iPhone 5 network disappears what to do. What can you do if your iPhone doesn't receive a connection?

In the world of Apple phones from Apple, not everything is as smooth as the manufacturer portrays. The “No network” error on iPhone is one of the most unpleasant phenomena. Moreover, it appeared on the iPhone 4, then on the iPhone 5 and 5S. And the sixth version did not escape this trouble either.
There are three cases in which this error can appear.

1 The phone was brought to Russia unofficially and locked to a specific operator.
Many who bought an iPhone on EBay or other foreign exchanges encountered this. Due to this, the price of the device is significantly lower. But such a phone will not work without unlocking and will give this iPhone a “No network” error. There is only one way out in this situation - take it to a specialist and pay for unblocking. You can't think of anything else.

2. Software failure of the smartphone.
This also happens - it’s still Chinese, even though it has the Apple nameplate. First, reboot your phone. If it still doesn’t find the network, then try going into the settings and moving the “Airplane Mode” slider back and forth several times:

As funny as it may seem, sometimes it works.

If you have just updated the firmware or reflashed your iPhone, and then the “No network” message appears, then very often the reason is that the time and date were set incorrectly. To change it, connect your phone to a WiFi network with Internet access. After that, go to Settings >>> General >>> Date and time:

There you need to find the slider automatically and set its active mode. If it is already turned on, turn it off and on again. After this, reboot the device.

The reason for the “No network” error appearing on the iPhone may also be a failure in the settings of the cellular network itself. Try resetting them to factory settings. To do this we go to Settings >>> General >>> Reset:

Click on the “Reset network settings” button. The phone will display this confirmation:

Click on “Reset settings”, after which you need to reboot and check whether the network appears.

If all else fails, try updating your iPhone via iTunes. If you have a backup, try rolling back to it.

3. The last possible reason is a hardware problem with the phone.
Most often - with an antenna. Or a radio module. If the “No network” error on your iPhone appeared after you got it wet or dropped it, then most likely this is what led to the problem. There is only one way out - going to a service center. I’ll say right away that repairs are usually not cheap, so be prepared for financial expenses.

How the repair works:

1 We diagnose the imported goods for free
device received by you or our courier.
2 We carry out repairs and also provide a guarantee on new installed parts. On average, repairs last 20-30 minutes.
3 You receive a working device yourself or call our courier.

When you encounter this problem, you first need to find out the reasons that lead to such a malfunction. Experts identify the following most common problems with the iPhone 4s:

system failure;
the settings are incorrect;
a malfunction in the transmitter amplifier;
problem caused by mechanical damage;
failure of the antenna itself;

What to do if the network on your iPhone is lost?

First of all, when you see that the network has disappeared on the iPhone 4, reboot the device. Often the problem of lack of communication occurs due to a failure in the settings or operating system. There are two ways to reboot your smartphone: normal and hard.

After rebooting your iPhone 5, first check the settings. If the device still does not find a mobile connection, it means that there may be a problem with the connection. That is, the data of one operator can be entered in the phone settings, but the SIM card costs another. In this case, go to the “Network Search” item, where set the value to “Automatic”. This will allow the phone to determine the necessary parameters itself. After this, for the settings to take effect, the device must be rebooted again.

Network disappears on iPhone - hardware problems

If the connection in the iPhone 4s constantly disappears, then most likely the problem lies in the hardware. Remember if your phone has been dropped or gotten wet recently. If it did fall, then the following could fail:

antenna;
PCB;
loops connecting individual blocks;
SIM card reader;

Let us remember that the antenna is responsible for receiving and transmitting the signal. Therefore, when the network on the iPhone 5s is lost or you notice changes in the signal, or a short-term loss of communication, then, most likely, this particular transmitter is unstable. To restore it to normal condition, you need to contact our service center for a replacement part.

When you turn off 3G on iPhone, the network disappears

Our specialists will comprehensively examine the iPhone 4c for damage and also check the serviceability of its individual parts.

It is worth noting that the SIM card itself is often to blame for the lack of communication. If the contact pad on it is worn out, then not every gadget will be able to read the data and recognize the SIM card. In this case, you should contact your mobile operator for a replacement.

We serve employees of these companies

Repair in 35 minutes!

But if, after all, the problem is related to a hardware failure in the iPhone 5c, then it is better not to try to restore the functionality of the device yourself. As soon as you notice that the device is not working correctly, take it to our service center for Apple devices. Our qualified staff will carry out diagnostics and accurately identify the fault. Thanks to modern equipment, our specialists will be able to restore the functionality of the iPhone 5c in the shortest possible time.

Articles and Lifehacks

From time to time, users of Apple gadgets encounter a similar situation. If iPhone has no network, first you need to check whether there is at least some signal reception. To do this, go to the settings and activate automatic network search, that is, we search for the network manually. Those who know will immediately pay attention to the corresponding pictogram.

Our article is devoted to the “symptoms” of such a problem, as well as providing first aid to your mobile device. The fact is that in some cases, contacting a specialist may not be necessary, since the user is quite capable of troubleshooting the problem on his own.

No network on iPhone: alarming symptoms

It happens that on our device we see an inscription indicating that there is no network, but at the same time we are in a network coverage area with an excellent signal. It also happens that a smartphone loses connection when it is outside the coverage area, but after returning there the connection does not appear.

Another indicative symptom is the situation when the word “Search” is displayed in the status. In addition, when you go to the main settings, the “About this device” menu, you will notice the absence of any information in the “Firmware” item.

What to do if there is no network on iPhone?

So, if we are faced with one of the above alarming symptoms, or the network is absent under any other conditions, it is worth trying to perform the following manipulations sequentially.

First, turn on and after five seconds turn off “Airplane Mode” by going to the iPhone settings. You can also restart the mobile device itself.
In addition, it is recommended to remove the SIM card and make sure that this is indeed a branded SIM card from the mobile operator. You should also check it for mechanical damage, or simply for the degree of wear. After this, you can try installing the SIM card again.

If all else fails, you need to check the settings of your mobile operator, including for updates. We connect to Wi-Fi, go to the main settings of the smartphone, the “About this device” item. If updates are available to us, the operating system will request their installation. If so, we try to connect the iPhone to iTunes. Next, update the device to the latest version of iOS.

Another way is to reset your network settings. To do this, you need to go to the main settings, select “Reset”, and then select “Reset network settings”.

If there is no network on the iPhone and we are outside the country, we try the following. Select the “Operator” menu through the settings and click the “Automatic” item. If iPhone detects any mobile network, a corresponding menu will be displayed.

It happens that the “Operator” section is not available abroad. In such a situation, you should contact Apple. Disable the above “Automatic” option. After a few minutes, a list of mobile operators that are available should appear. This indicates that our device is working properly. If all of the above manipulations do not help, it is recommended to contact your mobile operator.

It happens that network problems are caused by our careless handling of the smartphone. For example, failure may be the result of physical damage or moisture ingress. In addition, the problem is sometimes due to the fact that the SIM card has failed. In any case, it will be possible to identify the cause only after a complete diagnosis of the iPhone.

So, today we will try to figure out why the iPhone does not connect to the network. The thing is that this problem is not so rare. And users are very interested in its solution. In fact, everything is not so serious and scary. Often you can cope with the problem yourself without outside help. What options are available in our case?

Network failure

If the iPhone 4 does not receive the network (like any other gadget), it is likely that the reason for this was a problem with the cellular operator. That is, it is he who is experiencing a failure. Accordingly, all subscribers will not be able to use the connection.

Fortunately, this is a temporary phenomenon. As soon as the operator corrects the problems, the connection will be restored. You can either wait a little or use a SIM card from another company.

SIM card malfunction

Is your iPhone not connecting to the network? There are a lot of options for the development of events. The next point that should not be overlooked is the malfunction of the SIM card. This kind of problem rarely occurs, but it does happen.

Remove the SIM card from the device, then insert it into another gadget. Still no network? Then all you have to do is change the SIM card. After all, it is precisely this that is the main source of our current problem. It’s not a very serious phenomenon, but detecting it can be problematic. SIM cards rarely become inoperative, and it is difficult to think that this particular problem happened to you.

The possible developments do not end there. So, the iPhone can't connect to the network? What to do in this situation?

Date and time

For example, make sure that the date on the device is correct. Don't forget about time either! It’s hard to imagine, but on modern gadgets, communication problems can arise for incredible reasons.

It turned out that the date is not true? Then change it yourself in the settings to the one that is currently in place. Of course, set the clock to the required value too. Sometimes it is better to do this using a Wi-Fi network and synchronization.

As practice shows, most often this is what helps solve the problem of the iPhone not picking up the network. Therefore, before sounding the alarm, it is necessary to first eliminate this problem. After all, otherwise you may never find out what the matter really is.

Location

iPhone 4 can't connect to the network? This phenomenon is often observed not only among the owners of this gadget. People with regular smartphones sometimes also complain about the device constantly searching for a network. What could be causing this?

For example, your location. Remember, the connection itself is not caught everywhere. And that's why she can disappear. If you are in the subway, elevator or underground parking, no matter how hard you try, you will not be able to make a call. Only in rare cases. Also, the device is not capable of catching a network in the forest and places remote from civilization.

So, the iPhone does not connect to the network. What should I do to correct the situation? You can simply change your location. Move to an area where the net usually catches well. You'll have to wait a few minutes. Look at the result - did everything work out? If not, you need to look for the reason elsewhere. If so, then be more careful about where you are. Mobile communications are not available everywhere.

Blocking by card

iPhone is a device that requires special rules to be followed when using it. Therefore, you should not be surprised at some network failures. It is likely that you still have factory settings. And the smartphone is initially locked to one SIM card, and the mobile device will only work with SIM cards from one specific operator.

This means that if you receive a message from your iPhone 5: “No network,” it’s time for you to change the factory settings. It is advisable to use the appropriate service at service centers for this. Otherwise, you can turn your iPhone into a non-functional gadget. After collecting the factory settings, as a rule, the network appears. Moreover, you will be able to work with all mobile operators without problems.

Viruses

Does your iPhone constantly search for networks? Try to analyze your previous actions. If the connection previously worked normally, but then suddenly began to malfunction, it means something went wrong.

For example, your device was infected with viruses. This is also a common case that is not often taken into account by users. Infection of any system disables the gadget. And on an iPhone this can be expressed through a complete loss of the network or its constant failures.

Of course, to correct the situation, it is necessary to treat the device. This can be done independently using special antiviruses. You can also go to service centers for help. In any case, if you cure the gadget, it will start working at full capacity without interruption.

Gadget malfunction

iPhone can't connect to the network? If you have considered all the possible scenarios, all that remains is to complain about the malfunction of the device. Lack of network can occur in both regular smartphones and fakes. All that remains is to exchange the iPhone for a new one. Or send it in for repair. Fortunately, the described iPhone malfunction is not as common as it seems.

We hope you now understand all the common causes of our problem today. Try not to panic if the network on your iPhone is lost. In order not to spend a long time looking for the cause of this phenomenon, you can immediately take the gadget to a service center. This will help restore the functionality of your smartphone as soon as possible.

During operation, it happens that the iPhone does not catch the network. Situations when the iPhone does not see the network may be related to the device settings and external faults.

Reasons for network loss on iPhone

The reasons why the iPhone 5 has poor network reception may be the following factors:

the presence of external problems with the card, for example, its incorrect cutting;
there is a problem with the antenna on the iPhone;
there are no funds in the account;
card blocking;
A common reason why the iPhone 5 does not see the network is that the time and date are set incorrectly;
bad weather conditions;
blocking by communication adapter;
the formation of some problems with the device itself.

If the above problems occur, it is possible to solve them yourself, without contacting your telecom operator.

Troubleshooting

If the iPhone 5s does not connect to the network, you can try rebooting the device. If there are no results, you should perform the following steps:

1. Go to the setup operation and turn on Wi-Fi.

2. The date and time must be selected (function - “Basic parameters”).

3. Activate the function - “Automatic”. If it has already been activated, turn it off and on again.

4. Wait about a minute and reboot the device.

Perhaps the operator is located in a remote area and is not able to provide quality services. To eliminate this situation, you should enter the operating mode and select the “Airplane Mode” function, then wait 5 - 10 seconds and turn off the device. Upon completion of these operations, the iPhone will begin searching for the network. Sometimes you will need to install a system update. To do this, you will need to go to the section - “About this device”, where there are new system files, and then connect to the Internet, while simultaneously starting the update process.

Very often, the iPhone does not see the network or there is no network in the iPhone 5, due to malfunctions after unlocking. To correct this situation, you will need to completely reset the settings. You will need to attach a card with the choice of the option - “Reset network settings”. Problems with the network in the iPhone 5, as well as in the iPhone 4s, iPhone 6, may occur when activated using the SAMPrefs and Redsnow systems. If the unlocking process is successful, but there is still no network on the iPhone, you need to reset the settings. Then you will need to insert the card and connect to the computer, while simultaneously connecting to iTunes. Make a backup and click on the function - “Recovery” and select the section - “Recognize as a new device”.

Using a third-party iPhone

What to do if the IOS firmware has been updated and during the process of replacing the card, it happens that the iPhone 5, iPhone 4 and iPhone 6 do not receive the network and show no network on the screen? A simple solution in this situation is to create Wi-Fi, using a third-party iPhone, connecting it to the Internet and distributing a wireless communication option.

The procedure to follow if the iPhone does not see the network using another device:

go to the iPhone settings section and select “Cellular”, then the data transfer function;
should be written to the APN field indicator (modem mode). It is possible to find out the settings data from technical support from operators;
Usernames and passwords can be left blank;
Having returned to communication, visit - “Modem mode”, activating it;
Upon completion of the above steps, the section “Modem Mode” should appear, when activated, the device will “give” the Internet.

If this method is not available, all that remains is to carry out the process of flashing the IOS firmware, while simultaneously downloading the firmware file and connecting the smartphone to the computer where iTunes is installed. In the application, select the function “Restore”. This will delete personal data.

Sometimes the reason why the 5 ES or iPhone 4 does not catch the network well may be that the card tray is very dirty. In this regard, it is desirable. thoroughly clean the tray from accumulated dirt and moisture. It often happens that after flashing the iPhone 3gs, it does not see the network or says no network. In such cases, you will need to visit a service center, since, most often, this is caused by the device being blocked by the adapter.

In the process of blocking for cellular communication, when the phone does not support other cards, you should contact a service center, where they will offer unlocking using the IMEI code. Then you can use other cards. During these activities, you will be able to select a suitable operator by visiting the main page of the resource. If the names of the operators are unfamiliar, you can use IMEI - check network logos and order this service, carefully studying the offers provided. If the iPhone is blocked by operators and blocked by ICloud, you will need to unblock ICloud (in this case, the iPhone should not be on blacklists). After this, order the service from a suitable operator. If there is a problem with the iPhone 5 not receiving the network due to problems with the hardware, most likely it will be necessary to visit a service center to repair this equipment.

If the question arises - “why doesn’t the iPhone connect to the network?”, you should first determine the cause of this problem in order to choose the most correct method of troubleshooting.

Here are the common causes of network and signal problems on iPhone.
If your iPhone doesn't pick up Wi-Fi, this will help you.

1. Weak signal

Sometimes buildings do not transmit a cellular network signal well due to the nature of their construction or their location. If you urgently need to make a call, try finding a network in another location.

2. Problems with the SIM card

Does iPhone see a SIM card? If not, it will help you.

3. GSM signal jammers

Some institutions may operate so-called “jammers” - jammers that suppress cell phone signals.

4. You are out of range of the operator

If, for example, you bought a SIM card from a regional operator and arrived in Moscow, then your SIM card will switch to one of three popular operators.
If this switching does not occur and there is no operator icon or signal indicator, try rebooting the phone.
You can independently select an operator from the list. Go to Settings→Operator, disable the “Automatic” option, the list of operators will load.
If this doesn't help, buy a local SIM card.

4. The phone was brought from abroad

An iPhone purchased in another country may be locked to a specific operator. For example, an iPhone from America will only work with AT&T.

5. Reboot required

6. Network settings need to be reset

Open Settings → General, click “Reset network settings”.

7. Phone dropped or exposed to moisture

If you dropped your iPhone and it stopped receiving the network, then most likely the GSM module is damaged. A fall could result in more serious damage, such as damage to the motherboard. Moisture that gets into the phone case is also destructive. The exact cause of the problem can be determined by sending your iPhone for diagnostics. At the Macsouls service center, diagnostics will be done free of charge and in 15 minutes.

8. Software glitch

A system malfunction could cause the iPhone to have poor network reception. If after diagnostics it turns out that the reason is an iOS failure, we will do a flashing. Flashing an iPhone of any model (iPhone 3G/3GS, iPhone 4/4S, iPhone 5/5S/5C) will take no more than 25 minutes.

As funny as it may seem, sometimes it works.

If you have just updated the firmware or reflashed your iPhone, and then the “No network” message appears, then very often the reason is that the time and date were set incorrectly. To change it, connect your phone to an Internet connection. After that, go to Settings >>> General >>> Date and time:

There you need to find the slider automatically and set its active mode. If it is already turned on, turn it off and on again. After this, reboot the device.

Click on the “Reset network settings” button. The phone will display this confirmation:

Click on “Reset settings”, after which you need to reboot and check whether the network appears.

If all else fails, try updating your iPhone via iTunes. If you have a backup, try rolling back to it.

3. The last one is a hardware problem with the phone.
Most often - with an antenna. Or a radio module. If the “No network” error on your iPhone appeared after you got it wet or dropped it, then most likely this is what led to the problem. There is only one way out - going to a service center. I’ll say right away that repairs are usually not cheap, so be prepared for financial expenses.

iPhone 7 users may encounter problems such as poor cellular signal reception. Moreover, communication often fails at the most inopportune moment. The first step is usually to determine the signal cutoff frequency and check the operation of the SIM card.

By the way: poor network reception is the second most popular call to service centers (after glass replacement).

You can send your iPhone 7 for repair to any of our service center branches and the technicians will quickly fix any problem with your smartphone.

Pay attention! If a SIM card does not work in an iPhone 7, but connects to an old Nokia, such a SIM card is still considered faulty. To prevent frequent disconnections from the network, it is recommended to replace ten-year-old Beeline or MTS SIM cards with the latest models (which can be done at any operator office absolutely free).

Diagnosing the problem why iPhone 7 does not catch the network

Phone out of range. For example, after going on a trip or moving to another city, you discovered that your iPhone 7 does not receive the network. Reboot your phone - an available telecom operator will connect automatically. If this does not help, then try going to “Settings”, select “Operator” and turn off automatic operator selection. If there is no result in this case, then all that remains is to buy a SIM card from an operator operating in a given city.
The phone has been flooded or dropped. The accumulation of moisture inside the phone often causes corrosion of the board. If dropped, important components on the motherboard may also be damaged. Such repairs are considered quite complex: a whole set of microcircuits, switches, amplifiers, receivers and other elements that fail both together and separately are responsible for the operation of the phone. To determine the location of the problem, you need to ring the modem's power circuit and check all working elements. Next, the faulty parts are soldered off and new ones are installed. The best solution here is to take the device to a service center.
iPhone 7 does not connect to the network due to a software glitch. If a poor signal or complete lack of network is caused by system malfunctions, then diagnostics are needed to correct such a problem. iOS failure requires flashing the phone, which can be done in the service (in about 20 minutes).
Network suppression. The signal is jammed by walls made of iron, brick or concrete, as well as in elevators and basements. Buildings are sometimes equipped with special network suppression systems that create interference. In any of these situations, the easiest way to solve the problem is to just go outside.
iPhone 7 was imported from another country. The network is not detected due to the fact that the phone is programmed to interact with a specific telecom operator. To unlock such an iPhone, it is better to contact the appropriate services.
The signal reception antenna is faulty. If you see “No Network” on your iPhone screen, then the problem may be a faulty antenna. The antenna is attached to the motherboard using a coaxial cable and a special connector - under mechanical stress it can jump out of the socket. The service center will return the antenna with the addition of a small amount of sealant. As a result, the iPhone, which did not see the network, starts working like new.

The lack of network on the iPhone 7 is often fixed by simply resetting the settings. Go to “Settings”, select “General”, “Reset” and click on “Reset network settings”.

Many iPhone users often experience the problem of network disconnection, which leads many to panic and haunts them.

You need to reboot your smartphone using a deep reboot, for which you will need to press the Home key simultaneously with the “Shutdown” key. The phone may work better by completely resetting all network parameters and updating them, but if this does not happen, you can try several other methods.

Causes and actions when identifying a problem

You need to carefully remove the SIM card and make sure the contacts are completely clean. They can be blown off with compressed air.

Another reason for this problem may be that many buyers of these phones, without thinking at all about the consequences, can damage the SIM card contacts when cutting it. This procedure must be carried out with the help of a specialist in an authorized store.

Another way to restore connectivity on your iPhone is to connect to Wi-Fi and set the correct date and time, which you can quickly do in the settings menu. You can try turning airplane mode on and off a couple of times, which can often help you out.

Fixing the problem with factory unlocking

The most common cause of the error is unlocking using the Ultrasnow program or updating the firmware to the iPad version. This is not at all related to the hardware, since the “no network” error means that the smartphone has accepted the SIM card, but there are obstacles to receiving communication in the software structure itself.

One of the most popular and correct solutions to the problem is resetting network settings through general settings. You can also try to delete information, which may damage the existing program code.

Error when activating/deactivating iPhone 4s using Ultrasnow or SAMPRefs applications

To solve this problem, you will need to insert your SIM card and connect it to your computer with iTunes. Next, when iTunes detects the phone, you need to make a backup and click “Restore”. After the recovery process is complete, two functions will be available to you:

Restoring from backup.
Use your iPhone like a new phone.

If none of the methods help

The main thing is that if none of the above procedures helped you, you will have to contact the service center, since the loss of communication is a rather serious and complex problem that must be left to real specialists to solve.

After all, quite often connection problems arise due to a broken antenna. In this case, for models 4, 4s and 5s, you need to contact an official center, where they can quickly and efficiently replace this same antenna.

It is not worth giving your smartphone to third parties, since the IPhone does not catch the network due to incorrect operation of the internal amplifier. This problem rarely arose in the 4s, however, in the first batch of the five it was present at almost every step, which partly led to a decrease in the popularity of the models.

Many Internet services offer network restoration services for iPhone 4s and later versions via IMEI number. If you unlock your smartphone using this method, you can use SIM cards from any operator on it.

If the mobile operator is blocked in the iPhone 4s, 5s, 6, 6s, then you will have to unlock iCloud, which can also be ordered on these resources, and only then purchase the unlock service from the mobile operator.

Also, if you are interested in games on iOS or Android, you can search for them on QGamer.ru.