Which side to glue the protective glass on the phone. How to glue protective glass to a smartphone screen? Which is better – glass or film?

When replacing the protective glass on a smartphone, few people do not worry about following the rules and perform re-gluing with improvised tools. As a result: there are scratches on the phone, the coating does not apply evenly, becomes covered in bubbles, or simply does not adhere tightly

When replacing the protective glass on a smartphone, few people do not worry about following the rules and perform re-gluing with improvised tools.

As a result: there are scratches on the phone, the coating does not apply evenly, becomes covered with bubbles, or simply does not adhere tightly.

Instructions: how to install protective glass on your phone

We have prepared a short instruction manual for those who want to install the glass themselves.

The article contains basic information, but to complete the picture we recommend watching the video from detailed description installation stages.

Removing old glass: what is important to remember

You must understand that the glass does not stick to the screen due to a special adhesive coating. The adhesion of the film to the smooth surface of the touchscreen occurs due to statics. An attempt to remove it by prying it with a fingernail or (much worse) with a knife will result in damage to the screen and body of the phone.

Even using a special suction cup can lead to unpleasant consequences. Remember, perform all actions smoothly. By pressing hard on the Velcro, you risk damaging the cables or tearing off the screen module. A vacuum is formed between the glass and the film, which will resist the adhesion of the coatings. But even if the suction cup adheres well to the film, there is a chance of damage to the sensor when removing the protective glass. Therefore, act consistently and carefully.

What to prepare for installing protective glass:

mediator (or thin plastic card) - it’s better to take 2 pieces;

silicone suction cup (if you already have reinstallation experience, you can do without Velcro);

napkin or piece of lint-free cloth;

glass cleaner containing alcohol (pure alcohol or perfume will also work);

medical gloves (silicone or rubber).

Once armed with these tools, the job will take no more than two minutes.

Brief description of the process

Before you begin, make sure your hands are free of dust or lint. It is impossible to see the smallest particles on your fingers, so it is better to play it safe and wear medical gloves. They are thin and fit snugly on the hand, so they will not interfere with your work.

Next, install the suction cup on the area of the phone with damaged glass, where there are fewer fragments and cracks. Carefully apply the Velcro to the corner of the screen, and then press down slightly and glue it to the glass. Take the pick and pull the suction cup towards you, only gradually increase the force, otherwise the glass will come off along with the screen.

As soon as you feel the glass peeling off, deepen the pick.

When the glass around the perimeter peels off ~80%, feel free to pull the suction cup and tear off the old screen.

Gluing new glass

Before applying new coating, remove dust and fingerprints. A lint-free cloth is suitable for this: first moisten the screen with glass cleaning compound and degrease the surface using a prepared cloth.

Take safety glass by the edges (put on gloves first).

Carefully remove the adhesive protective surface on the film (keep the glass near the phone, otherwise airborne dust will stick while you transfer the film).

Place the glass as close to the screen as possible (align it relative to the center, check that all holes for buttons, connectors and the camera pass through the film).

Slowly lower the protective covering onto the screen, pressing and simultaneously smoothing from the center to the corners. Use a dry, lint-free cloth or thin plastic card for this.

Remove the film applied for protection during transportation.

It is not always possible to glue glass to a phone without getting dust and lint. If you see that debris has gotten under the film, peel off the glass exactly to the place where there is dirt.

You can also use a compressor, a technical vacuum cleaner or a can of compressed air to blow away dust particles.

If you don't have anything like this at hand, use tweezers.

As soon as you remove the dirt, glue the glass back.

P.S. And remember, just by changing your consciousness, we are changing the world together! © econe

Protecting your favorite gadget is one of the most important and difficult tasks. It is difficult to choose protection due to the abundance of offers that have different characteristics and degrees of protection. Among the options for increasing the safety of phones, a product such as protective glass stands out, which eliminates most of the negative consequences of impacts, scratches or friction. Moreover, you can stick protective glass on your phone yourself, without having the skills or special tools.

We will determine the positive factors for choosing glass for a phone in the form of a comparison with the same film. IN in this case The following positive aspects will be highlighted:

Impact resistance. Even if you let the gadget face down, with a high degree of probability, the touchscreen will remain intact, and only the protective glass on the smartphone will be damaged if it is glued correctly. Manufacturers claim that some models can even withstand hammer blows. However, such experiments are not recommended.
Scratch resistant. Carrying a smartphone with keys, if the film provides protection, means getting damaged, chipped and scratched. If you use high-quality protective glass on your gadget, such a problem is eliminated with a 99% probability. However, the same keys can leave scratches on the device body or damage other parts of it.
Duration of protection. If you stick tempered glass at home and follow the recommendations, you can create effective protection for many years. Such screens do not peel off on their own, and also maintain transparency, color rendition and tactile sensitivity of the sensor.
Easy to install. An adhesive composition is applied to one side of the protective screen, which ensures a tight fit and turns the structure into a monolith. Moreover, sticking protective glass onto your phone will not leave streaks, traces of glue or other negative factors that would reduce the visual display of information or the quality of transmitted colors. This is achieved due to the unique composition of the adhesive on the glass surface.

Even with reliable protection You need to keep an eye on your smartphone. How you handle and carefully store your device determines its durability and functionality. Remember that a phone screen protector is additional protection, and not a panacea for any surprises and dangers.

Even this reliable method of securing smartphones has several drawbacks. Of course, the disadvantages will not be as significant in comparison with the advantages, but for some users they will be important:

Price. In comparison with the same film, the price for glass for a phone screen will be an order of magnitude higher. If you decide to entrust the sticker to professionals, be prepared for another expense item.
Increase in size. Even if only slightly, your smartphone will become more massive. Yes, the thickness of the protective glass does not even reach a millimeter, but it is even the most thin phone will make it a little thicker.
Accuracy and difficulties with fastening. For some users, properly gluing the protective glass is a significant problem. Even one wrong move will ruin expensive protection and not ensure the safety of your smartphone.

Thus, whether it is worth gluing protective glass to the screen is up to the owner to decide, taking into account the features and operating conditions. The main thing that numerous reviews and instructions for the sticker say is that it can be done even at home, and the degree of protection for the phone will be really high.

You can also leave comments yourself at the end of the article, indicating not only examples from your own experience, but also asking questions to which you will receive a comprehensive answer. Remember that just a couple of lines or a repost on social media. networks will help you solve problems not with impersonal information, but with facts real people who have already tried similar products.

How to glue protective glass on a phone: detailed instructions

Before gluing the glass to the phone, you will need to complete a number of preparatory steps. Actions to secure protection are divided into five stages.

Prepare the room

Preparing the room will include getting rid of dust, debris and even moisture. In this case, we are talking about wet cleaning in the room itself and thoroughly wiping the table. And also don’t forget to wash your hands and dry them with a towel. The smallest hair, speck of dust or drop of greasy sweat can lead to a deterioration in the aesthetic qualities of the device.

Prepare your tools

In order to stick a protective glass on a Xiaomi or any other smartphone, you will need two types of napkins, a scraper (can be replaced with a plastic card), tape, scissors and the directly selected protective glass. All these details should be at hand, but not interfere with the sequence of actions.

First, carefully study all the points in the instructions, and only then get to work. There is no provision for a second attempt, and the first time you can install the protection yourself correctly only by meticulously memorizing the instructions.

Degrease the screen surface

The action will require a special alcohol-impregnated wipe, which will not only remove greasy spots, but also completely clean the display from dust and debris. If such napkins were not provided with the protection, use regular, damp, alcohol-impregnated ones. It is not necessary to buy them in a specialized store, spending extra funds. Just buy napkins from household supplies stores too. After this, use microfiber cloths to complete the cleaning.

Stick the glass

Try to glue the protective glass onto the iPhone as accurately as possible. Remove protective film and hold the glass directly above the device. All edges must match and the holes must line up exactly with the button and speaker. In order to stick the glass on the iPhone, you don’t need to level it or press hard – a light press on the center of the screen will be enough. Immediately check that the sticker has passed without bubbles or lint remaining between the glass and the display.

Remove missed dust particles

They should be removed by carefully lifting the edge of the glass with a scraper or plastic card. Moreover, sticking it correctly without bubbles and lint means making it completely invisible. If you didn’t manage to carry out this procedure yourself the first time, lift the glass from the edge and remove the specks of dust or hair with tape by sharply pulling it.

Do not use colored tape or paper versions of tape with glue - they may leave streaks and impair the display of information. The pasted film or glass, if all actions are strictly followed, should not impair visibility. If you managed to stick the protective glass on your Xiaomi, but bubbles formed, remove them by squeezing them out with a microfiber cloth. Light pressure and moving the bubbles to the nearest edge of the display will quickly achieve the desired result.

Features of stickers for some phone models

The main feature of each individual product will be its size and the presence of holes for function keys. As an example, it would be relevant to study the features that protective glasses for iPhones have, for example, a product such as Zool iPhone 5 0.1mm 9H.

Such pieces of glass have such features as exact matching to the size of the smartphone, the presence of a special coating for comfortable control of the device, and increased protective properties combined with an ultra-thin design. However, as with other products, it is unlikely to be possible to remove the protective glass and reinstall it a second time.

Remember that you are putting a screen protector on your iPhone for security, not aesthetics or functionality. Carefully match all edges and holes before applying the screen to the device.

Having decided on this type of security, you should know that all glass is tempered, but is endowed with different properties. There are two types protective screens– with glossy and matte finish.

In the first case, protection against scratches will be minimal, since the screen itself can easily receive minor damage. This type of glass is glued to effectively resist falls and impacts, preventing damage to the touchscreen.

Matte protective glass on an iPhone or other types of gadgets will have a higher degree of protection, including anti-reflective coating. The negative side of such a purchase will be the high price, especially if you are purchasing a product from a well-known brand.

When choosing protection, focus on the equipment, the properties you need and reviews of other consumers. You can leave your own comment below, which will help other site users make the right choice based on personal experience.

In conclusion

Protective glass is an opportunity to increase the security and safety of your smartphone. You install protection that cannot be quickly changed, like the same case, or you can constantly drop your gadget without worrying about shocks and possible scratches.

Durable and reliable glass must be glued correctly and as accurately as possible. Subsequently, gluing the protective glass onto the phone if it comes off is unrealistic. The adhesive used in such products cannot be replaced with superglue; you will only damage the display. If the protective glass on your phone comes off, it is better to remove it to avoid damage or debris getting between the screen and display, which could damage the touchscreen.

We will be grateful if you add yours to our article. own experience with specific phone models. Protect your smartphone, and it will respond to you with constant functionality and help in any situation.

For those who find it easier to visually study the information in a video, look at an example of a protective glass sticker, using small strips of tape for accuracy. This method will also be relevant, but is not suitable for all phone models.

How to stick a protective glass on an iPhone yourselfMany iPhone owners We try to treat the device as carefully as possible. For this purpose, various covers, bumpers and protective glasses are purchased.

How to do it

Before gluing the protective glass, remove the iPhone case. If the iPhone display is already covered with old film or glass, feel free to remove it. Wash your hands thoroughly to avoid getting dirt on the screen.

It is best to glue in a well-lit place so that you can see every speck that gets on the device screen. Well, choose the cleanest possible surface for gluing the glass.

Let's get started

Step 1. Clean the iPhone display.

To do this, we use any microfiber cloth so as not to leave anything unnecessary on the screen.

You can also use an alcohol wipe and then wipe the display with a soft microfiber cloth.

Step 2. Additionally, clean the smartphone screen using the supplied tape or any other sticker.

Simply touch the display with tape and lift it back up. The adhesive surface will collect any remaining dust.

Step 3. Now you need to remove the protective film from the adhesive side of the glass and apply it to the screen.

Important: hold the glass by the edges to avoid leaving unnecessary marks on it.

Step 4. Carefully place the glass on the iPhone screen.

If the glass is good, it will fit on the smartphone screen on its own. But to be extra sure, you can smooth it out yourself.

We run our finger through the center of the smartphone and begin to smooth it until all the bubbles are removed. If there are any small bubbles left, take a plastic card and, using light pressure, swipe it over the areas where the bubbles formed.

In this tutorial we used Mocoll glass. And it’s not just like that When you look with sadness at the iPhone, the display of which is covered with a merciless mesh, it’s too late to think about protection. The manufacturer of protective accessories Mocoll took care of the consumer in advance.

All brand products are designed in such a way that the buyer spends a minimum of time gluing the protective glass.

Considering that Chinese brand Mocoll (our review) has been producing protective glass for several years; the company's engineers have thousands of hours spent in research laboratories.

Glass is produced using high-tech equipment and receives a number of important properties during the processing process. Glass from Mocoll:

They are only 0.33 millimeters thick. Glass is homogeneous and has equal thickness at any point. Among glass manufacturers, Mocoll has one of the lowest percentage of tolerances in production.

Mocoll glass easily withstands the impact of sharp objects and does not crumble into fragments upon impact.

Hardness at 9H on the Mohs scale. Only diamond is higher.

The glass has an oleophobic coating, so after gluing it you will not feel any tactile changes from interacting with the iPhone screen.

Mocoll supplies its products with a rich package. The kit contains everything you need to glue glass without additional purchases or searching for a piece of fabric or plastic card to eliminate bubbles.

Mocoll has several options at once protective glasses. 2.5D, 3D and advanced development - 3D glass with elastic edges to match the color of the device’s body.

As you can see above, installing Mocoll safety glass is very easy. Due to the presence of a special silicone layer, you don’t have to worry about the appearance of hated bubbles during gluing.

For every taste, color and budget

Mocoll literally has glass of all shapes and sizes. The range includes glass for tablets and smartphones (and not only Apple), there is also protection for MacBooks.

Among the most interesting options special glass with protection against peeking.

It works in such a way that after gluing, you can only see what is happening on the iPhone display from a strictly certain angle. That is, you, as the owner, can calmly text or watch a movie, and the bus passenger sitting next to you, no matter how much you want, will not see anything.

The glass is designed in such a way that it refracts the light emanating from the screen, making the picture inaccessible to others.

Mocoll glasses are very popular. Many people use accessories from this manufacturer. service centers and workshops. They are really very durable..wrapper ( padding: 10px;

#hid-button,.hid ( display: none; )

#hid-button:checked ~.hid ( display: block; )

#hid-button:checked ~ label ( background: #e4e4e1; )

#hid-button:checked ~ label:before ( content: "Hide"; )

label ( display: inline-block;

padding: 5px 10px;

Hello!
Indeed, as Felicity noted, “few people succeed the first time.” But what if this “time” is the only one? And is there a high risk of getting poorly glued glass with lakes of air under it? But you can get excellent results the first time. But this requires an understanding of the essence of the process and appropriate equipment of the workplace.
First, I will describe the essence of the process. Since all objects are plastic, when manipulating them, they are easily electrified. And while the old film peels off, the screen is rubbed with a napkin, the film is removed from the new glass, the surface of the screen and the new glass become electrified and manage to attract microparticles from the air. Microparticles fall from clothes, scalp hair... You never know where! We cannot see them with the ordinary eye. But by gluing glass or film to the screen, they begin to be clearly visible as air bubbles. And it will not be possible to remove such a bubble, because the microparticle has already “glued” into the adhesive layer of glass or film. The air would be squeezed out during ironing, but the particle would not. But it creates some kind of cavity for air.
Therefore, the main requirement is to deelectrify the working volume, remove electrical charges from yourself, from clothes, from glass, from the screen.
For this;
1. Prepare a spray bottle. A very convenient bottle (25 - 50 ml) with a pressure sprayer made of ethyl alcohol (buy at a pharmacy). Fill an empty bottle with preferably distilled water with half a drop of Ferry. Read and consider Felicity's addition. Practice spraying thin layers on any item.
2. Choose the table at which you will work. There should be no passing air flows or drafts capable of carrying dust.
3. Wipe the table surface with a damp cloth with a small amount of Ferry. This will remove static from the table surface and remove and bind any remaining dust.
4. Boil a kettle with a spout in advance and place it on the work table on an electric stove, 30 - 40 centimeters from the work area. So that it gives a stream of steam passing 40 - 50 centimeters above the table. This steam will remove static from objects in the work area. But don't overdo it. There should be no condensation in the form of rain or showers.
5. Prepare all the components on the table.
6. Wash your hands and preferably your face with soap a couple of times. When washing your hands, you pass yourself through a stream of water (and water conducts electric current), “ground” through the water supply system. And you will wash away microparticles of skin and fat from your face. This will not only give you clean hands (which is very important), but also refresh yourself before work.
7. Perform all the operations described by the author of the article and use the add-on from Felicity. In 12–17 minutes, if you carefully read the article and recommendations, you will get beautifully glued glass without air inclusions.
Tested many times by svoimirukami!

Every owner of a brand new smartphone wants to protect the gadget from scratches and chips. Accessories and protective elements have been created specifically for this purpose, allowing you to extend the service life of the device, and for a long time keep original appearance. Films were especially popular some time ago, but today we are concerned with another question - how to properly stick protective glass on a phone. It is now more often used to ensure screen security.

For some users, the difference between traditional film and glass is still unclear. The latter is also flexible and quite elastic. But still, this material is stronger, it is hardened with high quality, it is made super durable, capable of protecting the display from many damages. This element is worth using for people who regularly drop their smartphone, or for those who are afraid of damaging the monitor. The special coating strengthens it and helps it remain intact even if it falls from a great height. So in the event of a serious impact, the fragments under protection will not fly apart.

Such an accessory costs more than the same films, because the characteristics are more significant. It should be taken into account that the protective glass cannot be “fitted” to a smartphone and pasted, so it is necessary to specific model select a finished product, for example, for Xiaomi Redmi 4, it is important to find an accessory made specifically for it. In the salon, you will have to pay extra for installing this element, so the question of how to stick protective glass on your phone at home is very relevant. Naturally, you can do this yourself correctly.

The coating usually has a thickness of 0.18 to 0.33 millimeters. In some cases, it adds additional weight to the gadget and makes it more bulky. The accessory has about five layers:

silicone part – is responsible for a stronger fixation of the accessory on the gadget;
containment layer - retains fragments so that they do not crumble in the event of a serious impact;
protection – ensures the strength of the material;
anti-glare layer - thanks to it, the device is comfortable to use even in bright sunshine;
oleophobic layer - allows you not to leave fingerprints on your phone monitor.

The coating does not affect the sensitivity of the sensor element and does not distort anything. The numerous benefits of protection have helped her become so popular, and she also does her job well.

How to glue protective glass on your phone and all stages of preparation

You must follow the instructions. The procedure does not take much effort and does not require additional costs, but it is better to prepare the necessary equipment in advance. To apply the coating yourself and correctly you will need:

alcohol wipe (available at the pharmacy);
not a hard dry cloth;
a special liquid used to wipe displays and TVs, it is sold in stores, but you can also make it from alcohol, water and dishwashing detergent;
adhesive tape or a special dust collector;
directly to the protective glass.

You need to prepare any card made of plastic, if the kit did not include a professional spatula, in order to stick it correctly.

It is important that the working area is not dusty. It is better to do this in the bathroom or kitchen. You should wipe the table clean with napkins on which you will glue. Wash your hands several times.

Instructions: how to properly and accurately stick protective glass on your phone

Tools, materials collected, workspace, hands clean? Then let's start:

Prepare your phone screen. Remove the old coating by slowly catching the edge. Any film will peel off easily.
Clean the surface with an alcohol wipe or rag and moisten it with display cleaner. Walk thoroughly over the entire area to remove dirt. The screen is rubbed to shine.
If there is still dust, tape will come in handy.
Take the protection out of the packaging, removing the films if necessary. It is important that all elements of the screen coincide with the glass accessory (buttons, speakers). The coating must align correctly and evenly with the gadget. Be sure to hold the edges of the protective glass to avoid leaving fingerprints. You can wear medical gloves.
You need to stick the protection like this: move your finger in the center from top to bottom. After using a special device or card, the remaining air is eliminated; they must be moved to the edges from the center. It's better to stick without bubbles, but if there are any, don't worry. Usually the air will disappear after a few days. So don't press too hard on the screen.

If you followed the instructions, you will get a smooth, crisp finish with no marks. The display has become cloudy - it has not been cleaned well. In this case, you will have to perform the procedure correctly again.

Is it possible to re-glue the protection?

When the installation procedure was carried out incorrectly or you simply want to remove it and move it to another phone, this question arises. If the surface of the accessory is not worn out, then you can stick it a second time.

First, treat the adhesive layer of silicone with formic alcohol. It is worth removing the glass and cleaning the side with the adhesive base with a damp cloth. Wait until all the excess drains and dries, after which you can re-stick the coating on the phone, aligning it with the holes. The entire sequence of actions was described earlier. Note that it is easier to install protective glass correctly than the usual film. Its density is higher, so folds and waves will not appear. Although it is more difficult to remove the glass element from the display, this requires taking a card, sliding it under the covering and swiping it across it.

Now you know how to properly apply a new protective glass to your phone. Installation instructions suitable for everyone mobile devices. The only thing you should remember is that each model of the device has its own protection, suitable in size and shape. If you have any questions, ask in the comments. Be sure to subscribe to blog updates so as not to miss the most interesting things.