Correct replacement of light bulbs. How to replace a burnt out halogen light bulb

Halogen bulbs, unlike incandescent bulbs, shine brighter and consume less electricity. But at the same time, they also burn out quite often, and self-replacement they are connected with some nuances that you will learn by reading this article in full.

Replacing a halogen lamp with a two-pin base (G4, GU5.3)

Replacement procedure

Open Bulb Light Bulbs usually hidden under various lampshades (a common option is built-in backlights in furniture cabinets).

To remove the decorative shade, try slightly turning the decorative ring that holds it in a counterclockwise direction. If you are unable to remove the lampshade, you will have to completely pull out the lamp.

To remove the lamp, carefully slide a flat tool (screwdriver, ruler, spatula) between the edge of the decorative ring of the lamp and the ceiling, then slightly pull the lamp out of the hole in the ceiling until the spacer springs appear.

Press both springs against the light with your fingers and continue to pull the light out little by little. By pressing the springs, you will not allow them to suddenly open when the lamp is finally removed, and thus protect both the hole in the ceiling and your hands from damage.

If the light bulb slips in your hands and does not want to rotate, then try turning it by wearing rubber gloves or using a suction cup.

3. Buy a new light bulb to replace it. Preliminarily determine the characteristics of the burnt out light bulb. Be especially careful with this point, because halogen light bulbs are designed for both 220 volts and low voltage (12 volts).

An indication of the type and power of the light bulb can be found on the lamp, or read on the light bulb itself.

4. Install the new working light bulb in place.

When installing a new halogen light bulb in its rightful place, you must take into account that it is strictly not recommended to touch its bulb with your hands. The fact is that during operation, the bulb of a halogen lamp gets very hot (it is even made of heat-resistant quartz glass). And if there are greasy fingerprints on it, then in this place the glass will heat up even more.

A burnt grease stain forms carbon deposits on the flask, which makes it even hotter. The glass in this can melt and even swell. All this leads to destruction or premature burnout of the halogen lamp.

Therefore, hold the lamp without touching it with your fingers. Use the packaging in which the lamp was sold or hold the lamp through a dry, clean cloth (polyethylene). If you did take the lamp with your fingers, then it must be degreased with a lint-free cloth moistened with alcohol.

This does not apply to lamps whose bulbs are “hidden” inside the reflector and covered with protective glass. You can safely take such lamps with your hands.

5. After installing the light bulb, try turning it on and then, if everything works, reinstall the light bulb in the reverse order.

Replacing a halogen light bulb with an r7s base

This is also a fairly common type of lamp, most often used in floor lamps, as well as floodlights for outdoor lighting. Lamps with r7s base are available in various lengths and wattages.

Replacement procedure

2. Grasp the bulb with your hand and lightly press the lamp with one end of the base into the socket, while pulling the other (released) end of the base towards you. Thus, one end of the base, and behind it the entire lamp, should come out of the socket.

3. Buy a lamp of the required size, power and voltage from the store. Remember that a halogen lamp should not be touched with your hands, so install the new light bulb in place using a clean cloth, glove or piece of non-slip polyethylene.

Typically, this type of light bulb is sold packaged in polyethylene, which can be used to hold the lamp during installation. Just remember to remove it after installation.

4. Insert one (either) end of the light bulb into the socket and, pressing lightly on it, insert the other end of the light bulb into the opposite part of the socket so that the light bulb is securely fixed between the clamps of the socket.

If you see that the light bulb is not installed tightly and is dangling between the clamping contacts of the socket, then you need to remove the light bulb and bend the clamps or socket mount so that the light bulb “fits tightly” in the socket. If the clamping contacts of the cartridge are severely burnt and cannot be adjusted, it will be necessary to replace the cartridge.

5. Turn on the lamp. If everything works fine, install the protective glass or lampshade in its rightful place.

If you wish, you can find out how to replace lamps by reading about it in the corresponding article.

For greater clarity, you can watch this short video on how to replace burnt out halogen light bulbs. The video will open in a separate window.

Press the ↓↓↓ button and share with your friends if you find this article useful!

The source of light plays a very important role in our lives. important role, And modern man feels terrible discomfort with his absence. The problem of light bulb failure is the simplest and most common. electrical fault. To quickly restore the lack of light, you need to know how to change light bulbs.

Installation locations and the light bulbs themselves are currently so diverse in design, power consumption and required voltage, material, operating principle. All these characteristics need to be known when replacing the lamp.

It is advisable to change light bulbs during the day if there is a sufficient source natural light. To replace, you will need pliers with insulated handles, a screwdriver, a flashlight (for working in dark rooms - pantry, bathroom, basement), a replacement light bulb, and rubber gloves.

Before changing the light bulb, it is necessary to de-energize the power supply section (turn off the circuit breaker in the electrical panel or unscrew the plugs). Replacing a light bulb involves removing some parts of the lamp structure (shades, protective frames).

Incandescent lamp

The burnt-out light bulb is unscrewed counterclockwise with one hand, and the socket is fixed with the other hand. How to change light bulbs, if in many cases the bulb of an incandescent lamp can become damaged (crack, “explode”) and become detached from the socket. In this case, holding the cartridge with your hands, remove the remains of the flask using a rag. Eyes must be protected with goggles. Unscrew the base of the old light bulb with pliers. This will protect your fingers from damage and will add force to the base if it is screwed in tightly or “stuck.” The replacement bulb is screwed in clockwise until it stops. There is no need to be very zealous, as you can damage the flask.

Energy saving lamps

Design energy saving lamp has a standard Edison base, and instead of an incandescent lamp bulb, it has a compact fluorescent tube. Replacing it is a little easier than incandescent lamps, since in the base area it has a choke location block, which helps to change a burnt-out lamp with ease of grip.

Replacing lamps in built-in luminaires

More knowledge on how to change light bulbs is required when replacing them in built-in (spot) lamps. Here you need to take into account the type of base. It can be threaded with different diameters. Also popular is pin with varying amounts pins. The lamp can be either LED, halogen or fluorescent. Required electrical power for them it is also different, 12V or 220V. You need to select an identical light bulb either from the packaging of the burnt one (where the marking is indicated) or from a sample.

Built-in lamps are mounted in the ceiling using double-spring struts. The lamp must be taken by the edges and slowly pulled down. Sometimes you don’t have to pull it out completely; a certain length is enough to unscrew a lamp with a screw base. If the lamp is completely removed, then after screwing in a new light bulb, you need to compress the springs to the base and insert it into the mounting hole, slowly insert the lamp into the ceiling.

The pin bulb is secured in the luminaire with a locking ring. It must be squeezed with your fingers and pulled out. The light bulb will hang on the wires. Disconnect the lamp from the terminal. Connect the new one and recess it into the lampshade, securing it with a retaining ring.

The fluorescent lamp is very common due to its efficiency. The lifespan of such lamps is quite long, but still not infinite. You can learn how to easily and quickly replace a fluorescent fluorescent lamp, and what nuances need to be taken into account when replacing them, from this article.

Such lamps are most often used in ceiling lamps, to illuminate the work surface of kitchens, in bathrooms, as lighting in mirrors, etc. Lamps are available in various sizes and wattages.

In most cases, the lack of glow is caused by the lamp itself, although sometimes the culprits are the inductor (ballast) or (if present) the starter. A burnt-out lamp can most often be identified by a dark-colored ring on the bulb near one end of the lamp.

Replacement procedure

2. Remove the lamp shade or grille to provide access to the lamp. Transparent shades ceiling lamps can be attached to the lamp body with screws or latches. Inspect the lamp and unscrew the screws, or release the latches and remove the lampshade or reflective grille.

4. Buy a lamp of a size and power that matches the parameters of your lamp. If you cannot accurately determine the characteristics of a burnt-out lamp, take it with you to the store so that sales staff can select the correct replacement lamp.

5. Install a new lamp into the fixture. To do this, carefully insert both ends into the socket until it stops and carefully rotate the lamp around its axis 90 degrees (the direction of rotation is still not important). In some cases, you will feel a slight click as the lamp locks into position.

6. Turn on the lamp and check its functionality. If everything works fine, reinstall the lampshade or decorative grille. If the lamp does not light up, then turn off the lamp switch and try to carefully move or slightly rotate the lamp in the socket, or remove it and install it again.

If, after all attempts, the installed working lamp refuses to light, most likely the problem lies in a burnt-out inductor (replacing it is often comparable in cost to the cost of the lamp) or starter. All these parts are located inside the lamp body, and replacing them will require additional skills, especially replacing the choke.

If you do not have independent experience in performing such work, entrust it to a specialist or buy a new lamp if the cost of repair is equal to the cost of the lamp itself.

Separately, it is worth talking about replacing a burnt-out fluorescent lamp in a desktop office or home lamp. Such luminaires mainly use fluorescent lamps with sockets such as G23, GX23, 2G11, etc.

There may be some differences in the size and shape of the bases, but the principle of connecting the lamp to the lamp socket is the same for all. Thus, these instructions can be applied to all such lamps.

Replacement procedure

2. Place the lamp on the table and turn the shade up so that it is convenient for you to remove the lamp. Most often, the free end of the lamp is attached to the lampshade using a special plastic clamp.

In order to remove the light bulb from the socket, first carefully pull it by the edge of the bulb in the direction from the lampshade, as if bending it, thereby removing it from the retaining bracket. If this bracket is already broken off (a fairly common occurrence), then skip this point.

Take the lamp with your hand (grab it with your fingers) by the bulb and simply pull it, shaking it slightly, in the direction from the socket hidden in the lamp body. The lamp should, with slight resistance, jump out of the socket.

3. Buy a new lamp. If you cannot unambiguously determine the size of the lamp and the type of base, then take the burnt-out fluorescent lamp with you to the store or market when you go to look for a replacement. This way the seller can easily select the new lamp you need.

4. Install the lamp in the lamp. Once you have mastered the procedure for removing the lamp, it will not be difficult for you to do reverse actions. Insert the new light bulb with the base into the socket and press the end of the bulb, pushing the light bulb into the socket. It should go into the cartridge all the way with a barely noticeable click.

Be careful when inserting the bulb back into the plastic retainer. Over time, the plastic of the retainer becomes extremely brittle and can easily break. At the same time, do not be too upset if this happens - this will not affect the operation of the lamp in any way.

IMPORTANT: A fluorescent lamp contains 3 to 5 mg of mercury, a very toxic metal. You should absolutely not throw away used lamps with household or construction waste. As a result of damage to the bulb of such a lamp, mercury will be released into the environment. Please ensure safe disposal of the fluorescent lamp.

By clicking on the image below, you can watch a short video on how to replace a fluorescent fluorescent lamp. The video will open in a separate window.

Press the ↓↓↓ button and share with your friends if you find this article useful!

How to change a light bulb if the old one is burned out? It seems obvious to everyone and simple action, but if you replace the light bulb incorrectly, you can get bad consequences.

Everything is very simple at first glance, however, in order for the light bulb to last as long as possible, you need to follow several rules.

Which light bulbs require proper replacement:

• incandescent light bulb;
• halogen;
• replacing the LED light bulb;
• luminescent.

Replacing an incandescent light bulb

Before you begin the process of replacing the light bulb, make sure that there is no leakage at all. To do this, move the machine’s toggle switch to the “off” state in the distribution panel.

After you complete this action, be sure to check whether the apartment is actually de-energized, since sometimes distribution panels can be difficult to understand, and there are no marks there.

Tip: Before turning off the power, check to see if any appliances are turned on, as they may be damaged or even burnt out.

The power of lamps is measured in watts, and usually a lamp with a power of 100 watts is suitable for simple use.

How to change a light bulb correctly:

• to replace a light bulb, unscrew the old lamp counterclockwise;
• screw in the new lamp clockwise, but do not use much force when screwing in, because you can damage both the lamp and the luminaire;
• turn on the toggle switch in the distribution panel;
• turn on the switch of a regular switch.

If you change the lamp in a chandelier, you do not need to stand under it when you turn it on for the first time. Externally, the lamp may be in good working order, but in fact, sometimes there are defective lamps. When turned on for the first time, such devices may explode and injure you with shrapnel.

How to change a halogen or LED light bulb

In suspended ceilings, spot lighting is usually based on the use of halogen or LED lamps. In order to correctly replace such a lamp, while ensuring that it doesn’t hit you, you need to know some nuances.

First you need to unlock the light bulb in the lamp housing. To do this, carefully remove the special round-shaped ring. After the lock is removed, you can unscrew the lamp. Usually this is not difficult.

When replacing the light bulb, hold all parts with your hands, since the retaining ring has the appearance of a spring that can slip out of your hands.

If you previously had yellow lamps, but there was not enough lighting in the room, you can purchase a new lamp of the same color, but white. It will give more light, and the amount of energy will be spent the same as the yellow one.

If you are faced with the issue of adding more to your room, it is worth considering that you will need the same light bulbs as the ones you already have.

The thing is that different lamps have not only different features, but also appearance, therefore it is advisable to use lamps from the same manufacturer in one room if we are talking about spot lighting.

And the most important thing about halogen lamps is that they should not be touched bare hands. All actions should be carried out only with gloves, because this will help protect the lamp from premature damage.

By the way, if you do touch the light bulb, don’t be upset, you can gently wipe it with a cotton swab with a little alcohol on it.

Replacing fluorescent lamps

When using this type of lamp, it is important that it is in order.

Replacing such a light bulb is not at all difficult; it is similar to the process that we described when replacing an incandescent lamp.

However, if such a lamp has burned out for the first time, you need to remember that when purchasing a new one, its power should either correspond to the old lamp, or be based on the following principles...

Firstly, fluorescent lamps give a greater glow with less power, so there is no point in looking for the most powerful one, because 50 W may well be enough for you to illuminate a large room.

Secondly, it is this type of lamp that gives soft light and diffuses it well, so you definitely won’t need several lamps in one room.

However, it is worth understanding that if you decide to replace, for example, a conventional incandescent lamp with a fluorescent lamp, then the latter option will possibly blink and is also very sensitive to high temperatures. At the same time, little will affect the service life of such a lamp, and it often lasts 10-20 times longer than an incandescent lamp, of which, by the way, you may need several for one room. Create in your room and protect your eyesight!

How to change a light bulb in a suspended ceiling?

To change a light bulb in a suspended ceiling, you don’t have to turn to professionals for help. You can do this yourself. Depending on the type of lamp installed, replacement instructions will vary.

Getting a regular incandescent lamp is not difficult, but before replacing other types of lamps, it is better to read the step-by-step instructions.

For what reasons are light bulbs replaced?

Stretch ceiling is a modern design solution that can decorate any interior. When choosing lighting there is a lot of room for imagination - from a chandelier, LED strip to spotlights different sizes and forms.

But sooner or later you have to change the light bulbs. Why is this happening?

• The lamp is out of order. This is the most common reason, so you shouldn’t skimp on buying a lamp. Then the replacement procedure will have to be carried out very rarely.
• Change of interior. This common reason, which requires the dismantling of old lamps. But you don't have to remove all the bulbs. Sometimes the solution may be to buy covers for spotlights, which will give them an updated look. As for the chandelier, here you can remake each lampshade or purchase new ones.
• And another reason why lamp dismantling is inevitable is replacing the entire blade. It is impossible to replace a suspended ceiling with a new one without affecting the lamps.

If for any of these reasons it was decided to replace the lamp with another, then you should familiarize yourself in detail with the rules for dismantling each type of lamp. In this way, serious mistakes will be avoided.

Replacing a halogen lamp

This is one of the most popular lamp options, which is often used in spotlights. He has high power, hence the short service life. To replace it with a new one, you need to follow simple rules.

• First you need to turn off the electricity in the room.
• Before work, you should wear cotton gloves, because the body of the halogen emitter has a high temperature. Do not touch the surface of the light bulb without gloves.
• Only after this the fastenings are removed and unscrewed. old lamp and replaced with a new one.
• The new model is fixed with fastenings.
• It should be taken into account that the body of the halogen lamp must be at a distance from the canvas of at least ten centimeters.

Replacing the LED lamp

Such lamps are convenient and profitable because they do not require a lot of electricity. This means they will last a long time.

But nothing lasts forever, so sooner or later this light bulb will have to be replaced with a new one. How to do this?

• First, you need to make sure that the electricity in the room is turned off.
• If you are replacing a light bulb in the evening, it is better to take a flashlight with you to make it easier to navigate.
• After this, you need to remove the fastenings of the old lamp.
• Then the insulation from the wiring is removed.
• Afterwards it is necessary to disconnect the wires.
• In order not to act “blindly”, it is better to read the instructions for the new lamp.
• Then directly insert the new LED lamp.
• Then you need to connect the necessary wiring and attach the cover with screws.

Even though led lamps require periodic replacement, they are still more economical and are very popular among owners of suspended ceilings.

Replacing a spotlight

Working with this type of lighting device will require a little more skill.

• First you need to disassemble the box, disconnect the wiring and remove the old lamp.
• For a new lamp, you need to open the box and connect wires of the same color.
• Then, using special pliers, you need to crimp and close the wiring with a cap.
• When all the wiring is in the box under the cover, you can install the light bulbs.
• Then you need to fix the lamp in the ceiling spot. Its power should not exceed that indicated on the flask.
• After finishing work, you can turn on the voltage.

To properly remove the spotlight and screw in a new one, you need to take precautions.

• Turn off the electricity before replacing the lamp, otherwise there may be an electric shock.
• The lamp must be held by the springs, otherwise they will damage both your fingers and the ceiling.

By following these simple rules, you will be able to easily unscrew the spotlight.

Which dismantling is considered incorrect?

Some people mistakenly believe that replacing a light fixture requires cutting the fabric around it. But this option not only wrong, but also dangerous. Why?

• Firstly, it will be almost impossible to restore the canvas after such a procedure.
• Secondly, if you touch the wrong wire, you can get a serious electric shock.
• The new lamp must be larger in diameter, because the installation location will increase due to the cut, and the old lamp size will not fit.
• If the product is under warranty, then after such intervention it will no longer be valid.

With such an impact, the entire stretch ceiling may be irreparably damaged and the only way out will be to replace it with a new one. Therefore, if you are unsure of your abilities, it is better not to take risks, but to seek help from professionals.

How to remove a chandelier from a stretch ceiling?

It happens that to replace a lamp it is necessary to remove the chandelier. You can do this yourself, following the recommendations.

• If the chandelier hangs on a hook, then after removing the protective cap you need to reach it with your hand and grab onto this fastener. After removing the chandelier from the hook, you need to work with the wiring, disconnecting them.

• If the chandelier has a cross-shaped strip, then its dismantling will be a little more difficult. First, the lamp must be freed from the shade, lamp and other decorations. Only after this the cap is unscrewed and the fastening system is disconnected (you just need to unscrew the screws). Then, by analogy, work with wires occurs.
• Experts advise not to purchase flat horizontal chandeliers for suspended ceilings, especially with incandescent lamps and halogen lamps. Their heat can cause the fabric to melt.

When replacing a light bulb on a suspended ceiling, it is worth considering some more nuances.

• If the suspended ceiling has mirror elements, then you need to change the lamps carefully to avoid damaging the surface.
• It is better that the lamps are the same, otherwise the light supply will be uneven. In addition, uniformity always looks more aesthetically pleasing. If you cannot find the right lamp, it makes sense to replace everything.
• It is better to work with gloves. This way the lamp will have a long service life.
• Lamps with high power do not fit well with suspended ceilings. It is not recommended to screw in a lamp with a power higher than 35 watts, otherwise there is a risk of damage to the material.
• For preventive purposes, you should not overheat the devices unnecessarily, since any equipment needs a break in operation.
• It is better not to skimp on quality lamps. They will last longer and will have to be replaced less often.

Thus, replacing a light bulb is not as difficult as it seems at first glance. The main thing is to strictly follow the recommendations, and everything will work out.

For information on how to change a light bulb in a suspended ceiling, see below.