How to set up digital television on your TV. Digital terrestrial television, how to set up an antenna under different signal conditions
To begin with, here is a list of currently known TVs that are able to receive digital cable television of the DVB-C standard.
SONY BRAVIA
Almost all models with letter indices D, S, W, X, V, E, Z and a diagonal size of 32 inches or more. series: 3000/3500/4000/4020/4030/4050/4210/4500/4710/5300/5310/5500/5510/5600/5610/5710/5740
LOEWE
Almost all models.
SHARP
model: 46 (52, 65) XS1, LE700
PHILIPS
series: **PFL****N (in the search menu: Country - enable Sweden)
Toshiba
series: AV633/RV633/AV635/RV635/XV635/V635/SV685/LV685
JVC
series: LT32DC1BH, LT26DC1BH
Panasonic
series: TX-P42G10
LG Electronics
(in the search menu: Country - enable Sweden)
- LCD TV series: LH2000, LH3000, LH4000, LH5000, LH7000, LU4000, LU5000
- PLASMA TV series: PS3000, PS7000, PS8000, PQ200, PQ300, PQ600
SAMSUNG
decoding of SAMSUNG TV models:
A DVB-C receiver is built into all models starting from 2009 (letter index B, C or D)! Before setting up, you need to set the following parameters in the menu: Country - Slovakia or Slovenia, Auto search for digital and analogue channels, Source - Cable, Full.
General algorithms for setting up digital channels for various models of LCD TVs
SAMSUNG
- Click to enter the menu - (green button);
- Select in the menu - “Channel” (icon “Satellite dish”);
- Select - “Auto-tuning”;
- Select - “Digital + analogue”;
- Search mode - “Full”;
- Click - “Start”
PHILIPS
First, we read the stickers on the back wall of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to Philips, there is digital broadcasting (at the time the TV was released, but if you update the firmware through their official website, this list may change in subsequent firmware). If our country is not there, then we will have to put some other one from this list. For Philips TVs, the step between frequencies should be eight. Search mode - “Full”.
- Click on the icon - “House”;
- Select - “Configuration”;
- Select - “Install”;
- Select - “Digital mode”;
- Select - “Cable”;
- Select - “Automatic”;
- Click “Start”.
Setup takes approximately 5-10 minutes.
Philips TV models 2011
- Click on the icon - “House”;
- Select - “Install”;
- Select “Search for channels”;
- Select - “Reinstall channels”;
- Select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany);
- Select digital mode - “Cable (DVB-C)”;
- In the “Network frequency” line, enter the frequency;
- In the “Transmission speed” line, enter “6875”;
- Next, select the line “Frequency scanning”.
Setup takes approximately 5-10 minutes.
LG
- Press the button - “Menu”;
- Select “Options” from the menu;
- Select - “Auto-tuning”;
- Select the country - “France, Switzerland, Sweden or Finland”;
- Select the signal source - “Cable”;
- Select - “Digital”;
- Click - “Search”.
Setup takes approximately 5-10 minutes.
SHARP
If your TV model provides for the reception of digital channels, but there is no “DTV MENU” item, then first select another country - France, Switzerland, Sweden or Finland.
- Press the button - “DTV”;
- Press - “DTV MENU”;
- Select - “Installation”;
- Select - “Auto-installation”;
- Click “OK”.
Setup takes approximately 5-10 minutes.
SONY
Since not all SONY models are equipped with a digital tuner for cable TV (DVB-C), you need to check the model of your SONY TV. Models equipped with a DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-32EX402R2 the first 3 letters in the model name (KDL) indicate that the TV is “digital” . In models KLV-**BX***, etc. There are no DVB tuners.
- Press the “MENU” button (for some models it is called “HOME” on the remote control (hereinafter referred to as the remote control). This button is usually blue;
- Select the item “Settings”;
- Find the “Digital Configuration” menu in the list of settings and enter it;
- Select “Auto search for digital stations”;
- A source selection window will open - select the TV connection type. Select "cable";
- In the scan type selection item, select the “full scan” mode:
- Or select “Manual”;
- Next, enter the frequency;
- Leave the access code as “Auto”. Next, enter the symbolic rate;
- Click "start".
Wait until the TV finishes searching for channels.
Pay attention to the bottom of your TV's OSD menu. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.
Panasonic
- Press the button - “Menu”;
- Select the item “Settings”;
- In the window that appears, select “Menu analogue. settings";
- In the window that appears, select “Add TV signal”;
- In the table that opens, put a tick in the “DVB-C” line and go below and click “Start auto-tuning”;
- After searching for all digital channels, going to the main menu in the “Settings” item, the line “DVB-C setup menu” appears. By selecting this item, you can adjust the settings manually (set the frequency and speed).;
The menu on your TV may differ from the model shown. In this case, you need to find tabs that are similar in meaning. If your TV asks for a search step, enter 8 MHz.
When choosing a digital television service provider, you need to lean towards those companies that provide a full package of services, including setup and service. Otherwise, you will need specialized knowledge on setting up digital television on a specific TV model; this may differ depending on the manufacturer.
General concepts about setting up digital television
Any setting is carried out through the menu of a specific TV. You can call this function using the “Menu” key on the remote control.
- To configure digital television channels, call the “Start” menu, then go to “Settings”.
- In the “Settings” menu, select “Search” or “Channel settings”. The system offers analogue and digital channel search methods, depending on the year of manufacture and model of the device being configured. Sometimes the TV supports several standards: DVB-T and DVB-C. In the first case - the “Antenna” mode, in the second - “Cable”.
- To continue setting up, select the first option - “Antenna”. If an error is made at this stage, the setup will not be completed.
- Select the channel tuning method: automatically or manually. The choice is individual, at the request of the user. During automatic tuning, the program itself searches for the required frequencies and assigns them sequential numbers. These numbers can be changed if necessary.
Manual tuning of digital television channels
- On the remote control press the “Menu” key.
- Find the item “Manual setup” (may have a different name).
- Specify search parameters.
- We configure each frequency separately.
- In the search parameters we specify the symbol rate 6750, modulation 128 and individual frequencies: 402, 410, 418, 426, 434, 442, 450 and 458.
Depending on the TV model, the digital television settings may differ from the above algorithm. To clarify the procedure, let's look at setting up TV on specific TV models.
Setting up digital television using the example of a Samsung TV
- Call up the “Menu” by pressing the green button on the remote control.
- Click on the “Channel” submenu, indicated in the list with an icon.
- Go to the “Auto Configuration” item.
- Select the signal source “Antenna”.
- From the proposed options, click on “Digital”.
- Confirm the changes by clicking “OK”.
- Click on the “Start” button.
Setting up a digital TV receiver
- Having connected the digital TV set-top box, turn on the TV.
- We log in by pressing the television remote control on AV-1/AV-2. We put the TV remote control aside, then all manipulations will be carried out using the remote control for the set-top box.
- We select the menu language, screen resolution, and make other minor settings not related to channel search.
- We search for channels using the methods described above.
Digital television in Russia is rapidly gaining momentum. The number of television viewers is growing every day. And at the same time, the question of how to set up digital television on your TV is becoming more and more urgent? In this article we will look at both general points on setting up digital TV, and the features of settings in popular TV models.
General setup
First, let's look at the general aspects of setting up digital cable television.
- We go to the TV menu, select “Options”, and look for the “Auto Configuration” item there. A window will appear in front of you with a choice of signal source, select the one you need and click “Start”.
- After this, a window should appear in which you must indicate that you need digital channels.
- Next you need to select a search mode. Select “Full”. Fields will appear that must be filled in as follows: Frequency - 314,000 (314 MHz), modulation - 256 QAM, transmission speed - 6875 kS/s.
After the search is completed, save the found channels.
Now let's look at setting up digital TV in individual models.
Setting up digital television on LG TVs
- Let's go to options. To begin, in the Country tab, select Finland or Germany
- Next, go to the settings tab, select Auto search, select the connection method, select Cable.
- A window should appear in which you need to select Settings and specify the following data there: Frequency (kHz): 314,000, Modulation: 256 QAM, Network ID: Auto
- If everything is done correctly, after setup, all TV channels and radio stations provided by your digital television operator will become available to you.
We would like to draw your attention to the fact that LG TVs have the automatic channel update function enabled by default, due to which the configured channels are periodically reset and new ones are searched for. We recommend that you disable this feature. This can be done in the “Digital cable setup” menu tab.
Setting up digital television on Philips TVs
- Press the menu button on the remote control and select the “Configuration” section in the window that opens.
- Select the “installation” item, a submenu will appear, select “Channel settings” in it. In the next submenu, select “Automatic.” Installations.” If everything is done without errors, you will see a message that the channel list will be updated. Click “start.”
- Select “reinstall channels”
- In the “country” section, select Finland or Germany
- Connection method: select “cable”
- Go to settings and set the following settings: baud rate: 6.875, baud rate mode: 314.00
- Click “Start”
With the widespread use of modern television, there has been a stir and, accordingly, many questions. how to set up digital television. The reason for its popularity is the variety of channels in terms of direction, quality, language, type of content, etc. Due to the lack of information on setting up digital TV, companies have appeared like mushrooms after rain, charging fees for these manipulations. You don’t have to pay at all, you can actually achieve the goal on your own.
How to set up digital television on a TV - general provisions
Mostly all the methods for setting up digital television reception use approximately the same scheme, but due to the variety of manufacturers, the actions may be slightly different, but their logic is similar. In order not to get confused in all the sequences, it is worth applying the algorithm directly to each TV model. Thanks to logic and intuition, you can correctly configure the settings on almost every TV model using the instructions provided.
- Take the remote control and expand the menu;
- Proceed to the “Options” item;
- Next, you need to activate “Auto Configuration”. With this action, a window appears containing information about the signal sources; it can be a cable or antenna signal. In our case, we need to select a cable;
- At the end of the operation, information about the quality of signal reception should appear in a new window, here you should select “Digital”, then click “Start”;
- The final setting point is “Search mode” and select the method for detecting channels. The proposed fields must be filled in with information. The frequency is 314 MHz, the speed is 6875 kS/s, and the modulation is 256 QAM.
More advanced TV models allow you to perform a network search, which will independently perform all the necessary actions. When the desired method for detecting TV channels is selected, you need to click on “Search”.
If this instruction is not effective, you should use a detailed algorithm for LG TVs. The technique is relevant for almost all models of the manufacturer.
- From the remote control go to the Menu;
- Click on “Options”;
- In the “Country” category, change the checkbox to Finland or Sweden;
- Then go to the “Settings” category and launch “Autosearch”;
- In the fields you need to enter a search method, usually a fairly fast type, frequency - 298 MHz, modulation - 256 QAM, characters - 6952, ID - auto;
- If everything is done correctly, then during the search a number of TV channels will be displayed;
- The manufacturer LG integrates an automatic system for searching and updating TV channels into the system. This function can be inconvenient as the prepared list will be reset regularly. To prevent this phenomenon, be sure to go to the settings for connecting via cable and turn off “Auto channel update”;
- For convenient sorting, you need to remove the check mark from auto-numbering in the “Cable” section in “Autosearch”.
Now let’s look at the Samsung method, because the manufacturer is one of the most popular in the industry. The actions are like:
- Press Menu on the remote control;
- Next, go to the “Channel” category (there is a satellite dish on the icon);
- On the right you need to select the “Antenna” option, and in the type field - “Cable”;
- Now in the “Country” section you need to set “Other”, now you will need to enter a PIN code, by default 0000;
- Go to the “Auto-configuration” menu and specify the source of the signal – “Cable”;
- You need to specify the parameters, they correspond to the data in the first, general example of the article, and click “Search”;
- Now the TV will find all TV channels.
How to set up digital television on Smart TV
Let's look at digital television and how to set up channels on a TV with the Smart function using Samsung as an example. The action is performed fairly standardly, but there are some differences.
- Go to the “Channel” section in the Menu;
- Click on “Country”, you may now need to enter a PIN code, by default 0000, 1111 or 1234;
- Follow the "Other" section;
- Then, step back, select “Cable search options”;
- Standard parameters are now being introduced;
- Again you need to go to “Auto Configuration”, here select the “Cable” source mode;
- You need to activate the “Digital” section;
- Using the search mode, select “Network” and activate the setting.
All methods allow you to create a high-quality connection to digital TV channels and find the maximum available number of interesting programs. Despite the lack of data on devices from Toshiba, Philips and others, the connection method is no different.
If you still have questions on the topic “Detailed instructions for setting up digital television,” you can ask them in the comments
if(function_exists("the_ratings")) ( the_ratings(); ) ?>
With the advent of content in digital quality, numerous fans of the television product have changed the direction of their aspirations towards digital television. Quite active development of this area has caused the emergence of a large number of amateurs and companies that will connect and set up digital television for an appropriate fee. But there's no need to rush. Not everything is as complicated as it might seem at first glance. It is quite possible to cope with the issue of how to set up digital television on a digital TV on your own.
First, you need to consider in detail the principle of setup as such, and then move on to setting up TVs from different companies. At the moment there is some variety of types of digital television. The proposed options relate directly to cable “digital”.
How to receive digital television?
The process of digital television itself is the transmission of video and audio signals to the TV directly from the broadcaster. In this case, digital modulation and a certain compression of the transmitted data are used.
Where to start?
To begin with, you should decide on a company that will provide the selected services and conclude an appropriate agreement to connect the required package of channels. Then we purchase the kit necessary to implement our plan. It will include a fiber optic cable and the necessary modification of the set-top box. The number of set-top boxes will depend on the number of connected TVs. it is necessary to crimp and carefully lay, avoiding pinching.
How to connect to TV?
People who are faced with a similar situation for the first time immediately have a certain number of questions that need to be answered: what kind of TV is needed for digital terrestrial television? How to set it up? What is the cost? At that very moment the answer is on the surface. An ordinary TV with a standard set of options is quite suitable: analog input (tulip), S-Video input, scart input and antenna input. There is no need to talk for a long time about how to set it up. Just insert the cable into a special connector on the set-top box, the other end of the cable is inserted into the corresponding connector on the TV.
You need to connect the power and press the “Power” button. Automatic channel search on the TV will select the frequency of the set-top box and stop scanning. The console menu will appear on the screen.
In general terms
The order of operations and the differences in tabs differ slightly between different TV models. Therefore, it is worth mentioning how to set up digital television reception regardless of the selected TV model.
We enter the TV menu. Select the “Options” tab in the window that appears. The “Auto Configuration” section is a transition directly to configuration. In the next window - “Selecting a signal source” - we select the “Cable” option. The "Start" button will complete this stage. As a result, from several options for the “Search Mode” item, select the “Full” item. Enter the following data in the blank fields:
- frequency (kHz) - 314,000 (314 MHz);
- modulation - 256 QAM;
- transmission speed - 6875 kS/s.
Some TV models are equipped with the Network Search function. This greatly simplifies the question of how to set up digital television on a digital TV. Simply select the desired mode and continue by pressing the “Search” button.
Setting up on LG TVs
Now let's look at how to set up digital television on an LG digital TV. Considering that different TV models from a given manufacturer may have their own firmware and menu, you should not be immediately disappointed, since all models of the same company always have characteristic features. Therefore, it can be figured out quite easily. The step-by-step guide starts with the remote control and the “Menu” button on it. After clicking, select “Options” in the window that opens.
The “Options” tab presents several parameters, the most necessary of which will be the “Country” item. In this paragraph we indicate the country Germany or Finland.
Then you need to return to the “Setup” menu. We use the “Autosearch” item, in which we indicate the connection method “Cable”. Following all instructions in sequence will allow the TV to detect and tune in all available channels.
There is a small nuance that should be taken into account after setting up channels - the presence of a function, when turned on, the existing channel settings are reset and a new search begins. It is advisable to do without using this function. In the “Digital cable settings” tab, disable the option. After reading about what's on LG TVs and being a little careful, it's quite easy to tune the channels yourself.
Setup on Philips TVs
The instructions below will tell you how to properly set up digital television on Philips TVs.
Initially, we find the “Menu” button located on the remote control and enter the TV menu. The next step is to select the “Configuration” tab and enter this section. The window that appears will provide several options, one of which is the “Install” item. By clicking on this item, we call up a secondary menu on the TV screen. The required section is “Channel setup”. In the next submenu that appears, the necessary “Automatic installations” tab is required. As a result of successive correct transitions through the tabs, a message appears about the subsequent update of the list of available channels. Select the “Start” value.
After selecting the “Reinstall channels” item, the “Country” section follows. From the list of countries, as in the case of LG TVs, we select Finland or Germany. When selecting the connection method, select “Cable”.
If you understand how it was not difficult, you can proceed to searching for channels by clicking the “Start” symbol.
Setting up on Samsung TVs
The entire setup process is carried out directly by the remote control. By pressing the “Menu” button we call up the TV menu tab. In the “Channel” section, located under the image, the right side of the screen will open several tabs. In them we find the “Antenna” item and click on it, and in selecting the connection type we designate “Cable”. After going to the “Country” tab, select the “Other” option. As a result of the above actions, a window with the requested pin code will appear. The default pin code value is 0000.
In the “Auto Configuration” tab, the signal source will be “Cable”. After completing the sequential selection of tabs, you must click “Search”. The TV will certainly detect all channels currently available.
Setting up on Toshiba TVs
On Toshiba TVs, the entire setup process is greatly simplified. Go to the TV menu and select Russian. You need to find the “DTV Manual Tuning” tab. After entering the settings, click “Ok” and the determination of available channels begins.
Among other things, digital television is also available on a personal computer.