Shift doesn't work, what should I do? Shift button not working on laptop

Question: Asus X552C - The keys on the laptop do not work

Answer: Well if they exist Trojans, which determine which buttons the user pressed and send this to the owner, but there may also be viruses that block signals from the buttons.
But in practice this has not been seen.

Question: Keys on laptops have stopped working

Answer: Spammer116
Open the keyboard, clean it from dust and dirt, find the keyboard contactor with the M-board and clean the contacts.
Ethyl alcohol or aka + PURE gasoline (not “for lighters”, but “for cleaning clothes”; sometimes this is called NEFRAS or ISOOCTANE)

Good day! There is a problem. On the above laptop, the keys on the numeric part of the keyboard (located on the right) stopped working. When you press the key. " num lock"no reaction, the LED does not light up. The rest of the keyboard and the laptop as a whole work fine. The saddest thing is that even in the BIOS the arrows on keys "4,6,8,2" do not work, the function of increasing and decreasing the volume does not work either it works. To avoid wasting my and your time, I’ll write right away: I changed the keyboard to a known working one, flashed the BIOS, all operations in Windows (for example, such as turning on via virtual keyboard etc. etc.) done, no result!!! I checked the connector for the standard keyboard and everything is fine. But there is one BUT!!! When connected USB keyboards On this keyboard everything works as it should, even in the BIOS. Please speak out. Thanks in advance.

Answer:

alertwer wrote:

Didn't understand. If the cartoon works, should it ring the same or not?

If it rings the same way, then the lines from the multi to the connector are normal - not on a break, not shorted - with normal insulation, etc., and if not normal, then everything is the other way around, including maybe because of the multi, there is a problem.

Question: The cooler on the laptop does not work

Answer: They tried to solder the mother, but it resulted in the laptop turning off after exactly 30 minutes of operation, so they decided to replace the mother, but the processor was told that it had burned out and there was no way I could check it

Question: The touchpad does not work on an ACER laptop

Hello, why might the touchpad on a laptop not work?

Added after 28 seconds

I've searched the entire Internet and haven't really found anything, it's something similar to my problem, but even my power button doesn't work... help, I urgently need a PC!

Added after 1 minute

Very urgent! I need a faster computer. Does anyone know what's wrong?

Answer: Hello, the touchpad doesn't work acer aspire es1-512 works exactly under 8.1, under 7 it works without problems. I tried all possible firewood - it doesn’t help. there is hope for you. Yes, it doesn’t show up in the manager

Question: Both Shift keys on the laptop do not work

Answer:

Message from FavoriteFeed

On the cable I saw one contact, slightly different from the rest.

Message from FavoriteFeed

But I assure you that the laptop is kept away from any liquids and no one sat down with it with tea. Otherwise I wouldn't be writing on the forum.

Can you take a photo (in quality) of this train?

You can often see users complaining that “Shift” on their keyboard does not work. This phenomenon is not so rare. It can be caused by various reasons. Nevertheless, this scenario causes a lot of problems for users. Sometimes even typing text becomes very problematic.

So what if "Shift" refused to work? Why does this happen? Is there any cause for concern? Answering all these questions is not as difficult as it seems. The most important thing is not to panic. After all, the problem being studied is not always critical. Moreover, only in rare cases, when the Shift button fails to work, do you have to take drastic action.

Keyboard problem

The first reason is obvious. It occurs quite often, but it manifests itself not only in the fact that “Shift” on the keyboard does not work. The point is that all equipment can wear out. It is likely that the failure of the specified key to work is a consequence of a malfunction of the connected device. What should I do? You can either install new keyboard and check the functionality of the specified button, or try to repair the old one. As practice shows, the first method of solving the problem is the most effective. What's next?

Blockage

Is the Shift button on your keyboard not working or sticking? More precisely, is it not pressed the first time or does the computer basically not respond to this key? Then you should clean the keyboard. This phenomenon should not be scary. After all this problem occurs often, especially if a person is used to eating right in front of a computer or laptop.

What's the matter? In the most common blockage. Every keyboard needs to be cleaned from time to time. Otherwise, its buttons begin to refuse to work. Including Shift. Therefore, users quite often advise each other, if any problems arise with the keyboard, to disassemble this component and clean it. Surprisingly, this method very often helps to get rid of problems that have arisen. But even on this possible reasons The reasons why "Shift" does not work on the keyboard do not end there.

Video on the topic

Viruses

But the next scenario is not so common, but it causes a lot of trouble for users. We are talking about the impact of various viruses and Trojans on the operating system. That is, you should not be surprised if an “infection” has settled in your computer, and the “Shift” button on the keyboard does not work. Or if it only performs certain functions that were not originally intended for it.

What should I do? It all depends on the nature of the virus. First of all, it is recommended to save important data to storage media and then scan the operating system antivirus program. After this, you need to “cure” the computer and recheck it. Everything is potential in advance dangerous objects those that do not respond to treatment are removed.

After this, you can reboot the system. And "Shift", if everything is done correctly, will work. Otherwise, you can try to reinstall the OS with pre-formatting hard drive. This is necessary, because this is the only way to completely get rid of certain viruses. This is perhaps the most serious situation that can occur.

Pirate

Shift not working on your keyboard? The following scenario is also not uncommon. And it usually gets fixed without special problems. Shift refused to work? It’s worth considering what operating system is on your computer.

If the user has purchased and installed a license, the suggested reason is automatically crossed out. But often users install pirated Windows on their computers. There is no need to be surprised that one day a problem appeared in which “Shift” on the computer keyboard does not work. This is quite normal for pirates.

There are several ways to proceed. The first is reinstalling the OS. Sometimes it doesn't work the first time. In some cases, it gives no result at all. The second is changing the operating system to a license. If the problem lies precisely in Windows versions, then the keyboard will start working at full capacity.

Settings

But not everything is as scary as it seems. Before you rush out to buy new hardware or reinstall the OS, it is recommended to check your computer settings. Which ones exactly? Sometimes in operating system special settings have been set. Or for some unknown reason they get lost. Because of this, the left "Shift" on the keyboard does not work. And often the right one too.

To check this item, you will have to go to the "Center" special features Windows" - "Keyboard settings". It is recommended to pay attention to "Filtering settings" and "Sticky". Here you can try to turn it on and off additional options associated with the Shift button. The changes are saved, after which you can check the functionality of the keys.

That's all. Now it’s clear why the “Shift” button on the keyboard doesn’t work, and how to deal with this situation. It's actually not that difficult. If you cannot fix the problem yourself, it is recommended to contact service centers for help.

You can often see users complaining that “Shift” on their keyboard does not work. This phenomenon is not so rare. It can be caused by various reasons. Nevertheless, this scenario causes a lot of problems for users. Sometimes it even becomes quite problematic.

So what if "Shift" refused to work? Why does this happen? Is there any cause for concern? Answering all these questions is not as difficult as it seems. The most important thing is not to panic. After all, the problem being studied is not always critical. Moreover, only in rare cases, when the Shift button fails to work, do you have to take drastic action.

Keyboard problem

The first reason is obvious. It occurs quite often, but it manifests itself not only in the fact that “Shift” on the keyboard does not work. The point is that all equipment can wear out. It is likely that the failure of the specified key to work is a consequence of a malfunction of the connected device. What should I do? You can either install a new keyboard and check the functionality of the specified button, or try to repair the old one. As practice shows, the first method of solving the problem is the most effective. What's next?

Blockage

Is the "Shift" button on or "sticky"? More precisely, is it not pressed the first time or does the computer basically not respond to this key? Then you should clean the keyboard. This phenomenon should not be scary. After all, this problem occurs often, especially if a person is used to eating right in front of a computer or laptop.

What's the matter? In the most common blockage. Every keyboard needs to be cleaned from time to time. Otherwise, its buttons begin to refuse to work. Including Shift. Therefore, users quite often advise each other, if any problems arise with the keyboard, to disassemble this component and clean it. Surprisingly, this method very often helps to get rid of problems that have arisen. But the possible reasons why “Shift” does not work on the keyboard do not end there.

Viruses

But the next scenario is not so common, but it causes a lot of trouble for users. We are talking about the impact of various viruses and Trojans on the operating system. That is, you should not be surprised if an “infection” has settled in your computer, and the “Shift” button on the keyboard does not work. Or if it only performs certain functions that were not originally intended for it.

What should I do? It all depends on the nature of the virus. First of all, it is recommended to save important data to the media, and then scan the operating system with an antivirus program. After this, you need to “cure” the computer and recheck it. Previously, all those that did not respond to treatment are removed.

After this, you can reboot the system. And "Shift", if everything is done correctly, will work. Otherwise, you can try to reinstall the OS with a preliminary hard formatting disk. This is necessary, because this is the only way to completely get rid of certain viruses. This is perhaps the most serious situation that can occur.

Pirate

Shift not working on your keyboard? The following scenario is also not uncommon. And it usually gets fixed without any problems. Shift refused to work? It’s worth considering what operating system is on your computer.

If the user has purchased and installed a license, the suggested reason is automatically crossed out. But often users install pirated Windows on their computers. There is no need to be surprised that one fine moment a problem appeared in which “Shift” does not work. This is quite normal for pirates.

There are several ways to proceed. The first is reinstalling the OS. Sometimes it doesn't work the first time. In some cases, it gives no result at all. The second is changing the operating system to a license. If the problem lies specifically in the version of Windows, then the keyboard will begin to work at full capacity.

Settings

But not everything is as scary as it seems. Before you rush out to buy new hardware or reinstall the OS, it is recommended to check your computer settings. Which ones exactly? Sometimes the operating system has special settings. Or for some unknown reason they get lost. Because of this, the left "Shift" on the keyboard does not work. And often the right one too.

To check this item, you will have to go to the "Ease of Access Center". It is recommended to pay attention to "Filtering Settings" and "Sticky Settings". Here you can try to turn on/off additional options associated with the "Shift" button. The changes are saved, after which you can check the functionality of the keys .

That's all. Now it’s clear why the “Shift” button on the keyboard doesn’t work, and how to deal with this situation. It's actually not that difficult. If you cannot fix the problem yourself, it is recommended to contact service centers for help.

Non-working keys on a laptop keyboard is a phenomenon that occurs quite often and leads to a certain discomfort. In such cases, you may not be able to use some features, such as entering punctuation marks or capital letters. In this article we will provide ways to solve the problem with the shift not working.

There are several reasons why the SHIFT key fails. The main ones are reassigning keys, enabling limited mode or sticking. Below we will examine each of them in detail. possible options and provide recommendations for troubleshooting.

Method 1: Virus check

The first thing you need to do when this problem occurs is to check your laptop for viruses. Some malware are able to reassign keys by making changes to system settings. Pests can be identified and eliminated using special scanners - free programs from leading antivirus developers.

After the viruses have been found and removed, you may have to work with the system registry, deleting the “extra” key. We will talk about this in the third paragraph.

Method 2: Hotkeys

Many laptops have a keyboard mode in which some keys are locked or reassigned. It is turned on using a specific key combination. Below are several options for different models.

• CTRL+Fn+ALT, then press the combination SHIFT+Space.
• Simultaneously pressing both shift keys.
• Fn+SHIFT.
• Fn+INS (INSERT).
• NumLock or Fn+NumLock.

There are situations when, for some reason, the keys that disable the mode are inactive. In this case, the following manipulation may help:

Method 3: Editing the Registry

We have already written above about viruses that can reassign keys. You or another user could do this using special software, which was successfully forgotten. Another special case– keyboard malfunction after an online game session. We will not search for the program or find out after what events the changes occurred. All changes are written to the parameter value in system registry. To solve the problem given key needs to be removed.

Before editing settings, create a system restore point

Read more: How to create a restore point in.

Method 4: Disable Sticky Input and Input Filtering

The first function temporarily enables the ability to press separate keys such as SHIFT, CTRL and ALT. The second helps to exclude double taps. If they are activated, then shift may not work the way we are used to. To disable, do the following:

1. Running the line "Run" (Win+R) and enter

   

2. IN "Control Panels" switch to small icons mode and go to "Ease of Access Center".

   

3. Click on the link “Make the keyboard easier to use”.

   

4. Let's move on to the sticky settings.

   

5. Uncheck all the checkboxes and click "Apply".

   

6. We return to the previous section and select input filtering settings.

   

7. Here we also remove the checkboxes shown in the screenshot.

   

If it was not possible to disable sticking in this way, you can do this in the system registry.

Method 5: System Restore

The essence of this method is to rollback system files and parameters to the state they were in before the problem occurred. IN in this case it is necessary to determine the date as accurately as possible and select the appropriate point.

1. Go to the section "System Configuration" from the menu "Run" using the command

   

2. Switch to the tab with a list of services and disable the display of Microsoft products by checking the appropriate box.

   

3. Press the button "Disable everything", then "Apply" and reboot the laptop. Checking the operation of the keys.

   

4. Next, we need to identify the “bully.” This needs to be done if the shift starts working normally. We include half of the services in "System Configurations" and reboot again.

   

5. If SHIFT is still working, then uncheck this half of the services and put it opposite the other. Reboot.
6. If the key stops functioning, then we continue to work with this half - we also split it into two parts and reboot. We carry out these actions until there is only one service left, which will be the cause of the problem. It will need to be disabled in the appropriate snap-in.

In a situation where, after disabling all services, the shift does not work, you need to turn everything back on and pay attention to other methods.

Method 7: Editing startup

The startup list can be edited in the same place – in "System Configurations". The principle here is no different from a clean boot: we turn off all elements, reboot, and then continue working until we get the desired result.

Method 8: Reinstall the system

If all the methods above do not work, you will have to take extreme measures and reinstall Windows.

Conclusion

You can temporarily solve the problem by using the on-screen keyboard, connecting a desktop keyboard to the laptop, or reassigning the keys - assigning the shift function to another one, for example, Caps Lock . This is done using special programs, such as MapKeyboard, KeyTweak and others.