party computer specialists and avoiding unnecessary costs.

You will learn how to do this as you study the information below. The instructions are relevant for modern versions of Windows. Reinstallation differs from installing from scratch in that in the first case, at the appropriate stage of work, it is strongly recommended to format the partitions in order to avoid confusion and reduced performance in the future.

After completing the preparatory steps for the laptop for sale, it is configured to boot from the hard drive. The main problem with installing the OS on Lenovo is the security enabled in the BIOS. Your task comes down to setting up the BIOS on the hard drive and booting from a CD or flash drive.

First turn off the laptop, if it is turned on, and do the following:

press the power button;


wait 1-2 seconds (until the startup screen appears on the display - the word LENOVO on a black background), after which we press the key on the keyboard several times to enter the BIOS menu. In modern Lenovo laptop models, the same keys are responsible: the F2 button opens the service menu directly, the F12 button opens the boot device selection section.

The Delete button or a combination of Fn and keys from the “F” group can also work - this is specified for a specific model and is usually determined experimentally;

We study navigation (information is given at the bottom of the display). The task is as follows: open the Security (Secure) section, from there go to the Secure Boot category and press the Enter key;

set Secure Boot to Disabled mode, i.e. disable protection;

Press the Esc key to return to the BIOS main menu. From there we move to the Boot (Startup) section;

in the Boot section, the task comes down to setting up the laptop to boot from a CD (CDROM) or flash drive. To do this, move the appropriate option to the top of the list. Typically, you use the +/- keyboard buttons to change positions, but there may be differences depending on the specific version. Please check this point in the navigation information (listed at the bottom of the BIOS setup menu);

press Esc, find the UEFI/Legacy Boot item and configure it to Legacy Only mode (in some cases, this action must be performed before performing the manipulations from the previous paragraph, check individually). Press the F10 button and confirm the desire to save the changes made by pressing Enter.

Preparing a distribution kit for installing Windows on Lenovo

It is assumed that you have an original disk with the Windows operating system. In this case, it is enough to insert the disk into the drive, restart the laptop and follow the further instructions of the bootloader.

But if you have to install the operating system from a flash drive, or if the original disk is lost, you will have to make a boot image yourself. There is nothing complicated about this. First download/save the required version of Windows onto a working computer and get started.

To create a bootable USB flash drive, do the following:

• download the UltraISO program from the official website. If desired, use another program with similar functionality - the procedure will remain identical. UltraISO is the most popular and convenient option;
• after waiting for the package to download, run the installation file and follow the bootloader’s recommendations;
• right-click on the shortcut of the installed program and run the software as administrator by selecting the appropriate item, or you can directly launch the ISO image itself;

in the program menu that opens, click the “File” button, then “Open”;

We find the previously saved image of the operating system, select and open the “Boot” section. There we select the item “Burn hard disk image”;

the program will open a pop-up window. Make sure that the removable drive is correctly identified. If an error is found, we make the appropriate changes.

Important! When choosing a recording method, be sure to set the mode to –USB-HDD+.

press the “Record” button. In the “Hint” window that opens, the program will prompt us to delete everything from the flash drive. Let's do it. We are waiting for the creation of the bootable flash drive to complete.

In a similar sequence, using the UltraISO program, a bootable CD or DVD is created.

Windows installation

The BIOS is configured and the boot device is prepared. Let's proceed directly to installing Windows. To do this, insert a disk or flash drive into the laptop and reboot the device. The laptop will independently “understand” how it needs to boot. As a rule, no additional user action is required. Some models “ask” to press any key to boot from a removable drive - we do this.

We wait for Windows to unpack the files, then select “Full installation”.

• if the hard drive is initially partitioned and the file system is formatted in NTFS, proceed with further installation;
• if the system is CDA, first delete the hard disk partitions. To do this, click the “Disk Setup” button and delete partitions one by one.

Here we can divide the free space into several sections. To do this, click the “Create” button, indicate the desired size (preferably 30–60 GB for the system) and confirm your actions. We repeat until we have allocated all the available space on the hard drive.

Select the partition reserved for installing the operating system and click on installation. There will be no further features that require detailed individual consideration. You need to follow the installer's instructions.

The computer will reboot several times. However, there is no need to “touch” it - the system will do everything itself. All you have to do is select the desired language, set the date/time settings, and set a username and password.

Common problems when installing Windows

The most common among users are two typical mistakes, the admission of which in the process of preparing to install Windows can make the successful implementation of the upcoming event impossible.

Firstly, the wrong choice of format at the stage of formatting the flash drive.

You need to choose either FDD or HDD.

Secondly, using the wrong boot image. Windows installation discs fall into two categories:

• Bootable – designed for a “clean” installation of the operating system;
• non-bootable - they are used primarily to solve various problems and work only from the Windows interface.

To cope with the installation of the operating system according to the above sequence, the user must correctly emulate the image onto the disk/flash drive.

Thus, there is nothing super complicated about installing Windows on Lenovo yourself: you just need to consistently follow the relevant recommendations. Follow the instructions you have studied, be careful at every stage, and everything will definitely work out.