• Netgear N150 - overview of functions, self-configuration and firmware update. Netgear N150 - overview of functions, self-configuration and firmware update Advanced router settings

    Under the “N 150” brand, D-Link offers universal routers of the DIR-300 and DIR-300NRU models of one of their latest revisions. A solution in the form of a “100-Mbit” router, equipped with an additional “150-Mbit” Wi-Fi antenna, is well suited for building both home and office networks. Therefore, the D Link n150 router will be in demand, and the company will continue to update hardware revisions and firmware. Let's consider the option of setting up the basic functions of the device in a graphical interface with a “white and blue” design, a manual for which is currently missing on the official website.

    Router D-Link N150

    What does the combination “N 150” mean? Wireless networks, as we know, operate using one of three protocols: 802.11 B, or G, or N. The “802.11 G” protocol can provide a maximum connection speed of up to 54 Mbit/s, while “802.11 N” – up to 150 (this is when using one radio channel). Actually, the last option is implemented in the “N 150” routers.

    It is desirable that all subscriber devices in the Wi-Fi network can also work with the “N” protocol. But if this condition is not met, it will be enough to switch the router to “mixed” mode, and any device will be able to work in the wireless network (even using the now outdated “802.11 G” protocol). Let's start setting up.

    Setting up basic router functions

    Preliminary installation and connection steps

    Router DIR-300 with Wi-Fi 150Mbps

    On the back panel of the device there are four LAN ports (for connecting local computers, NAS drives, etc.), as well as one Internet port. The provider's cable is connected to the last port (the port is also called “WAN”).

    The setup is done in the web interface. Before setting up the router, you must make the following hardware connections:

    • In the “Internet” port – install the connector of the network cord from the provider
    • Any of the LAN ports – connect to a wired network card of the PC (using the patch cord included in the kit):

    Connecting the router to a computer for subsequent configuration

    • We do not turn on the power to the router now. You need to check that the wired connection is configured correctly:

    Setting up a network card on a computer

    • At the last stage, connect the power supply and turn on the router. In about a minute you will be able to enter the graphical web interface (when the device boots up).

    To enter the web interface, open a browser on your computer and go to the address: 192.168.0.1. The following image should appear on the screen:

    Main GUI tab

    Here, of course, you need to click on the “Manually configure” button. Next we will look at how to set up an Internet connection.

    Connection setup (DHCP option)

    If the provider “distributes” the Internet using the DHCP protocol, setting up a connection in the router will be easy. In the web interface you need to go to the “Network” -> “Connections” tab:

    Router connections tab

    Where you need to left-click once on the line that says WAN. A page will open where you can set connection parameters:

    Setting up a DHCP connection

    There is no need to configure anything additional for DHCP connections. If you plan to watch IPTV, check the “Enable IGMP” checkbox. If you need to change the MAC address, the new value must be set in the corresponding field (MAC). In the “Connection Type” list, in addition to “IPoE” (for us this is “DHCP connection”), there are three more options that must be considered separately. These are L2TP, PPTP and PPPoE.

    Having completed the necessary settings, click “Save” in the lower right corner of the page. The interface will return to the Connections tab. Check that the “Default Gateway” point remains on the connection that we configured (if there are several of them). Then you need to click “Save” in the upper right corner of the tab.

    A few seconds after saving the settings, the Internet connection will appear automatically. You can verify its presence on the “Status” -> “Network Statistics” tab:

    Device status tab

    Additionally, let's talk about setting up connections of other types (for example, PPTP). In this case, the IPoE connection should remain (you need to click the “Add” button and set the PPTP parameters). At the same time, even if the IGMP service is used, the IGMP checkbox is set only (!) in the IPoE settings, if necessary.

    Connections tab after PPTP setup

    Happy setup!

    Turn on Wi-Fi network

    Setting up a wireless network in a router is easier than any type of connection. On the “Wi-Fi” -> “General Settings” tab, the “Enable wireless connection” checkbox should be checked. To configure network parameters (name, etc.), you need to go to the next tab - “Basic settings”:

    Wi-Fi setup

    You need to do the following:

    1. In the “SSID” field – set the value of the network name
    2. “Country” – leave “default”
    3. “Channel” – radio channel number (from 1 to 13). It is recommended to use “auto” (then D Link n150 home router will turn on the least noisy one)
    4. “Wireless mode” – wireless network operating protocol, “N 150” or another. It's better to leave "B/G/N mixed". Only if all subscribers support working with “802.11 N”, to achieve the highest speed, you can select “N Only”.
    5. “Maximum number of subscribers” – here zero means “auto”.

    The last remaining setting is the “Hide...” checkbox. If you want to work on a hidden name, then install it. Finally, you need to click “Change” and wait for the tab to update. Then, in the upper right corner, click “Save”.

    Wi-Fi network protection can be set in the Security Settings tab:

    Setting up encryption on a wireless network

    A wireless network with new parameters will appear after rebooting the router. In the top menu you need to select the following:

    System menu at the top of the tab

    Saving with a reboot will allow you to immediately turn on the Wi-Fi network. Remember that the router will take about 1 minute to boot. Happy routing!

    Additional router features

    Setting up IPTV

    You can watch IPTV through a set-top box or through a computer connected to the router’s network. The setting option in both cases is different. Here we look at how to configure the D Link n150 router for broadcasting IPTV to a local network (viewing on a computer).

    First of all, in the Internet connection settings, you need to check the “Enable IGMP” checkbox. Moreover, it should be set only for “IPoE” connections. What was discussed above.

    However, that's not all you need to watch IPTV. There is a tab in the web interface called “IGMP”:

    IGMP Tab

    It is located in the list of "Advanced" tabs. And it contains one checkbox (“Enabled”, it must be checked), and a list of the version number (recommended “2”). Make settings on the “IGMP” tab, click “Change”, then click “Save”.

    After completing these steps, you can watch TV channels through your computer. All multicast packets (used in IPTV) end up in the local network.

    Question and answer

    Question: how does the D150L router of the Beeline operator differ from the D-Link N150?

    Hardware - nothing (this is one model). Programmatically, the firmware is configured “for the operator” so that the user only has to set a login and password:

    Beeline D150L router configuration interface

    Conclusion: one router is no better (no worse) than another. At the same time, the Beeline device does not need to be configured for the network of this operator. By the way, the interface address here ends with “1.1”.

    Question: How can I reset my router if I can’t open the interface?

    Turn on your device. Wait 2 minutes. Press "reset" on the back panel for 10 seconds. All indicators will flash 1 time. In a minute, you will be able to log into the web interface.

    And here we have configured the router for PPTP:

    Netgear N150 is one of the popular router models that is well suited for home use. Its throughput is small - 150 Mbps, but this is quite enough for the average user.

    The price of this router is also low, which makes it even more attractive. So, are you wondering how to start using Netgear N150? About all the intricacies of its connection and configuration below.

    Router equipment

    Netgear N150 comes in a lime-white box containing:

    • the router itself;
    • network cable;
    • power unit;
    • warranty card;
    • installation and use instructions;
    • disk with software for setting up the device.

    Pay attention! You will not find an antenna in the kit, since this model has a built-in one.

    On the front panel of the router there are LED indicators that reflect:

    • connecting the device to power;
    • Wi-Fi module activity;
    • Internet connection;
    • connection to a WPS network;
    • active LAN ports.

    Important! This model is cooled thanks to the grilles located on the body, so when installing it, it is necessary to choose such an arrangement so that they are not covered by other equipment and household items.

    The rear panel of the router is equipped with:

    • interfaces for connecting to the network;
    • power on/off switch;
    • four LAN ports for connecting additional devices to the local network;
    • WAN port to connect the device to an Internet service provider.

    Video: Wi-Fi router NETGEAR N150

    Connection

    After unpacking and familiarizing yourself with the components of the device, you can begin connecting it:

    • connect the power supply to the corresponding connector of the router and plug it into the network;
    • turn on the router by pressing the power button located on the rear panel;
    • find the WAN port and insert the Internet cable into it;
    • We connect the PC network adapter and any of the LAN ports using a special short cable provided in the kit.

    Having completed the physical part of the connection, we move on to its software part. It is necessary to configure the network card so that it allows you to obtain IP addresses automatically.

    Let's look at this process using the Windows 7 operating system as an example:


    This completes the connection and preliminary setup.

    Login to settings

    From now on, we will talk about how to set up a Netgear N150 wifi router.

    First, let's go to its interface:


    Internet

    Let's start setting up the Internet:


    Important! This method is suitable for providers with a static IP address.

    Connections via Dynamic IP

    If a dynamic IP is used for the connection (changing with each new session), then the process will be different:


    After these settings, access to the network will be open.

    PPPoE for Rostelecom, TTK and Dom.ru

    These providers are those who use a PPPoE connection - one of the most common types of network connections.

    Its setup is quite simple:


    Attention! The home ru provider uses MAC address binding, which means that it needs to make one additional amendment by specifying in the settings to use the address of the current PC.

    L2TP for Beeline

    L2TP is a fairly new connection type. It is used by such a popular provider as Beeline.

    For such a connection, do the following:


    WIFI Settings

    To set up a wireless connection, follow the following instructions:


    Pay attention! When setting a name for a new network, you need to take into account one important point - it is better to start it with a small letter in order to simplify the connection for some devices.

    IPTV

    You can connect the IPTV viewing function via an STB set-top box in a few simple steps.

    To do this you need:

    • go to the “Advanced” tab and select “Internet port settings”;
    • specify the local port to which the set-top box will be connected;
    • save the settings by clicking “Apply”.

    Video: NETGEAR N150 Wireless Router Unboxing

    Firmware update

    You can download the new firmware version and install it as follows:

    • remove the WAN cable from the router connector;
    • connect the PC to the LAN port of the device;
    • open the browser and enter “http://192.168.1.1”, press “Enter”;
    • in the interface that appears, enter the login information: login – “admin”, password – “password” (they can be found on the device itself or in the instructions);
    • Click on the current firmware version number located at the top of the page;
    • A file download window will appear, indicate the directory on the computer where it will be saved;
    • click “Submit” and start the installation process;
    • We wait for it to complete, after which the router will automatically reboot.

    Attention! During installation, do not turn off the power or disconnect cables.

    In some cases, when it is not possible to go to the web interface (for example, when the router has already been in use), it is necessary to reset the router settings to factory settings.

    This is done like this:

    • There is a reset button on the back panel, find it;
    • using a pen or paperclip, hold it for 10 seconds;
    • the indicators on the device will blink and the router will reboot, restoring the default settings;
    • go to the menu using standard data.

    Important! It is important to keep in mind that when you return to standard settings, all external devices, even those that do not belong to you, will be able to connect to the network. You can correct this situation in the settings menu by setting a password for entry.

    You will notice that the setup of the Netgear N150 is practically no different from similar models. The whole process is completely doable at home and does not require the skills of an “advanced” user.

    Netgear N150 is a classic router model for home use without unnecessary bells and whistles. The device is attractive in price and appearance, and copes well with the everyday tasks of Internet users. Let's find out what the main characteristics of this router are and how to configure it to work on the network, and, if necessary, change its firmware.

    Inexpensive router with high transfer speeds

    This model, in terms of its characteristics, is a fairly typical device at a reasonable price, which does not affect the high quality of the connection. The highest data transfer speed in the model is about 150 Mbit/s, which is enough for home use. You can create a local network thanks to the presence of 4 LAN ports for connecting several users via cable; Wi-Fi is used for wireless signal distribution.

    The router provides a good signal over a fairly large area, is easy to use, and has a pleasant and simple interface, which we will look at later.

    Installing Internet on Netgear N150

    After connecting the network equipment to the PC, check the network system settings - in the connection properties, open Internet Protocol number 4, set automatic detection of IP and DNS.

    The router is directly configured through its menu, which can be opened in a browser - you must enter the combination 192.168.1.1 in the address bar. and enter the words “admin” and “password” in the login and access key fields.

    To set up a connection that works via Dynamic IP, you need to do the following:

    • Select the “Installation” section, which will cause the main parameters window to appear.
    • When asked if you need to enter additional data to establish a connection, answer “No”.
    • Next, select the “Obtain automatically from your service provider” option next to configurations such as IP and DNS.
    • What should you choose in the settings when it comes to using the MAC address? If the provider uses a binding, select “Use this computer’s MAC address”; if not, select the default setting.
    • Don't forget to click "Apply" for the changes to take effect.

    To use the Internet via Static IP, you should follow the same steps with one difference - instead of automatically determining IP, DNS, enter the data specified in the contract from the supplier.

    Network setup using PPPoE, PPTP, L2TP

    For a connection via the PPPoE protocol, the following parameters are defined:

    • Open the “Installation”, “Basic Settings” menu.
    • When asked if additional data needs to be entered, we answer “Yes”.
    • In “Internet Service Provider”, select the required protocol.
    • Enter the username and password from the agreement and save the changes.

    An L2TP or PPTP connection is established as follows:

    • Select the answer “Yes” to the first question from the form in the “Basic section settings” menu, “Installation”.
    • From the drop-down list, determine your Internet service provider by specifying one of the protocols.
    • Enter the user name, the key from the data you provided from the provider.
    • Enter the required combination in the “Server Address” line - you will find it out by reviewing the Internet service agreement.

    Activating the Wi-Fi module

    When you have completed the network setup, you can proceed to activate Wi-Fi, which is done this way:

    • Go through the router menu to the “Wireless Connection Settings” section.
    • In the SSID line, create your network name.
    • Select the country where you live.
    • In the encryption type selection menu, select WPA2-PSK, as it is the most reliable among the others.
    • In the last field, create a password consisting of a complex combination - preferably it includes not only numbers, but also letters.

    Software update

    Changing the firmware on the Netgear N150 router is quite simple - first of all, download the file with the new firmware from the developer’s official website, then follow these steps:

    • In the “Settings” menu, open the “Maintenance” section, “Router Update” submenu.
    • In the window that appears, specify the path to the firmware file, then select “Download”, and the device will update, then reboot.

    There is another way to update the firmware - in the same menu there is a “Check” button, thanks to which the router will independently search for firmware on the World Wide Web and also install a new version.

    As you can see, the Netgear N150 has excellent characteristics, is very easy to set up and use, and will provide you with a high-quality high-speed connection. If necessary, you can always easily change its settings, thanks to the clear menu interface, or install new firmware for the correct operation of the router.

    The Netgear N 150 router uses the common 802.11g/n wifi technology. The operating frequency of the Wi-Fi transmitter here is 2.4 GHz, and the data exchange speed over the wireless channel is up to 150 Mbit/s.

    You can also simultaneously connect up to 4 wired devices to the device (desktop computer, printer, IP-TV set-top box, etc.).

    In addition, it provides a very useful double firewall function for the router (which will protect the home network from unwanted “visits” from the outside), as well as protection against DoS attacks.

    Unfortunately, clear instructions in Russian do not always accompany this Wi-Fi router, so here we will look at how to connect and configure the netgear n 150 wireless router yourself.

    Netgear n 150 router: review and brief description

    Externally, the device is a compact plastic “box”, which, when installing the device, can be fixed in two positions using a special stand included in the basic configuration of the router.

    On the front panel there are indicator lights:

    • - Nutrition
    • - WPS status (more information about the WPS function can be found in the article)
    • - Wi-Fi status
    • - Internet connection (if this indicator is not lit, you should contact your provider’s support service: there may be problems “on the line” or the service for this subscriber has been temporarily suspended)
    • - 4 indicators characterizing connected wired devices.

    On the reverse side are:

    • - Antenna for Wi-fi.
    • - Power button.
    • - Power connector.
    • - Connector for connecting to the Internet.
    • - 4 LAN connectors for connecting wired devices.

    The sidebar also has buttons:

    • - WPS on/off button
    • - Wi-Fi on/off button

    How to connect a Netgear N 150 router?

    To independently connect the netgear n 150 router to the Internet, you will need a cable provided by your Internet provider and an outlet to connect the device to a 220 V power supply.

    First, connect the power adapter to the back of the router, and plug the other end into a power outlet, then press the power button.

    At the same time, the power indicator on the front panel of Netgir should light up. As soon as it glows steady green, the router is ready for use.

    To configure the router for the first time, you need to connect the device to your computer using a network cable. In this case, the LED corresponding to the occupied LAN connector should light up on the indicator panel.

    If this Netgir router has ever been in use, you should first use the Reset button “recessed” into the body on the back panel of the device.

    How to configure Netgear N150 router?

    After physically connecting to your PC, you can access the router settings through any web browser installed on your computer.

    To do this, enter the address http://www.routerlogin.net/ or http://www.routerlogin.com/ directly in the address bar and press the Enter (or “go”) key.

    If this address does not respond, use the static IP address of the router indicated on the service label of the device. In most cases, this is the combination 192.168.1.1

    After this, a registration window will appear, where you should specify the login and password to enter the settings of the netgear n 150 router: by default, these are admin and password, respectively (the data should be entered in capital letters).

    If at this stage you are asked to search for software updates for the router, it is recommended to agree with the router’s offer.

    For quick setup, select the Setup Wizard or Setup Wizard option in the left menu and agree to the wizard’s suggestion to automatically recognize the network - setting up an Internet connection is complete.

    For manual configuration, refuse the auto-configuration offer and go to the “Settings” -> “Basic Settings” section, then check from the contract with the provider (or in the 24-hour support service) the method provided to you for connecting to the Internet and whether it is required to indicate when connecting to the World Wide Web login/password.

    When dynamically obtaining an IP address, the following settings will appear here.

    With PPPoE connection (for Internet providers Rostelecom, Dom ru, etc.)

    Netgear N150 router: how to set up WiFi?

    Now let's figure out how to set up wireless Internet.

    To enable this function, press the Wi-Fi button on the side panel of the device.

    From your computer, in the main menu of the router, select “Wireless settings” or “Wireless connection settings”.

    You can then enter your wireless network security settings.

    How to change the password on the netgear N150 router?

    How to disable WPS on Netgear N150 router?

    Click the WPS button on the side panel of the device, or the soft button in the router settings through the browser, and the router will continue to operate in unprotected mode.

    Read more: