Keyboards and mice for a desktop computer. Rules for connecting a keyboard to a computer

I think no one will deny that the popularity of tablets for Lately has grown a lot and many users cannot even imagine their work without this gadget

But tablets have (in my opinion) a significant drawback: if you need to write something longer than 2-3 sentences, then it becomes a real nightmare. To fix this, there are small wireless keyboards on the market that connect via Bluetooth and allow you to close this shortcoming (moreover, they often come with a case).

In this article, I wanted to take a look at the steps on how to set up the connection of such a keyboard to a tablet. There is nothing complicated in this matter, but as elsewhere, there are some nuances ...

1) Switching on the keyboard

The wireless keyboard has dedicated buttons for enabling and configuring the connection. They are located either a little higher above the keys, or on the side wall of the keyboard (see Fig. 1). The first thing to do is to turn it on, as a rule, the LEDs should start flashing (or lit).

2) Setting up Bluetooth on the tablet

In the settings, you need to open the section " Wireless networks"And turn on the Bluetooth connection (blue switch in Fig. 2). Then go to bluetooth settings.

3) Selecting a device from the available ...

If your keyboard is turned on (the LEDs on it should blink) and the tablet starts looking for devices available for connection, you should see your keyboard in the list (as in Fig. 3). You need to select it and connect.

4) Pairing

The pairing process is the establishment of a connection between your keyboard and tablet. It usually takes 10-15 seconds.

5) Password for confirmation

The final touch - on the keyboard you need to enter the password to access the tablet, which you will see on its screen. Please note that after entering these numbers on the keyboard, you need to press Enter.

6) Completing the connection

If everything was done correctly and there were no errors, then you will see a message that the bluetooth keyboard is connected (this is the wireless keyboard). Now you can open notepad and type from the keyboard to your heart's content.

What to do if the tablet does not see the bluetooth keyboard?

1) The most common is a dead keyboard battery. Especially if you are trying to connect it to a tablet for the first time. Charge the keyboard battery first, and then try connecting it again.

2) Open system requirements and a description of your keyboard. Suddenly it is not supported by android at all (pay attention also to the android version) ?!

3) Yes special applications on "Google Play", for example "Russian Keyboard". By installing such an application (it will help when working with non-standard keyboards) - it will quickly fix compatibility problems and the device will start working as expected ...

Connecting a keyboard to a laptop (Windows 10)

In general, connect additional keyboard a laptop is required much less often than a tablet (after all, a laptop has one keyboard

). But this may be necessary when, for example, the native keyboard is flooded with tea or coffee and some keys do not work well on it. Consider how this is done on a laptop.

1) Switching on the keyboard

Similar step as in the first section of this article…

2) Does Bluetooth work?

Very often, Bluetooth is not enabled at all on a laptop and drivers are not installed for it ... The easiest way to find out if it works wireless connection- just see if there is this icon in the tray (see Fig. 7).

Delivery of drivers in 1 click:

3) If Bluetooth is turned off (for whom it works, you can skip this step)

If you have installed (updated) the drivers, then it is not a fact that Bluetooth works for you. The fact is that it can be turned off in the Windows settings. Let's see how to enable it in Windows 10.

First, open the START menu and go to the settings (see Fig. 8).

Then enable bluetooth network(see fig. 10).

6) Well done

The keyboard is connected, in fact, you can work behind it.

7) Verification

To check, you can open any notepad or text editor- letters and numbers are printed, so the keyboard is working. Q.E.D…

That concludes, good luck!

Technology developers always strive to achieve one goal - to increase the convenience and comfort of a person. is no exception. The weight and dimensions of laptops have decreased, routers have made it possible to access the Internet without eternal problems with connectors and cables, the examples are almost endless. Let's talk about one of these know-how in more detail. It's about setting up and connecting a wireless keyboard.

When buying a new wireless keyboard, keep in mind that there should be three things in the package. The first of these is the keyboard itself, the second is the driver disk, the last is the wireless adapter, which connects via a USB port and works on the "Bluetooth" principle. Sometimes this set may include several batteries, but often they have to be purchased separately. Rechargeable batteries are perfect for this purpose, although they are quite expensive, but unlike conventional ones, they can be charged, and they also hold a charge much longer. In addition, there are kits on sale in which there is also a mouse. However, it all depends directly on the manufacturer and price. So, let's proceed directly to the installation. First, insert the disk containing the drivers into the drive, and as soon as it starts up, a menu should appear. But if nothing appears automatically, then you need to start it manually. To do this, go to the standard Explorer "Computer" or "My Computer" if you are using the "Windows XP" operating system. Next, double-click the left mouse button on the drive icon and in the window that opens, find the file called "Install.exe" or "Setup.exe". Run it - and you can start connecting the keyboard to the computer.

Now you need to connect the wireless adapter to the USB port. By the way, sometimes such connectors are equipped with an LED to simplify perception, which will start flashing when the connection with the keyboard is established. If there is any problem, the light bulb will not work. And if you have already connected a laser bear before, then this experience will help, since the installation is similar.

Next, you need to insert the batteries. Their installation does not require enchanting knowledge, and we hope that you can do it yourself. If the keyboard does not work, turn it over and examine it carefully back cover, it should have a switch in the form of a small lever. It should be switched to the “ON” position, this should turn on the power of the product. Next, a message will appear on the desktop that the system has detected a new device, and Windows will automatically install the drivers from the previously launched disk. When the setup is complete, restart your computer and you can use the keyboard.

And if you have problems with the BIOS system, you will have to abandon the idea. Take out the keyboard with ordinary cable, since the old ones do not support USB adapter settings, and the Windows driver itself is not included.

The Bluetooth keyboard communicates with the computer via a Bluetooth transceiver.

If your keyboard does not have a Microsoft Bluetooth transceiver, you must connect it using your computer's built-in transceiver (non-Microsoft) and your computer's Bluetooth configuration software.

• If your keyboard has a Microsoft transceiver with a First Connect button, you can use it to launch the Microsoft Connection Wizard. It will help you establish a Bluetooth connection.
• If your keyboard has a Microsoft Bluetooth transceiver without a First Connect button, you must connect the transceiver and then connect the device using the Bluetooth setup software on your computer.
• If your computer has a built-in third-party transceiver, you can connect the device to your computer directly using the configuration tool software Bluetooth on a computer, but without using a Microsoft Bluetooth transceiver.
• Note. The power button on newer devices with Bluetooth technology, such as the Wedge Touch Mouse and Sculpt Touch Mouse, must be pressed and held for about 5 seconds to pair the device with the computer.

Using an access key

The passkey must always be set when connecting a keyboard or numeric keypad to the computer. The method for setting the access key depends on Bluetooth programs on the computer. If your Bluetooth software offers different ways to create a passkey, let it generate the passkey automatically instead of setting it yourself or not setting it at all. When you enter a passkey, it will not be displayed on the screen. After entering the access key, press the key ENTER on the keyboard or numeric keypad to complete the connection.

Connecting a keyboard using a Microsoft Bluetooth transceiver with a First Connect button

Some Bluetooth keyboards have button transceivers that make it easy to connect your device to your computer.

1. Connect the Microsoft Bluetooth transceiver to the USB connector.
2. Press and hold the Connect button on the USB transceiver for five seconds. The Microsoft Connection Wizard appears.

1. Launch the Microsoft Mouse and Keyboard Center.
2. Select a Bluetooth keyboard that uses a transceiver with a First Connect button.
3. Click the tab and click the Connect button.
4. Follow the wizard instructions to connect the device.

Connecting a Bluetooth keyboard without a First Connect button

At Keyboards Elite for Bluetooth and Wireless Optical Desktop for Bluetooth do not have a First Connect button on the transceivers. additional information To connect these keyboards to your computer, see the Bluetooth pairing guide or the documentation for your Bluetooth software.

Connecting a keyboard without a Microsoft Bluetooth transceiver

If your computer has a built-in Bluetooth transceiver, you can use it to connect a keyboard without using a Microsoft USB transceiver.

Attention!

When connected using a third-party Bluetooth transceiver, some advanced features of the Mouse and Keyboard Center may not work. The Mouse and Keyboard Control Center is designed to work with Microsoft Bluetooth software. In most cases, Toshiba Bluetooth software will be an equivalent replacement. Other Bluetooth software may work but is not supported.

1. Open the Bluetooth program on your computer. It's usually found in the Control Panel or Options menu.
2. From the bottom of the device, remove the battery cover and set the switch to Bluetooth mode.
3. To reconnect your device to your computer, press and hold the Connect button on the bottom of the device for a few seconds. If the indicator light on the top of the device flashes green and red, the device can be detected by other Bluetooth devices within 2 minutes.
4. After the mouse appears in the list, select it and follow the instructions to successfully connect the device.

Note.
The name of a specific command in different Bluetooth programs and different versions may differ slightly.

Starting the Bluetooth program

There are several versions of Bluetooth software that allow you to connect your device to a Bluetooth wireless transceiver. For information about using the program, see your computer's documentation or contact its manufacturer.

Equipment

Location of the Bluetooth program

For some Windows 10 PCs

Sequentially select Start > Settings > Devices > Bluetooth

For some PCs with Windows 8.1

Sequentially select Charm > Settings > Change PC settings > PC and devices > Bluetooth

For some computers with Windows 7

Press the start button, select Control Panel > Equipment and sound > Bluetooth devices.

If you for a long time used a desktop computer, then after switching to a laptop, you may notice that separate keyboard It is more convenient to use than the built-in laptop. Experience has shown that the inconvenience increases even more as laptops get smaller and with it new typing restrictions. At the same time, you have to sacrifice digital block and some auxiliary keys, combining them with others.

If you find all these changes unacceptable and your typing speed has dropped dramatically, then a wireless keyboard should be your choice. With it you get all the benefits of a keyboard standard sizes, while maintaining mobility, thanks to wireless interface. Next, we will show you how to connect such a keyboard to a laptop.

Instruction

radio keyboard

1. First, make sure your laptop is compatible with these wireless technologies like Bluetooth or RF (radio frequency). Purchase a wireless keyboard that supports the wireless interface found in the laptop.

2. Before connecting the keyboard, make sure that the radio modules of the keyboard and laptop are not closer than eight inches to sources of interference, such as: computer monitor, processor, metal objects, electric fans, fluorescent lamps, etc. At the same time, it is desirable to provide direct visibility between connected devices, eliminating all sorts of obstacles.

3. Turn the keyboard back up and open the battery compartment. Install batteries in it. The need for autonomous power is due to the fact that the keyboard is not connected by cable to the computer. Check that the batteries are installed with the correct polarity.

4. Insert the driver on the CD that comes with the keyboard into the laptop's drive and follow the instructions to install the driver along with the control application.

5. Insert the nanoreceiver (miniature transceiver) into a free USB port on your laptop. If you don't have a free port, use USB hub to expand the number of ports.

6. After that, the laptop will start configuring the keyboard driver. Wait until the end of the process. At the end, you will receive a message indicating that the keyboard is set up and ready to use.

7. Check that the keyboard works by opening a document and typing a test message while using all the keyboard keys (numbers, letters, function keys). Check the reaction to pressing "Caps Lock".

Bluetooth keyboard

1. If your laptop has a module wireless communication Bluetooth 2.0, then the installation will be somewhat easier. Download the wireless keyboard driver to the system.

2. Activate bluetooth module by clicking on the special button (see the manual for the laptop) and wait for the installation to complete. When the button is pressed (the indicator is active), your laptop will be able to connect to the keyboard.

3. Right-click on the keyboard icon on the desktop and select the Pair the Device wireless keyboard connection option. Follow the prompts until the keyboard is ready for use.

Conclusion

If the keyboard does not work, check for physical and radio interference on the path between the radio modules. Move sources electromagnetic radiation away. If this does not help, refer to the troubleshooting section of the keyboard manual or contact the manufacturer's support service.

The computer is a complex machine. It can be connected to many additional devices. For example, a mouse or keyboard. These are extremely important components that allow you to comfortably work with the operating system. Next, we will talk about how to connect a keyboard to a computer. In fact, understanding this is not as difficult as it seems. But users should be aware of some of the features of the process, since it is not always possible to connect the keyboard to the desktop computer or laptop. So what should you pay attention to?

different models

The first and most important point is to determine the type of keyboard that will be connected. To date, there are several models of these devices. The type of component selected will determine how to connect the keyboard to the computer.

You can find the following connection connectors for keyboards:

• PS/2;
• bluetooth.

So how to act in this or that case? What connection features should each user be aware of?

Not always possible

For example, sometimes it turns out that one or another keyboard model cannot be connected to a computer. Usually in this case, a PS / 2 connector is implied. Why?

The thing is that the corresponding socket for connection is available only on stationary computers. Netbooks, laptops and ultrabooks do not have these connectors. Therefore, it will not work to connect the corresponding keyboard. Although there are some tricks that can help resolve the situation.

However, the user must take into account that not all keyboard models are always connected to computers. Sometimes the reason for the failure of the corresponding component to work is non-compliance with system requirements. You will have to pay attention to them before buying an I / O device.

Connecting old keyboards

How to connect a keyboard to a computer? PS/2, for example? Such keyboards are considered old. And so some modern users don't know how to act.

To connect a PS/2 keyboard to your computer, you need to:

1. Locate the PS/2 connector on the back of the computer. It represents a round hole with 6 legs and a lock.
2. Insert the keyboard wire into the appropriate connector.
3. Turn on the computer or wait until the device is detected by the operating system.

It is important to note that the mouse and keyboard connectors on the PS/2 models look the same. Their only difference from each other is the different color of the nests. Therefore, it is important to properly connect input devices. Most often, there is a keyboard miniature near the corresponding slot. You can connect both when the system unit is turned on and when it is turned off.

Through an adapter

How to connect a keyboard to a computer? PS / 2 can also be connected to the USB connector, but for this you will have to try. Many users do not see any point in this. The fact is that in order to successfully translate ideas into reality, you need to purchase a special adapter. It will have a PS/2 socket on one end and a USB socket on the other. That's the only way to do what you want to do.

How to connect a keyboard to a computer? If you want to connect a PS/2 model via USB, you need:

1. Buy a special PS/2-USB adapter.
2. Put the adapter on the PS/2 connector.
3. Find a USB socket on your computer and plug the keyboard with the adapter into it.
4. Power on or reboot operating system.

Nothing difficult or special. After connecting the keyboard, you will have to wait a bit. The device may not start working immediately, but after a few minutes. This is normal. During this period, the keyboard drivers are searched for and installed. Once the appropriate software is installed, you can use the input device.

Via USB

The most popular and common type of keyboards is USB. Since similar devices users work most often. How to connect a keyboard to a computer? To do this is not so difficult.

To use the USB connection, the user must:

1. Find a USB port on your computer or laptop. This is a rectangular socket on the panel. Each computer has several.
2. Plug the device connection cable into any of the USB connectors.
3. Turn on or restart your computer.

Then you have to wait for the drivers to be installed. If automatic installation did not occur, you must install the appropriate software yourself. It is either downloaded from the official website of the keyboard manufacturer, or supplied as a kit to the connected device. Driver installation takes only a few minutes and resembles initialization regular application for PC.

Without wires

How to connect wireless keyboard to a computer? This question interested in many users. After all, wireless computer components appear in stores more and more often. There is nothing difficult in this. It is enough just to follow a small instruction.

So, how to connect a wireless keyboard to a computer? To do this, the user must:

1. Insert the battery into the keyboard and set the device status to "On".
2. Plug a special USB receiver into the USB connector.
3. Install drivers for connected equipment. You can carry out this venture later. The software CD is included with the keyboard.
4. Synchronize your device with your computer. To do this, you need to go to the program installed with the drivers, and then select the appropriate equipment from the list that appears.

This is all. In fact, the connection is not so difficult. In some cases, it is enough to simply insert the battery or batteries into the keyboard, then turn on the USB receiver and restart the computer. But there is another scenario.

Without receiver

This is a connection without a receiver. Pretty common way to do it. How to connect a wireless keyboard to a computer without a USB receiver?

To do this, the user must:

1. Insert the battery into the input device. Sometimes batteries are needed to turn on.
2. Switch the device to "On" mode.
3. Turn on Bluetooth on your computer.
4. Find a keyboard and sync it with the machine.
5. Wait for the drivers to install. Sometimes you need to install the appropriate programs on your computer yourself.

Now it’s clear how to connect the keyboard to the computer in one case or another. As you can see, even a novice user can cope with the task.

Recently, the laptop is gaining great popularity in the field of computer sales. After all, it is a compact and wireless version of your desktop computer. The list of its amenities does not end with small dimensions and ultra-lightness. Among all the advantages of a laptop, there are also disadvantages. This is a short time without a network, a small power of the video adapter. Some laptop users are not happy with the flat keyboard buttons. They come to the aid of a standard 101-key keyboard with the ability to connect to a laptop.

You will need

• Standard keyboard, PS/2-USB adapter.

Instruction

When buying a laptop keyboard, pay attention to the connector with which it will connect to the device.

The keyboard is required with a standard USB connector.

You just have to connect the keyboard to the desired USB port on the laptop (on the right or left in the laptop, usually) and after the new device is detected by the laptop, you can safely get to work.

I myself always use an additional keyboard that is connected to my laptop.

I will only say one thing, when moving away from the laptop's eyes, because the keyboard is installed in front of it, a person can spoil his eyesight a little. The letters are small and far away. There is an adaptation of the eyes to this, and if long time so to work, small letters on the packaging of goods will be difficult for you to read. That's exactly what happened to me.

Connecting a keyboard to a laptop is very simple and does not require any additional programs. all that is needed is the presence of a USB connector, which is present in all models. Connect the keyboard through this connector and you can get to work.

This is the simplest action, all laptops have USB connectors, when buying a keyboard, you should ask if it has them.

If there is something you buy and connect, everything will be set up by itself and you can work.

There is nothing easier, but there is one condition - your laptop must have a USB connector. I strongly doubt that there are now such laptops where this device is not. Moreover, you can still connect a monitor and work will be even more comfortable!

The laptop only has a USB input. Therefore, the keyboard must also be selected with a USB connector. Moreover, if you buy wireless model keyboards, the kit often includes wireless mouse. With such a purchase, you can kill two birds with one stone: both the keyboard and mouse will be wireless, and only one USB input will be occupied in the laptop.

The fact is that old keyboards have a different connector, of blue color, round. But it cannot be connected to a laptop.

I am using a wireless keyboard. USB connection, as always. You can also connect a mouse - even more convenient

There is nothing easier than connect keyboard to laptop. To do this, you need any of them, with USB output, and these are everywhere and they are the most common.

My child spilled water on the laptop, the keyboard stopped working. Connected another and enjoyed quietly. And then the old one started working.

Connecting a keyboard to a laptop is not a big deal. You just need to stick usb wire in a laptop slot. Everything will automatically work.

There are also wireless keyboards, they are even much more convenient to use.

Basically, to connect a keyboard to a laptop, just pick up a keyboard with a standard USB connector.

Further, to connect a keyboard to a laptop, insert the connector into a free USB port on the laptop and wait for the computer to find the keyboard driver. As a rule, after that, a message appears below that the keyboard is ready for work.

If the laptop did not find the keyboard driver on its own, you need to enter the Control Panel, then Device Manager, then find the keyboards and right-click on the keyboard. After that, it remains only to click on the inscription Update driver and complete the installation of the keyboard.

I read your question a few days ago and was very interested in it, since some keys on the laptop stopped working. Thought it would come new laptop buy. But I read the answers and realized that the sun is not so bad. Bought today Jet A wireless ultra compact keyboard(without a mouse, which suits me perfectly: I'm used to not working without it). I connected the keyboard without any problems, putting the USB nano-receiver in the right slot, and already on it, and not on virtual keyboard, typed this answer :-) Thank you all very much for the answers: it was real help received by me on BV!

Hello everyone, do you know how to connect a keyboard to a laptop. Cases are different. The level of computer use in people is different, and if someone uses it from early childhood, then someone is just starting to master computer basics and so the question is: how to connect keyboard to laptop remains open. You know, there is such a need to work on a laptop, but only on a regular keyboard, and not on a built-in one. How to charge a laptop will be discussed in other articles.

Why you need to connect external keyboard. Many people find it inconvenient to work on the built-in keyboard, they want to adjust, change the height, and adjust the work process for themselves. Or it happens that you want to learn how to type quickly, start to actively train, and with a good speed, you can damage the built-in keyboard, and its repair, of course, will be more expensive. Therefore, it is recommended for active use connect an external keyboard, because if necessary it can be quickly replaced.

In order to connect an external keyboard to a laptop, it is important to read the instructions to find out if an additional driver is required. Why this is important - the answer is simple - the plug-in keyboard will not work correctly. And if there is a disk, then first we install the driver responsible for the work multimedia capabilities keyboards. Insert the keyboard cord into USB connector, if everything is done correctly, then the keyboard should work. If the connection is not observed, then you can reboot the system, recall, start - shutdown and reboot. When the laptop turns on, the keyboard should work.

If the instructions do not indicate a driver, then this keyboard can be connected to a laptop without installing additional software. This is the most common connection option. We put the USB cable into the connector - and the process of connecting the keyboard begins. To be safe, reboot.

What to do if the keyboard is not connected to the laptop? And what can be done here. There is only one reason - the keyboard does not work, it is better to buy another one. There is an option to take the laptop to the store and see on the spot how to connect the keyboard to the laptop. At USB connection The cable must not be plugged into the connector forcibly, as this may damage it.

Some points for connecting a keyboard to a laptop

In order for you to be able to connect the keyboard to a laptop, you should make sure that it has the appropriate usb interface, and not ps2. Just when you come to a computer store, then ask for a usb keyboard. Read more about laptop keyboards here. Also choose a mouse with a USB cable, they cost a little more, but they are connected to a laptop. Plug the cable carefully so as not to loosen the socket, because then it will not connect well.

There are also wireless keyboards for laptops. They connect a bit via bluetooth. In this regard, those people who have a built-in adapter in their laptop are lucky. If not, then you should also buy a Bluetooth adapter, which will connect to the keyboard. By the way, if you connect an external keyboard, both will work fine, which allows you to play some games together. If the keyboard does not work, then the driver has probably not been installed. Therefore, it is worth using the instructions.

Can I add a keyboard to my laptop?

Windows 7 - so smart system, which allows you to act as you see fit. Connecting the keyboard is a very simple and easy task that everyone must handle. What's more, there are many keyboard options on the market that are equipped with a USB output, and the laptop itself has more than 3 slots. The only thing to remember is that if you often connect and disconnect the keyboard, then these sockets become loose, and as a result it will be difficult to work with them, especially since we are talking about a laptop, and its repair is more expensive. All usb keyboard equipped with a Plug & Play function, which translates as “plug and play”. If the keyboard is multimedia, then install the drivers, if we are talking about simple keyboards, then Windows 7 itself will update and connect everything.

To connect the keyboard to a laptop, you need a cable and drivers. If you have wireless device, then make sure that the radio module is available in the kit. It is necessary to connect an additional keyboard for convenience or in case of a malfunction of the built-in one. When buying new equipment, instructions for connection must be present. If it is not there, you can read the methods for connecting the device in the article.

How to connect a keyboard to a laptop

The most popular way to connect a keyboard is to connect it via a USB cable. Usually, drivers are already built into the operating system, but they are easy to download on the Internet. Also, on older laptop models, it is possible to connect the keyboard via PS / 2, this method is outdated, but still works.

You must use only devices that are compatible with the laptop and OS. Otherwise, the equipment will not work correctly or even break down. The wireless keyboard has many advantages, it is very convenient to work with it, you just need to insert the USB radio module.

If the keyboard is not detected, you should open the Task Manager and find the keyboard in the list of connected devices. She will glow Exclamation point. Double-click on the icon with the left mouse button and click "Update" in the window that appears. Then choose automatic installation and wait until the system finds itself required drivers on the Internet and install them.

What to consider when connecting a keyboard to a laptop

Look at the box of the device with what equipment it is compatible with, system requirements. If everything is fine, then connect it and wait for the drivers to be installed, a notification should appear that it is ready for use.

Check for a battery in the remote keypad. The equipment is switched on with a switch. Drivers are installed only once, so the next time you connect the device, it will work right away. If the equipment does not work, you can contact standard procedure troubleshooting.

You can connect not only a wireless keyboard to a laptop, but also a mouse with a monitor. Then you can use your device at a distance of several meters. On average, the connection takes no more than a few minutes.