Step-by-step instructions for connecting an Asus router. Router asus rt n12 connection and configuration. Setting up WiFi on Asus routers

The Asus rt-n12 router is a fairly popular budget router that successfully implements all the functions necessary for a simple home network. The device is a portable WiFi access point with an information exchange speed of up to 150 Mbit, while the device supports the common 802.11n communication standard with an operating frequency of 2.4 GHz and is equipped with 4 LAN ports for “hard” connecting local computers.

Asus rt-n12 router: indicators and connectors

There are seven LED indicators on the front panel of the router:

1 - power indicator (Power);

- off – power is not connected;
- steady green light means the system can be used;
- flashing quickly - process.

2 - WiFi wireless network status indicator;

- “off” – no power (or the network is disconnected);
- lights up solid green – the system is ready to exchange data via a wireless channel;
- flashing – data is being transmitted (wireless network).

3 - indicator of connection to the Internet (WAN);

- “off” – the Internet from the provider does not reach the router (there may be problems on the line or the service has been suspended for non-payment);
- lights up steadily – active connection to the Internet;

4 - local network connection indicators (LAN ports 1-4);

- “off” – the network cable is not connected (or there is no electricity);
- lit – the corresponding port is busy actively connecting external devices to the network via an Ethernet cable;
- blinking – data is being transmitted (via cable).

The rear panel is equipped with several connectors for an RJ 45 connector and switches:

- one separately located WAN port (for connecting an Ethernet cable);
- LAN1-LAN4 connectors (connecting network devices);
- one round connector for connecting the power adapter;
- standard power button;
- WPS button for quick authorization in the home network;
- button to reset the router to factory settings (hold for 7 seconds);

How to connect Wi-Fi router asus rt - n12

It’s quite simple to install and configure the connection to the asus rt n12 router yourself:

- connect the power adapter plug to the DC In socket located on the back panel of the router;
- connect the power supply to a power supply with a voltage of 220 V;
- for initial setup, use a “hard” connection of the asus wireless router access point to the computer via an Ethernet cable (to avoid wireless interference);
- connect the Internet cable provided by your provider to the WAN socket of the asus rt n12 router (if you need to connect this port to the LAN connector of the modem);
- connect the LAN port of the router to the connector of the network card of a “classic” computer using an Ethernet cable from the “basic” set of the router;

- if you have a TV set-top box, also connect it to the LAN connector of the router;
- turn on the power button.

At this point, the installation and connection of the asus rt n 12 Wi-Fi router is completed - the device is completely ready for use. Step-by-step configuration of the modem is carried out through the built-in web interface of the device, which can be accessed through any Internet browser installed on the computer.

To enter the router settings, enter the combination of numbers 192.168.1.1 in the address bar and enter the authentication data in the window that opens.

By default, the login and password “admin/admin” is used.

If the router was in use before, you should first reset the settings of the asus rt n 12 router to factory settings according to the instructions in the final part of this article.

Setting up an asus wirelessroute rt n12 router for Rostelecom

To configure the asus rt n 12 wifi router to connect to the Internet through providers such as Rostelecom and Dom ru, go to the router settings, find the “Advanced settings” tab and select “WAN” here.

At the top of the window, set the following Internet connection settings:

- WAN type – you must select PPPoE from the drop-down list of connections;

Most Rostelecom subscribers use a PPPoE Internet connection. However, when setting up a router yourself, it is still recommended to clarify your type of Internet connection: this information can be found in the contract with the provider or clarified by calling the technical support of your Internet service provider.

- the choice of port for setting up IPTV STB depends on which port you connected the set-top box to, but by default it is recommended to use the LAN4 connector;
- enable UPnP – mark the option “Yes” with a marker;
- get a WAN IP address automatically – select “Yes”;
- enable PPPoE relaying – it is recommended to set the option “no” from the list.
- in the username and password fields, enter the data received from the Rostelecom operator for connecting to the Internet.

Setting up an asus rt n12 router for Beeline and MTS

In general, the instructions for setting up an asus rt n12 router for MTS, Beeline and other “mobile” providers are similar to setting up a router for Rostelecom.

Here, in the “WAN” - “Internet Connection” tab, set the following values:

- WAN connection type - set the L2TP item;

- enable UPnP - set the marker to “Yes”;
- obtain a WAN IP address automatically – check “Yes”;
- connect to the DNS server automatically - select the “Yes” option;
- L2TP server (VPN) - for beeline, enter this address tp.internet.beeline.ru.

“Username” and “password” in this case are issued to the subscriber by the Beeline service provider. Enter them. There is no need to change the remaining parameters - feel free to click the “Apply” button.

However, when setting up a router for MTS, there are certain subtleties.

In the WAN connection selection tab, you must set the connection mode to automatic. Your login and password must be entered into the appropriate tab “Account and connection settings” - you receive them directly from the operator.

How to set up wifi on asus rt n12 router?

Setting up WiFi on the asus rt n12 router is carried out in the “Wireless Network” tab, where you need to set the following parameters:

Configuring the asus rt n12 router to watch IPTV consists of the following steps:

- select the “local network” tab in the menu;
- further IPTV;
- enable multicast routing – mark the “Enable” option with a marker;
- enable IGMP Snooping – set the marker to “Enable”.

Leave the remaining items unchanged and click the “Apply” button to save the new settings.

asus rt - n12 setting up vpn server

Go to the router management menu and follow the following instructions step by step:

Set any IP address in the range from 192.168.10.2 to 192.168.10.254: the asus rt -n12 router simultaneously supports up to 10 clients. In the VPN server tab, you must enter your username and password. Save your changes.
In the network map section you can see the status of your VPN server, its IP address and connection status.

How to reset the settings of the asus rt n12 router?

Resetting user settings to factory settings is quite simple: for this you will need a regular needle or pin. On the back of the router, find the socket labeled “Reset”. Press and hold for 10 seconds. The device has been reset. Release the button.

How to set the password for asus rt n12?

In this step-by-step instructions, we will look in detail at how to configure the Asus RT-N10 Wi-Fi router in its various variants:

RT-N10P
RT-N10+ D1
RT-N10E B1
RT-N10 B1
RT-N10 C1
RT-N10U B

And other modifications of this popular and cheap Asus wireless router. The basic setup of the Asus RT-N10 Wi-Fi router, regardless of its modification, is the same. That is, if you need to configure the router so that it distributes wired Internet to wireless devices, you do not need to know which of these Asus RT-N10 Wi-Fi router options you have. The only possible difficulty is the new firmware 3.0.0.x on some models (black background) or 7.0.2.31 on other versions (although routers do not go on sale with this firmware), but in fact, this is not a difficulty - all the actions necessary for successful setup are completely identical. However, we will include screenshots of this firmware here.

Preparing for setup, connecting the Wi-Fi router Asus RT-N10
How to enter the settings of Asus RT-N10
Setting up an L2TP Beeline connection on firmware 2.0.x, 7.0.0.x (plus setting up Beeline television)
Setting up PPPoE connection to Rostelecom and Dom.ru on Asus RT-N10 with firmware 2.0.x (plus setting up IPTV Rostelecom)
Setting up a wireless network, setting a Wi-Fi password on Asus
Setting up Asus RT-N10 with new firmware
Firmware Asus RT-N10

For novice users who have never set up routers, let me note: there is nothing complicated about this, the whole process will take no more than 15 minutes.

Preparing for setup and connecting the Asus RT-N10 router

Before setting up a Wi-Fi router, you should connect it correctly, and as experience shows, even with this there are problems. And, in addition, pay attention to some network settings that may be critical for successful setup.

First of all, it is recommended to check the settings of the local network connection that is used to configure the Asus RT-N10. In particular, the TCP/IP protocol parameters should be set to “Obtain an IP address automatically.” How to do this is written in detail (will open in a new tab).

The next point to remember: if your provider uses connections like PPPoE, L2TP, PPTP and others, that is, in order to access the Internet, after turning on the computer, you launch some kind of Beeline, Rostelecom, Dom.ru connection from the desktop or from the list of connections in the taskbar, disconnect this connection. And do not connect again either while setting up the router or after the wireless router has already been configured. Those. this connection will be established by Asus RT-N10 itself in the future; you do not need to launch anything, otherwise you will get a result in which the Internet will only be available on the computer, but not via Wi-Fi.

And now about connecting the Asus RT-N10. There are five network connectors on the back of the router. One of them stands out among the rest - connect the cable of your Internet provider to it. And connect one of the remaining ports to the corresponding port of your computer’s network card, and then turn on the power to the router. You can start setting up.

How to enter the settings of the Asus RT-N10 router

Go to router settings

To get into the settings of your Asus router, launch your browser (it's already running if you're reading this, so better open a new tab) and enter 192.168.1.1 in the address bar, after which you should see a username and password request. The standard login and password for routers from this manufacturer are admin and admin, here and there. You may be asked to change your default login information, please do so. After this, you will find yourself on the main settings page of the Asus RT-N10, which looks like this:

On this page, all operations for setting up connections, setting a password for Wi-Fi and other actions are performed, which we will now do.

Setting up Asus RT-N10 for Beeline

In order to configure an Asus router for Beeline, on the main page of the router settings, click “WAN” in the menu on the left, then fill in the parameters for the Beeline L2TP Internet connection, which look like this:

Setting up a Beeline connection on Asus RT-N10 (beeline l2tp)

Basic parameters to set:

WAN connection type: L2TP
Selecting an IPTV port - if you use Beeline television, select the port to which you will connect the Beeline TV set-top box.
Obtain an IP address automatically - Yes
Connect to DNS automatically - Yes
Username, password - your data for Internet access from the Beeline provider
PPTP/L2TP (VPN) server - tp.internet.beeline.ru
Apply the settings. On some Asus firmware, settings are not saved if you do not enter anything in the “Hostname” field. Enter beeline.

If no errors were made, and the Beeline connection on the computer is broken, then after a short time the connection to the Internet will be established and all that remains is to configure the wireless connection parameters. You can make sure that the Internet is working by opening a new tab and trying to access a website. About setting up Wi-Fi on Asus, see below, after the information on setting up a router for Rostelecom and Dom.ru.

Setting up Asus RT-N10 Rostelecom and Dom.ru

In order to configure the Asus RT-N10 Wi-Fi router to work with Rostelecom and Dom.ru providers, which use PPPoE to access the Internet, follow these steps:

In the menu on the left, select “WAN”
Set the necessary connection parameters, the key ones being Connection type (PPPoE), automatic acquisition of an IP address and DNS (you need to set it to “Yes”), your Rostelecom or Dom.ru login and password. The remaining parameters can be left unchanged. If the settings do not save without entering anything in the Hostname field, enter rostelecom or domru. Also, if you need to set up Rostelecom IPTV, specify the port to which you will connect the TV set-top box.

Save the settings and wait a short time. The router will have to establish a connection to the Internet and if you try to access any page, it will open, despite the fact that the Rostelecom or Dom.ru connection on the computer itself is disabled. Now it is advisable to configure the wireless Wi-Fi network settings.

Setting up a wireless network and how to set a password on Wi-Fi Asus

Another of the main tasks when setting up a Wi-Fi router is setting up the parameters of the wireless network, which is necessary so that, firstly, strangers cannot connect to it, and secondly, to make it more convenient for you to use it. Setting up Wi-Fi does not depend on what provider you have - Beeline, Rostelecom or any other.

In order to configure the basic parameters of the wireless network and set a password for Wi-Fi, in the settings menu on the left, click “Wireless Network” and on the “General” tab enter the basic parameters:

SSID (Wireless Network Name) - Enter something of your own here, so you will distinguish your network from others. It is better to use the Latin alphabet, otherwise some devices may have problems connecting via Wi-Fi.
Authentication method - WPA2-Personal
The WPA Preshared Key is your Wi-Fi password, which must be at least 8 characters long.
You don't have to change the other parameters, especially if you don't know what they mean.

Apply the settings. Wait for a message indicating that the Wi-Fi settings have been successfully changed. And, in fact, that’s all - you can try connecting via Wi-Fi from a laptop, phone or tablet, everything should work.

Setting up the Asus RT-N10 router with new firmware

Frankly speaking, I don’t know if Wi-Fi routers with this type of firmware are on sale (in my opinion, yes, for example Asus RT-N10P and RT-N10U), but it can be downloaded and installed on some models of the RT-N10 router . The firmware has index 3.0.0.x and the web interface of the router with this firmware version looks like this:

As you can see, despite the fact that the design style has changed, the location of the settings menu items remains unchanged when compared with firmware 2.0.0.x and 7.0.0.x. Therefore, the basic setup of an Asus Wi-Fi router with new firmware occurs in exactly the same way as was described above for Beeline, Rostelecom and Dom.ru.

Firmware Asus RT-N10

If you want to flash the Asus RT-N10 router, then this is not particularly difficult. First of all, you will need to download the firmware from the official website. Considering that there are quite a large number of modifications of this router, it is important not to make a mistake here. To do this, go to the router settings panel and select “Administration” in the menu on the left, then open the “Firmware Update” tab.

Pay attention to two points: Product ID and Firmware Version - this information tells you which Asus RT-N10 you have, as well as what firmware is currently installed.

At the top of the page there is a link to the firmware page, but you should not click on it - from experience, it does not always lead to the correct router model. Therefore, the best option to download firmware for an Asus router is to go to the website http://www.asus.com/ru/, select products - Network equipment - Wireless routers, then go to the page of your router model, click the “Support” link ", and then - "Download". In the “Software” group you will find all the firmware that can be downloaded and installed on the router. Download the correct firmware version, extract the firmware zip file, and return to your router's firmware update page.

Click Select New Firmware File and then Submit. Wait for the Asus router firmware to complete; it will take about three minutes, during which the connection with the router may be interrupted. When finished, you will see that the firmware version on your router has been updated.

I hope this instruction helped you. If it’s not difficult, share it on social networks using the buttons below.

This article will step by step introduce the configuration of the Asus RT-N12 router. Here you can see step by step and in pictures the process of connecting, setting up, and then operating the router.

This device works with desktop and tablet computers, smartphones, laptops, modern TVs via Wi-Fi, etc. Otherwise, you can use the device's cable connection instead of wireless.

The router is configured according to the following scheme:

In order to correctly configure the router, you will need information about the type, which is specified in the contract with the Internet service provider, and whether the binding is done to the physical address of the network device. Moreover, if the connection is of the type Point to point protocol over Ethernet (PPPoE)/Layer 2 Tunneling Protocol (L2TP)/Point-to-Point Tunneling Protocol (PPTP), most likely you will also need information such as user login, system password, as well as the IP address. Of course, this information is available in the contract.

Note! In some cases, the default network name is set to something other than the factory name, or even a password is entered. Either this router has already been carried out once. One way or another, before each new setting it is recommended to do a full reset to the factory state - this can be done by holding the back button for more than ten seconds - after that all the indicators will go out for a while, a full reboot will be carried out, as well as a return to the parameters set according to default.

Settings via control panel

After connecting the router, and after establishing a signal between it and the computer, you need to:

Enter the following address in the address bar of any browser: 192.168.1.1.
After this, the “Control Panel” will open with a large selection of settings. In this case, a settings wizard is required. To do this, click on the “Go” button.
After this, the system will ask you to come up with an individual password for the “Control Panel” of the router settings. You must provide a password in any case. First in the main field, then in the additional confirmation field, and after that you should move to the next window by clicking on “Next”.
In the next window of wireless network settings, you need to enter the “Network name” line » enter the name of the Wi-Fi network you are using, and in the “Network key” line » register a new key that will be used when connecting to the network. You must click "Apply" » and wait a little.
The router will reboot. In the network connections field, in place of the old Wi-Fi network, a new one will appear, with an individually specified name. When connecting to it, a new password will also be used.
Once connected, you need to return to the “Control Panel” again. There you should open a page with information about this connection. After clicking on “Next” » , the system will display a new window.
There will be an inscription in the new window « Sign in » and a request for a login with a password. This is the same login and password for the settings menu. They should be entered in the appropriate fields.

Configure manually

If everything goes smoothly, then everything is in order, and most likely there will be no additional problems during connection. This means that in this case the provider connects using “Automatic IP”, and thus the router sets all the parameters independently. In this case, at this stage you can already connect to the Internet and work.

However, there is another option. In some cases, providers use a connection type Layer 2 Tuneling Protocol (L2TP), Point to Point Tuneling Protocol (PPTP) , static ip , or Point to point protocol over Ethernet (PPPoE) (used by providers such as Beeline or Dom.ru), in this case you will have to manually configure a number of parameters.

Step 1. If the provider uses the above connection technologies, then in the “Manage Settings” menu, when the connection is checked, the system will offer several types of Internet connections to choose from.

Step 2. In the next window, you will need to enter the username and password that are used when connecting. This information must be specified in the contract from the Internet service provider. You may also need to enter information such as IP address, service name, etc. Each situation varies depending on the Internet provider and the connection itself.

Step 3. During setup, immediately after the router connects to the Internet, you will be asked to configure Wi-Fi, etc. Everything should be configured immediately, according to the principle already indicated. You can change your Internet connection (WAN) settings yourself. To do this, go to the main settings page, find the “Internet” tab there » and select "Connection" » .

This page contains the basic and most important Internet connection parameters for the Asus rt N12 router. After the name of the wireless network and password have been remembered, when the Internet is working normally, you can close the settings menu.

How to set up Wi-Fi and change the password

In order to change the name of the Wi-Fi network at any time, or change the key used when connecting directly to Wi-Fi:

A number of network settings, including channel parameters, are located in the left panel on the main page, on the “Wireless Network” tab » .

Once the network name and also the key are changed, the access point will also change, so of course you will need to reconnect the first time. In some cases, it is not possible to connect - sometimes such problems occur after changing the password. In this case, it is recommended to delete the network connection, create it again, and then make the connection again.

How to protect your router settings

Earlier in the article it was already indicated that you need to create a password for the “Settings Panel”. However, in some cases, if the user did not do this in time, or some problems arise, or you need to change the password, you need to do the following:

Note! When entering the add-in menu, this particular password will be entered. It should be written down separately, otherwise you will have to roll back the router to factory settings.

Video - Setting up ASUS RT-N12 router

In order to configure an ASUS router there are two ways. The first is to use the special Quick Device Setup Wizard. It is specially integrated into the web configurator so that an unprepared novice user can easily connect the router to the provider’s network and set up a Wi-Fi wireless network. Of course, its capabilities are very limited, but it allows you to configure the most basic functions of the router without any problems.

The second way is to work with a full-fledged web interface, which allows you to fully reveal the full potential of the device, if necessary, squeezing out of it everything that it is capable of. Let's consider each of the options separately.

In both cases, in order to enter the configuration interface of the Asus router, you need to enter the device’s IP address in the address bar of your web browser - 192.168.1.1 . When prompted for authorization, enter the login "admin" and password "admin".

Quick Internet setup on an Asus router

When you first access the web configurator, you will see a wizard prompt to quickly configure the device. We agree. The first step is to change the default access password:

Instead of the default "admin" use any other one. It is desirable that it be more or less complex: consist of 7-8 characters, contain letters of the Latin alphabet, numbers and special characters @#$%&.

The next step is to select your Internet connection type:

Asus routers can work in the network of almost any Russian Internet provider - Rostelecom, Dom.ru, TTK, etc. The main thing is that you need to check with technical support in advance which communication protocol the telecom operator uses.

Most often, either "Automatic IP (DHCP)" or "PPPoE" is used.
In the first case, usually, you don’t need to specify anything additional, but in the second, you will need to enter the login and password for the connection, which you were given when concluding an agreement with the provider. Click on "Next".

In the next step, we will configure the Wi-Fi wireless network:

Here you will need to enter the network name SSID and the password for it is Network key. If you are setting up a dual-band router, here you will need to enter the WiFi name and password for the 5GHz band. Click on the "Apply" button.

At the last step of the wizard you will see summary information:

How to set up an ASUS router for Rostelecom, TTK and Dom.ru

This manual is relevant for ASUS RT-N10, RT-N11P, RT-N12, RT-AC51U, RT-AC52U, RT-N56U and RT-N66AU routers, as well as for all other models running on ASUSWRT software (web interface in dark colors).

In order to set up a connection with your provider, go to the “Internet” section, “Connection” tab. It looks like this:

Most branches of the largest Russian providers Rostelecom, TTK and Dom.ru use the PPPoE protocol. Select it in the "WAN connection type" field:

Be sure to ensure that the "Yes" checkboxes for WAN, NAT and UPnP are checked.

Below, please make sure that the “Yes” checkboxes are checked for the “Obtain a WAN IP address automatically” and “Connect to the DNS server automatically” items:

In the "Account Settings" section, you must specify the Login and password for connecting the ASUS router to the Internet, which were given to you when concluding the agreement.

There is no need to change any further parameters. Click the "Apply" button and check your Internet access.

Dynamic IP (DHCP)

Some branches of the Rostelecom and TTK providers use the "Dynamic IP" connection type, when the router receives the address from the provider's DHCP server and no other connections or protocols need to be used.
To configure, you need to select the WAN type "Automatic IP".

Be sure to check that all the points indicated in the figure are ticked.
Pay special attention to the fact that DNS server addresses should also be obtained automatically by the device.

How to set up an ASUS router for Beeline

On the Internet, the Beeline provider uses the L2TP protocol for connection:

We leave obtaining an IP address and DNS server in automatic mode.
In the account settings, enter the “Username” (usually this is a personal account) and the password that was issued by the operator’s representatives.
All that remains is to enter the address of the Beeline VPN server: tp.internet.beeline.ru
Click the "Apply" button.

Setting up Wi-Fi (Wi-Fi network)

In order to set up a regular WiFi network in the 2.4 GHz range on ASUS routers, you need to select the “Wireless network” item in the main menu and the “General” tab:

In the SSID field you must enter the name of the Wi-Fi network you are creating. Any word in English can be used in this capacity. Then you need to select the "WPA2-Personal" authentication method and enter the password in the "WPA Pre-Shared Key" field. As a rule, there is no need to change anything else, since the most optimal parameters are set by default.

To configure WiFi 5 GHz on ASUS routers (RT-AC51U, RT-AC52U, RT-AC55U, RT-N56U, RT-AC66AU and AC68U), you need to set the value in the "Frequency range" field 5 GHz:

And then everything is exactly the same as usual: we enter the “SSID” (it is desirable that it is slightly different from the one used on 2.4 GHz), indicate the verification method “WPA2-Personal” and the WiFi password, Click the “Apply” button .

Old web interface

If you are using old firmware of ASUS routers made in blue tones (RT-G32, WL-520GC, etc.), then in this case just proceed by analogy. Here are some video instructions that you may find useful:

As you can see from the video, there is no difference in the designation of key parameters in different firmware versions.

For a long time, ASUS stayed away from the network equipment market, releasing only low-end devices, simple white boxes with an unmemorable design and crude software. Just five years ago, Internet providers in Voronezh refused to connect a client if he bought an ASUS router. And suddenly everything changed, as if by a wave of a magic wand. Realizing the promise of the router market, in a short period of time the company was able to develop and launch into mass production several dozen router models - from budget solutions to high-performance premium segment models. Magnificent futuristic design, rich hardware, software based on the OpenSource OpenWRT project, but with proprietary features and an excellent web interface - all this has made ASUS a leader in the market of network equipment for home and office.

Model range of ASUS routers

ASUS produces a full range of routers, from the simplest and cheapest to expensive premium devices. Each category has its own popular models - leaders in sales and user favorites.

The budget segment is represented by models RT-N10, RT-N12. Despite their cheapness, their capabilities are enough to create a home network in the “laptop and three smartphones” format. It should be noted that almost all budget routers from ASUS have a tendency to overheat, so you should not use them 24/7 or in an office environment. These are devices for the needs of a small family or a bachelor. Large providers often install routers for their subscribers as a bonus or promotion. Of course, these are entry-level routers.

The cheapest does not mean the worst. There's just nothing superfluous

The middle-end segment is represented by models AC-51U, RT-N65. These models are 2-band, 2-antenna with USB support and adaptive wireless power control. The presence of USB will allow you to organize network storage on the basis of such a router, provide shared access to a printer, or keep your pets under supervision using an IP camera. Models with internal antennas will be more in demand in a small apartment, in a family with small children or pets, because compactness and the absence of protruding parts are no less important than the power of the Wi-Fi transmitter.

300Mbps over the air, two USB ports, excellent software. And all this for a reasonable price

Major league routers come very close to professional equipment in their range of capabilities, while maintaining an intuitive and flexible user interface in which most of the settings are performed automatically or using simple step-by-step instructions. Such routers are equipped with four or even six effective antennas for successful operation in two bands simultaneously, the number of LAN ports has been increased to eight or even ten, and there are also several USB ports, one of which is of the USB 3.0 standard.

ASUS RT-N66U, ASUS RT-AC68U, ASUS AC3200 are the most prominent representatives of the premium segment. Yes, the price for them is steep, but every ruble invested in them is worked out with 100% efficiency. In addition, a router that is “at the cutting edge of progress” will not become outdated as quickly as its cheap brother and will last longer.

A top-end router will not only work great, but also make guests envy

A separate group includes ADSL routers, combined devices that carry an ADSL modem and the hardware of a simple wireless router on board. The price for devices of this class is unreasonably inflated by the manufacturer, so it will be cheaper to buy an inexpensive router and operate it with a cable modem, which the provider provides for free.

A few months ago I had to advise friends on buying a router for a small apartment. The house is panel, even the partitions between rooms are reinforced concrete, so it is important that the WiFi module works efficiently. We had to choose from models between the lower and middle segments - the customers did not have much money. As a result, I found out that ASUS ships models in the lower and mid-price ranges with disgusting antennas. With a stated gain of 5 dB, it barely reached 2. As a result, the router installed in the bedroom could not reach the kitchen. We managed to get out of the situation by purchasing two antennas from the TP-LINK router on the secondary market and connecting them to ASUS.

Connecting an ASUS router

Any modern router has a managed switch on board, which allows you to connect clients using a UTP8 twisted pair cable, a wireless module that ensures the functioning of the Wi-Fi network and an interface for connecting an Internet channel. ASUS produces routers for three main types of Internet channel: cable, xDsl and 3G routers. Depending on the type of Internet channel, the connection diagram of the router changes.

Cable (classic) routers

In such devices, the Internet provider is connected with a cable of the same standard as wired clients: UTP-8 twisted pair cable. The provider's cable is connected to a connector signed by the Internet, computers are connected to network connectors LAN1-LAN4, wireless devices are connected using a Wi-Fi network.

The port for connecting the provider cable is color coded and labeled

An xDSL router is a combined device that contains an ADSL modem and a wireless router in one housing. The connection diagram for this is a little more complicated, since the provider uses a regular telephone line as an Internet channel. A special device - a splitter - is connected to the telephone socket, and the adsl port of the router is connected to it with a cable. Client computers are connected in the same way as in a classic cable router.

The ADSL router connection diagram is a little more complicated and includes a frequency splitter - splitter

3G routers

A 3G router can be either a specialized device or any universal router equipped with a USB port. The Internet channel is organized via a USB modem that connects to the router.

The 3G modem is connected to the router's USB port

To eliminate the possibility of errors, before setting up any Asus router, you need to connect it to a desktop computer or laptop using a patch cord. Do not perform the initial setup; you can do it via a wireless network; errors may occur.

Older models of ASUS routers support wireless configuration using a smartphone running Android. To do this, you need to install the Asus Router program from the PlayStore application store. Before starting the program, make sure that the router's wireless module is not disabled by a button or switch on the rear panel.

Main menu of the Asus Router program

Access to the router interface: address, administration password

Before connecting the router to your computer, make sure that the network card is configured to automatically obtain a TCP/IP address.

Right-click the “Start” button and select “Network Connections” from the user menu.
Calling network connections from the user menu
In the network connections window, select the desired adapter and use the right mouse button to open its properties.
The network adapter properties contain TCP/IP protocol settings
From the list of protocols, select TCP/IP and double-click to bring up its settings.
TCP/IP protocol is the main conductor of a wireless network
Configure to automatically obtain the network address and DNS server address and click OK.
Automatic receipt of addresses is set

Opening the address 192.168.1.1 in any browser will take you to the ASUSWRT start page.

The web interface can be opened using any browser

Remember! For a router that has been reset to factory settings, the DHCP server is always running. If a network card configured to automatically receive an address does not receive it or receives an address like 254.168.x.x, the router is faulty. Return it to the seller if possible.

Before the first attempt to make changes to the settings, the router will ask for authorization parameters. By default it is admin/admin. If the router is not new, the password may have been changed. In this case, you need to reset the device to factory settings.

The sticker on the bottom of the router contains all the important information about it

Asus router configuration in the ASUSWRT environment

The new version of the software - ASUSWRT is built on the basis of the most famous software project for open source routers - OPENWRT. Combined with the graphical interface from ASUS, the result is a powerful and intuitive tool for configuring and maintaining the router.

DHCP and MAC address binding

If you do not want to waste your router’s resources on encrypting your wireless network or the topology of your cable connections allows unauthorized connections to the router, then the optimal security algorithm would be to bind clients by MAC address and a digital identifier for each network adapter. It should be noted that for clients bound by MAC address, network addresses will need to be entered manually.

Static IP address

Connecting to a provider with a static address is a rare option these days. After all, the range of “white” TCP/IP v4 addresses was exhausted last year, and not every provider has equipment for connecting to the TCP/IP v6 standard; in addition, this option significantly increases the cost of the tariff plan. But if your contract is several years old and you have a static address, setting up a connection using an ASUS router is not difficult at all.

PPPoE connection

Connecting via the PPPoE protocol is the most common, allowing you to connect to the network using a login and password. The network address is assigned dynamically, from the provider’s address space, thus eliminating the need for a “white” TCP/IP v4 address. Almost all ASUS routers, even the most inexpensive ones, support speeds of up to 100 Mbit/s on this type of connection, which is sufficient for most tariff plans.

VPN connection (LTP or PPTP)

VPN (Virtual Private Network) is a mechanism that allows your provider to create a virtual tunnel between your home network and theirs. This connection provides a significantly better level of security and allows you to use various provider services in your local network, such as a file hosting service, a media server, and digital TV. The disadvantages of this connection are the lower access speed, since the protocol is resource-intensive and requires a lot of computing power. To fully use a secure VPN connection running using the PPTP or LTP protocol, you will need a mid- or high-end router with a fast processor and a large amount of RAM.

To connect VPN, please follow these steps:

Wi-Fi setup

Correct configuration of a wireless network is very important, since in dense urban areas or in an apartment building, a non-optimally configured router can distribute WIFI at low speed, with errors, or even lose the signal. For a high-rise building, the optimal wireless module would be one that operates in two frequency ranges - 2.4 and 5 GHz. All models in the premium segment and some in the mid-segment are equipped with such modules.

Having identified the least loaded channels in the range using a network scanner program, proceed to setting up Wi-Fi in the router.

To further protect your wireless network from attacks or unauthorized connections, in addition to encryption, you can use the function of filtering clients by mac address. To do this, you need to go to the “Wireless Network MAC Address Filter” tab, activate the filter mode and create a list of devices that will be allowed access to the router.

Filtering MAC addresses on a wireless network

How to set up IPTV

To configure IPTV, go to the “Local Network” section. There, go to the IPTV tab and set the values in the sections as shown in the screenshot. Please note that in the “Selecting an IPTV STB port” section, the Lan port into which the TV set-top box is connected is indicated. Don't forget to enable multicast routing if your set-top box or TV needs to have access not only to video traffic, but also to local network resources and the Internet.

To provide an IPTV device with simultaneous access to both IPTV traffic and the Internet, for the functioning of online services, browser and mail, use the DUAL PPPoE connection type, if it is supported by your provider. If this is not possible, you can try connecting a wi-fi adapter with a USB interface to the set-top box and try setting up TV and Internet services separately.

Setting up digital television (IPTV) parameters

Asus router firmware

A new version of your router software can improve stability and performance and add new features. Premium routers update the firmware automatically as soon as an Internet connection is established. All that is required from the user is to read the message about the downloaded new version of the “software” and agree with its installation.

In entry-level routers and even in middle-segment models, you will have to update the software manually by first downloading the firmware file from the manufacturer’s website.

If during a firmware update the router froze, there was a power failure, you accidentally pulled out the patch cord and now the device shows no signs of life - don’t worry. Any ASUS router can be put into emergency firmware recovery mode and brought back to life using the Firmware Restoration utility. You can download it and detailed step-by-step instructions from the ASUS website in the routers technical support section.

Video: setting up the Asus AC-51U router

Setting up an Asus router on an old firmware version

On budget versions of ASUS routers, it is not possible to install a new version of ASUSWRT - the small amount of RAM and slow processors do not allow this. Therefore, the entire segment of entry-level routers is equipped with old-style software, which has not even changed cosmetically for more than five years. Nevertheless, all the basic settings of the router are implemented quite simply.

ASUS RT-G32 is a typical representative of the outgoing generation of ASUS routers. Providers installed thousands of such routers

Internet connection settings

All budget routers allow you to configure a connection using the PPPoE, VPN (PPTP or LTP) protocols, as well as with a static or dynamic IP address. When connected via a VPN protocol, budget routers will not be able to provide speeds higher than 15–30 Mbit/s, so they are only suitable for users with low tariff plans.