• How to remove protection from an SD card. The storage is write-protected: how to remove protection on a memory card in a Samsung phone

    An attempt to save new information on a micro CD will fail if it is write-protected. There may be different reasons for the access denied message to appear. You can remove protection from microSD using several methods - software and physical. Let's look at the most relevant ones.

    Unlocking microSD

    Place the memory card on a flat surface or in the palm of your hand with the label facing up. On the top left side of the card body, find the small lock switch lever - the Lock button. “Locker” serves to protect information from accidental erasure. The lever may be flat and only slightly protruding from the body, white or silver color. There is no such switch directly on microSD. Insert the card into the adapter and locate the Lock switch on the adapter itself. Move it all the way in the opposite direction.

    After moving the Lock lever to the position of canceling the data protection status, reappearance The write error notification window may be caused by moving Lock back to the protected position. This happens due to the weakening of the switch; when you insert a memory card into the card reader, it moves and turns on the memory lock. Secure it with a piece of rubber band, cardboard, or remove it completely.

    Avoid automatic locking You can record to microSD by removing its contact with the Lock button on the adapter body. Find a small notch on the left side of the micro-flash drive, solder it with plastic or seal it with tape. Soldering must be done very carefully. The option with tape is simpler, but it can get stuck when inserting the card into the adapter.

    Changing disk properties

    If the memory card protection does not allow you to copy information to another drive, but you need to save it, then try removing the protection as follows. Connect the micro CD to your computer, find its name in the list of devices and right-click on it. From the menu, select the “Properties” line, then the “Access” tab. In the next window there is “Advanced settings”, open it and check the box “Open general access", confirm the settings - "Ok".

    Formatting a card microSD memory

    Sometimes, to remove protection from a memory card, it is recommended to format it if the “locker” is missing or did not help. Save important information to another disk, because... it will be completely deleted. You can programmatically remove the block from writing to the card when Windows help.

    Insert the microSD memory card into personal computer through a special adapter directly or through a card reader. Modern laptops already have such a connector; it is usually marked with a “card” icon and looks like a narrow slot. The operating system will recognize the drive and its name will appear in the list of devices on your computer.

    Right-click on the CD drive icon and select “Format…” from the expanded menu. Set the file system to the one that your device supports, usually NTFS. Click "Get Started." All information on the disk has now been deleted and the protection status has been removed.

    Changing the file system

    When writing a file larger than 4 GB to a memory card, an error notification window may appear due to file system limitations. If the memory card is formatted with FAT32, the file size is one of its limitations for recording data. You should change the file system to NTFS, as described in paragraph 3.

    Software tools for microSD

    You can reset the write protection on a disk using software without deleting the information. There are various scripts and utilities for this, for example reset.zip. Downloading software from the network, you should be careful - it may contain viruses. It is better to use proven applications to remove protection. Low-level disk formatting utility Hard Disk Low Level Format The Tool erases all data, but will help restore even hopeless flash drives that were not formatted internally using Windows.

    Removing microSD protection via a mobile device

    Modern mobile devices: players, PDAs, phones, cameras have the function microSD formatting. Try to find this option through the settings and format the flash drive directly to this device. Memory protection could be software installed in the device to ensure data confidentiality. You can also remove protection in the settings. All types of electronic devices have their own characteristics, so if you have any difficulties, read the gadget’s instructions or get an explanation from a specialist at the service center.

    Physical damage to the microSD memory card

    One of the failure options when trying to write data to a memory card occurs due to physical damage: the card is slightly bent, one of the contacts on the card (usually the left one) or on the adapter is dirty, and the microSD closes it. If the contacts become dirty, they must be cleaned, for example, with a cotton swab dipped in an alcohol-containing liquid or acetone. A badly bent card cannot be repaired. You can try to straighten a slightly bent one by placing it under a press.

    Use only the “native” adapter with a microSD card. With another adapter, even if you were able to format the phone, you most likely won’t be able to write the information to disk.

    SovetClub.ru

    Instructions: How to remove write protection from a flash drive or SD card - software and hardware

    Despite active use « cloud storage", flash drives remain relevant to this day. With their help, it is convenient to transfer information between computers that, for one reason or another, do not have access to the Internet. In order to protect the flash drive from spontaneous copying to it malicious files, it can be write-protected. This will lead to the fact that when trying to write information to the drive, the user will encounter the error “The disk is write-protected, remove the protection or use another disk.” The drive can be write-protected either mechanically (hardware) or software. Below we will look at how to remove write protection from a flash drive, SD card and other similar drives.

    Differences between software and hardware write protection of flash drives

    Flash drive manufacturers have recently actively used hardware write protection. To do this, a special adapter was installed on the drive body, by sliding which the user could block the flash drive from writing information to it, or unlock it. In USB flash drives this technology has not become particularly widespread, but it is still used on a number of SD cards.

    Please note: To remove the drive's hardware write protection, you need to find the switch on the case, next to which there is the word Lock (or padlock), and move it to the open lock state. If the device does not have such a switch, then write protection is software.

    Software method Protecting a flash drive from writing information to it assumes that the Windows operating system, in accordance with the requirements of the drive controller, blocks the ability to write information. In such a situation, there are several ways to remove write protection, and we will consider them below.

    How to remove software write protection from a flash drive

    Depending on which version of Windows is used, it is advisable to use one or another method to remove software write protection on flash drives.

    Using Group Policy Editor

    IN professional versions operating room Windows systems It is possible to make settings through the Group Policy Editor. In other versions Windows given There is no utility, and you will have to use other methods given below.

    To remove the software write protection of a flash drive through the Group Policy Editor, you need to do the following:


    After that software protection The flash drive will be disabled, and it will be possible to write the necessary information onto it.

    By editing the registry

    Another way to remove the software restriction on writing data from a flash drive is to use the registry editor. This method suitable for any Windows versions. Do the following:


    Using the command line

    In some situations, changes to the registry do not help get rid of the problem with writing information to a flash drive. In such cases, it is recommended to do the following on the command line:


    After all the steps described above, you can try to write new information to the drive; the protection should no longer work.

    OkeyGeek.ru

    How to disable write protection on a memory card and format it

    Memory cards have long been widely used in most different devices, allowing you to additionally obtain the required several gigabytes of memory. However, during use you may encounter such unpleasant problem, as write protection, which causes considerable inconvenience to users. What to do in this case? Fortunately, this problem can be solved quite simply. All you need is a little patience and follow the instructions. In this article, we will take a closer look at how to remove protection and format a memory card. Let's figure it out. Let's go!


    Users ask questions about how to remove the protection of a memory card and format it if necessary

    It's worth starting with the fact that some memory cards have special switch, with which you can enable or disable write protection mode. Be sure to pay attention to this point.

    The Diskpart system utility will help you solve the problem. Launch Command Prompt with administrator rights. This can be done through the Start menu or through the Run window (use the Win+R key combination and enter cmd).


    Commands are entered sequentially

    Once the command line window appears in front of you, enter the following commands to format the micro SD flash drive:

    select disk 0 (instead of “0”, enter the number corresponding to the microSD card, necessary information will be displayed after entering the command “list disk”)

    attributes disk clear readonly

    create partition primary

    format fs=ntfs (or specify fat32 after the “=” sign, it all depends on what file system you want to format the SD card in, some cameras may not support NTFS)

    assign letter=X (X is the letter that will be assigned to the flash drive)


    After formatting is complete, you can assign a drive letter

    If formatting was unsuccessful in this way, try another option, namely doing it through the Group Policy Editor.

    To go to the Group Policy Editor, open the “Run” window by pressing the Win+R key combination, and then write “gpedit.msc” in the input field (without quotes). In the window that opens, go to the “Computer Configuration” section, then open the “Administrative Templates” folder. In it you will find the “System” directory. Navigate to the "Removable Storage Device Access" folder, which is located in this section.


    Finding the required policy setting

    In the list on the right, find the line “Removable drives Prohibit writing”. Double-click on it with the left mouse button and select the “Disabled” mode. Click "OK" to confirm your changes. Then you need to perform the same steps in the “User Configuration” section. The further path consists of folders with exactly the same names. When you reach the desired item, turn it off.


    The procedure in other sections is similar

    After following all the instructions described above, you can format your microSD flash drive without any problems. If the operation fails again, this may mean that the memory card is faulty and you should consider purchasing a new one.

    Now you know how to unlock a micro SD flash drive to format it. This is done very simply and takes only a few minutes. Even if you are a novice user, this operation will not cause you any difficulties. Write in the comments whether the article helped you understand the situation and ask any questions you have about the topic discussed.

    NastroyVse.ru

    8 ways to remove protection from a memory card

    Very often people store on removable drives important information, which may be needed at any time: documents, personal files, etc. Some people store “files for the soul” on a memory card: favorite music, movies, photos. But unfortunately, sometimes the unexpected happens and the flash drive stops working, and then you need to figure out how to remove protection from the memory card.

    Why do removable drives stop working?

    Removable drives can fail for various reasons. Conventionally, they can be divided into five groups:

    • Mechanical failure. Perhaps water got into the case or some kind of physical impact occurred;
    • Logical fault. This may include a request for formatting, a message about deleting information, or a failure in the file system. Such errors often appear due to unsafe removal of the device;
    • Controller malfunction. The malfunction manifests itself as follows: the disc is write-protected, cannot be displayed or read;
    • Electrical or thermal damage. Human factor, unstable power supply, incorrect assembly of components, which causes the drive to overheat;
    • Wearing out flash memory. Due to the fact that the memory of a flash drive is limited by write cycles, after passing this threshold it may become unreadable.

    Removing write protection from MicroSD

    You can remove protection from the card in different ways. First, try removing protection in the editor. Windows registry. To do this, simultaneously press on the keyboard Windows keys+R, type regedit and press Enter. After that, open HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\StorageDevicePolicies, in the WriteProtect data change the value from one to zero. Don't forget to save your changes. At the end of the procedure, disconnect the drive and restart the PC. If this doesn't help, try other methods.

    Unblocking the card

    Place the removable drive on a flat surface with the label facing up. On the left side you will see a small lever for switching - Lock button, which serves to protect the card from accidental erasure. There is no “locker” on microSD, so you need to insert the drive into the adapter and move the lever in the opposite direction until it stops.

    Changing disk properties

    If the drive's protection prevented you from copying the data to another drive, and you need to save it, try the following procedure. Connect the card to your computer, find its name in the list of devices and right-click on it. A menu will drop down, select “Properties”, then “Access”. The following window will open, in it select “Advanced settings” and check the box next to “Share”. Confirm the changes by clicking "Ok".

    Changing the file system

    When writing a file to a storage device larger than 4 GB, an error notification window may appear due to limitations in the file system. If the drive is formatted with FAT32, the data size is one of its write limitations. Change the file system to NTFS. To do this, right-click on the CD disk icon and in the menu that opens, click “Format ...”. Put the file NTFS system and click "Start".

    Removing microSD protection using a mobile device

    Almost all mobile devices latest generation: smartphones, cameras, players, PDAs can format microSD. You can find this option through the settings and format the flash drive directly through the device. The fact is that the device could have memory protection installed to ensure data confidentiality. Remove protection in settings. Of course, all electronic devices have their own characteristics, and if you have any difficulties, read the instructions for your gadget or seek advice from service center.

    We use software

    You can remove write protection using software, while the information on the media will remain intact. Many scripts and utilities have been developed for such an operation, good example- reset.zip. The main thing is to download programs only from trusted sources so as not to bring viruses to your computer. As a last resort, you can perform low-level formatting using the Hard Disk Low Level Format Tool, but it will erase all data from the flash drive. The main advantage of the utility is that it restores the most hopeless drives that have not been formatted Windows tools.

    Perhaps your card has been physically damaged?

    Sometimes it happens that when trying to write new data to the drive, physical damage occurs: the card is slightly bent, one of the contacts on the flash drive or on the adapter itself is dirty, and the microSD shorts it out. If the problem is contamination, clean the contacts with a cotton swab, after moistening it in acetone or an alcohol-containing liquid. If the card is severely bent, it will not be possible to restore it. A slightly curved card can be straightened using a press, but you need to act carefully.

    For a microSD card, you need to use only the native adapter, since with another adapter it is unlikely that you will be able to “upload files”.

    Formatting - if other methods did not help

    If you are unable to access the data on the card, you can try to “revive” the card using formatting. But remember, all information will be deleted.

    Why format the card:

    • Get rid of viruses;
    • If it is impossible to “fill in” large file to disk;
    • The card is slow.

    How to format? Right-click on the flash drive icon. When the context menu opens, select the “format” command.

    Let's sum it up

    We told everything possible ways restoring and removing protection from removable drives. Please note that careful use of the flash drive safe removal from a computer, protection from moisture, etc. will significantly extend the life of the drive and prevent problems from occurring. If your card begins to work incorrectly, choose the right “treatment” - use the above recommendations!

    Comments powered by HyperComments

    HDDiq.ru

    How to remove protection from a memory card?

    A memory card is a small storage device that is used to store digital information. Memory cards are widely used in various electronic devices, including cameras, smartphones, phones, tablets, MP3 players, etc. There are memory cards various formats and sizes, but regardless of this, the same problems may arise when working with them. For example, when you use a flash card in a computer, the latter may tell you that the device is write-protected and it will simply be impossible to write any files to it. Today we will try to solve this problem together.

    Having a problem with a write-protected flash drive? Don't know how to unlock a flash drive and make it readable? You are trying to write some file to a USB drive or SD card, and in response you receive a message: “The flash drive is write-protected.” If you urgently need to copy files to a disk or flash drive, I'll show you how to remove protection and format (or wipe) the storage media - for further work, familiar and correct.

    We use programs to format memory cards and USB flash drives

    Some flash drives come with proprietary software. It works better than standard tools Windows formatting. These programs - not always, but nevertheless - will help remove protection. The downside of this approach is that you lose all the data on the media. So if this is unacceptable to you, move on to the next chapter.

    2. More universal method Forcibly format a USB flash drive / SD card - use formatting utilities like the Hp Disk Format Tool. You can select the file system and formatting type.

    Restoring access to a flash drive through the Registry

    The method of removing write protection is quite simple, but requires minimal skill and careful handling of the registry editor. If you are not 100% sure of your actions, do it using the RegOrganizer program.

    1. Open the Registry Editor as an administrator (Start – regedit).

    2. Go to the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\ directory. If there is no StorageDevicePolicies folder inside this directory, create it. To do this:

    3. Right-click on the current directory Control

    4. From the menu, select New - Partition and name it StorageDevicePolicies.

    5. Right-click on StorageDevicePolicies and select a new value for the DWORD(32-bit) parameter for a 32-bit OS or DWORD(64-bit) for a 64-bit OS, respectively.

    6. Rename the dword parameter to WriteProtect, double-click on the line, specify the value 0 (HEX).

    7. Safely remove the flash drive and restart your computer.

    8. Connect the USB flash drive. If necessary, format it.

    Video version of the instructions:

    Another solution to remove protection from a disk: use the diskpart utility

    diskpart is a console utility included in Windows XP and higher that allows flexible management hard drives, file volumes and partitions at an advanced access level.

    We will try to access the problematic flash drive via the console, and then format the write-protected flash drive.

    1. Open a command prompt (cmd.exe). Type "diskpart" to open the utility.

    2. Type "list disk" to display a list of available disks on the system.

    3. Determine where your USB drive is in the list. Enter "SELECT DISK n", where n is your USB flash drive with a write-protected disk.

    Be very careful! Selecting the wrong media will result in you losing all data on the selected drive.

    4. Type "clean" (you may have to repeat this command twice or three times). If nothing works, try other ways to unlock the flash drive.

    5. Enter "create partition primary" to create a new partition on the USB flash drive.

    6. Enter "select partition" to select a partition on the disk

    7. Type "active" to make the drive active

    8. Enter "format fs=ntfs" to format to NTFS (before formatting the flash drive, make sure you have selected the correct storage medium!).

    By the way, the option with diskpart is one of best methods format a write-protected flash drive without resorting to third-party tools.

    Another way to remove protection from a memory card/flash drive. Diskmgmt.msc utility

    The protection removal method is suitable for both SD memory cards and USB flash drives. To implement it, we will need a standard Windows component for disk management – ​​diskmgmt.msc.

    1. Start – Run. Type diskmgmt.msc into the text line and press Enter
    2. Right button on the partition you want to format (the letter and partition will help you determine)
    3. Select "Delete volume..." and confirm the operation
    4. IN context menu select the "Create Volume" command
    5. Select primary partition
    6. Leave all parameters as default
    7. Click ok

    Removing protection from a flash drive through the Windows Group Policy Editor

    In some cases, access to a flash drive is limited by local Windows Group Policy rights. We tell you how to remove protection in such a situation:

    1. Start – Run – gpedit.msc.
    2. In the panel that opens, go to the following section: “Computer Configuration - Administrative Templates - System - Access to Removable Storage Devices.”
    3. Next you need to deactivate the option “ Removable drives: Deny reading”, switching to the “Disable” state.

    Other working methods for removing file write protection

    If none of the above recipes helped, well, other methods on how to remove protection from a flash drive will probably work (the list will grow over time).

    1. Check your flash drive for viruses. Some malicious applications establish their own control over the files, as a result, the flash drive is protected from writing data belonging to viruses. How to remove protection in this case? For scanning we recommend using .
    2. Check if the flash drive has a hardware button that allows you to physically unlock it (there is a switch on the side that needs to be moved towards the open lock). However, today similar usb flash drives and SD cards are very rare - these are mostly old device models.
    3. Update the firmware of the flash drive, find it on Google exact model You can use chip vendor and chip vendor model, see Device Manager.

    Conclusion. Although it is not always possible to determine why a flash drive is write-protected, of the many methods described, at least one works. If none of the methods for removing protection from a flash drive helped you, all you have to do is replace it usb drive- in other words, buy a new one.

    However, ask questions on the topic - you can do this through sidebar on our website. We'll try to help.

    The media is write protected: what to do? Questions and Answers

    32 GB flash drive WANSENDA when formatted. When you try to delete a file, it asks you to remove write protection from the disk or use another one. What to do, how to remove write protection? I can’t delete or transfer files to a flash drive.

    Answer. Try removing protection from your flash drive through the Registry, using the diskpart or diskmgmt.msc utilities (included in Windows). Format the flash drive special programs- Low level format or Disk format tool (see the beginning of the guide).

    All my formatting attempts produce the same result: remove the protection, the card is write-protected. I removed the protection in every possible way, but it comes back, I can’t do anything. The phone displays information about a card malfunction and cannot format it in any way. The computer and laptop accept it, but formatting fails.

    Can you tell me what to do, how to remove protection from the SD card? Other phones and digital camera didn't help.

    Answer. Try resetting the protection using the methods described in the article and immediately format the memory card to FAT32. Check if there is a switch on the SD card (it may be set in the wrong position, so the memory card is write protected).

    I can’t format a SONY 64GB flash drive, copy or delete files to it. The system says that the disk is write protected. What to do? I tried everything you have. Doesn't help. I bought Flash from Mvideo about 3 months ago, it worked fine before.

    Answer. Some users are helped to remove protection by a proprietary JetFlash utility Recovery. It allows you to format a flash drive at a low access level. If that doesn't help, try removing write protection from the disk through the registry or command line. After this, restart your computer.

    I have a Samsung S3600 phone, it has stopped writing files to the card. The most interesting thing is that there are two photos and one video left on the card - there is NO way to delete them at all. They are deleted from the computer, but then they appear again on the map. I can’t write anything on the card - at first it’s as if everything is there, but on the phone there’s nothing... like nothing. I didn’t drop the phone, I didn’t drown it, the card just suddenly stopped working, and in such a weird way. He sees the card, but does not write anything to it and does not delete anything from it... How to remove write protection on a flash drive?

    Answer. You can remove write protection on a flash drive through forced formatting. This can be done through the console utility diskpart for Windows or various graphical utilities like SDFormatter or Hp disk format tool.

    It is possible that files are not deleted due to errors in reading the sectors on which the files that cannot be deleted are written. You can check the flash drive for errors via Properties - Tools - Check in Explorer.

    After navigating with ADRplayer, I can’t delete files (including write-protected ones) from the SD card. In Windows it is recognized as a 118 MB disk with the ADRplayer program on it. The files are all played by this program. Formatting is not possible in Windows.

    Answer. Since the SD card's disk is write-protected, you need to format it to NTFS via the command line (using the diskpart utility) or using system utility diskmgmt.msc. In addition, there is a wonderful program for SD cards called SDFormatter - it removes write protection.

    It’s not clear what happened to the flash card, when you connect the card to the computer it says “To use the disk in drive J, first format it.” You start formatting in fat32 format without quick cleaning and tried with quick, it says the disk is write protected. I tried the described ones the options didn't help.

    The method via diskmgmt.msc after right-clicking on the flash drive does not allow “delete volume” and other actions are simply not active. The file system of the flash card is Raw, and the system says that it is working. What to do, how to remove write protection from a flash drive and revive it?

    Answer. In addition to diskmgmt.msc, try removing write protection on the flash drive through the Registry or using the diskpart console utility. For formatting, use not standard Windows tools, but, for example, Low level format. If after these manipulations the disk is still write-protected, try opening the flash drive in another operating system, use to manage disks on a flash drive third party software- let's say Acronis Disk Director.

    I bought a mini sd for a 128gig SanDisk phone. I put it in my phone Samsung Galaxy A5 (2016), it works for a while and then it blocks recording to it. No matter what I did: I formatted it via a PC, and via a phone - it was all to no avail, it would work for a while and then it would block the recording again. How to format a protected flash drive?

    Answer. The file table on the memory card may be damaged, making it impossible to write new data. In such cases, it is recommended to check the disk for errors using the standard chkdsk tool (Start - Run - chkdsk). If that doesn't help, format the SD card using the sd formatter desktop application. Judging by the reviews, the utility has helped many users when formatting a flash drive. You can also format the SD card via Recovery menu by rebooting the phone in the appropriate mode and selecting the option Wipe cache partition.

    I ordered a USB flash memory from the Internet. I initially formatted it, but I didn’t like that she didn’t read or see all the formats. I decided to format it completely, without a check mark, just (table of contents). Now a laptop with Windows 10 OS sees it, but requires formatting it. I format it, but the flash drive is not formatted - the disk is write-protected. I’ve already tried to do something (download programs), but I don’t understand, I’m still far from it.

    Answer. In your case, it is advisable not to format the USB flash drive standard means Windows, I use specialized software - fortunately there is a wide choice. First of all, look for programs specifically for your flash drive on the manufacturer’s website. If not found, use HP USB Disk Storage Format Tool or any disk manager like Acronis Disk Director. Specify NTFS or exFAT as the file system.

    1) Sandisk ultra USB 3.0 flash drive 16 GB. I tried everything, from renaming the letter to cleaning the registry. As soon as you start formatting (including through partition management), a message pops up that Windows cannot do this and the flash drive disappears from view. I also tried HDD Low Level Format Tool v4.40 Final - the same thing happens as described above. How to format a write-protected flash drive?

    2) I can't format the micro SD card. Writes: “Windows was unable to complete formatting.” I’ve already tried with different programs, and command line. Still not formatted. I just can't delete files. I clicked “delete”, removed the flash drive and put it back. The file that was deleted is there again. I can’t delete or format.

    Answer. Try other formatting programs: SDFormatter or software available on the developer’s website (sometimes you can use them to format a flash drive bypassing system errors). In addition to Disk Management, you can use any disk manager like Partition Magic or Acronis Disk Director.

    You can also assume that the problem is related to Windows or the computer configuration. Try formatting the flash drive on another computer or in a different OS environment (Windows/Mac OS/Linux).

    There are situations when, when trying to transfer a file to a flash drive or card, Windows memory displays a message stating that the disk is write-protected.

    This is one of the most common problems that may appear during operation. flash drives. Often happens when using your removable media with great regularity during multiple rewrite cycles. However, this also happens with recently purchased flash drives. This means that it is impossible to add or copy any files. How to save the situation in this case?

    There may be several reasons why the message appears: hardware or software recording bans, limit by the number of information rewrites, refill disk, incorrect formatting, damage sectors of the disk memory chip or control microcontroller, malicious software, problems with device drivers, incorrect recognition of the flash drive by the system. Therefore, one universal solution does not exist.

    This instruction will show you several ways to remove protection from a flash drive.

    Removing write protection through the registry

    First of all, make sure that you the file is not protected from the recording, after which you should go to the editor to solve the problem system registry. Launch the window Execute(Win+R), where we enter the word “ regedit».

    Section in the registry HKEY_LOCAL_MACHINE, and we go through the directory tree as follows:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control.

    The parameter we are interested in there is StorageDevicePolicies.

    Set the write protection value in zero as shown in the picture. This can solve the write prohibition problem. Save remove removable media and reboot computer.

    However, this setting may not be in the registry. Then it's need to create– in the appropriate section, right-click Create, select an option DWORD(depending on the bit depth of Windows used) and name StorageDevicePolicies.

    Give the parameter a name WriteProtect and set the value to zero. Perform the steps mentioned earlier (save, remove media, reboot) and check if the problem has disappeared.

    Using the command line

    The next troubleshooting method involves using command interpreter on behalf of the administrator. In the button Start Right-click on the corresponding field.

    We write there the word “ Diskpart", then " list disk».

    And we look What number disk on our flash drive. In my case, this is disk 2. We write “ select" And number which you see.

    After this we enter the command: attributes disk clear readonly And exit.

    This removes the read-only option from the flash drive. We try to copy something onto a flash drive, if this doesn’t help, move on to the next point.

    Removing blocking using group policies

    Should be used group policy editor. We launch it in the same window Execute.

    Let's go through the guide " Computer configuration» - « Administrative Templates» - « System» - « Access to removable storage devices». Disable write prohibition function for removable drives. That is, switch the property to the status “ Disabled».

    After this, when you try to write, your disk will not generate errors. Otherwise, it may well be that the flash drive is simply faulty.

    If the SD card is write protected

    In a similar situation with a memory card, there is another option locked write protection lever.

    In some SD cards, and even flash drives such are found, it is possible hardware lock records. The switch is usually located on the side of the device. There you will find the inscription Lock and a closed or open padlock icon.

    Move the lever to opposite position and mechanical protection removed. To re-block we do reverse actions. As you can see, everything is quite simple.

    If the previous tips did not help you, try format your removable media, unless there is a prohibition on this action.

    If you are using a flash drive or memory card from Transend, then to restore the recording to the disk, you can use proprietary program Transcend JetFlash Online Recovery.

    Companies such as: Silicon Power, Adata, Kingston and others. Find out if such software exists on the website of the manufacturer of your removable media. Usually their use is not difficult and all actions are intuitive.

    Now you have many working methods for solving this problem in your arsenal.

    Often, users from all over the world are faced with the fact that it becomes impossible to work with a memory card due to the fact that it is protected. At the same time, users see a message "Disk is write protected". Very rarely, but still there are cases when no message is visible, but it is simply impossible to record or copy anything from microSD/SD. In any case, in our guide you will find a way to solve this problem.

    Almost all of the methods described below are quite simple. Fortunately, this problem is far from the most serious.

    Method 1: Use a switch

    Usually there is a switch on microSD or card readers for them, as well as on large SD cards. He is responsible for write/copy protection. Often on the device itself it is written which position means what value "closed", that is "lock". If you don't know, just try switching it and again try inserting it into the computer and copying the information.

    Method 2: Formatting

    It happens that the SD card has been seriously affected by a virus or has been affected by mechanical damage. Then the problem under consideration can be solved the only way, and specifically formatting. After performing this action, the memory card will be like new and all data on it will be erased.

    Read our lesson to learn how to format a card.

    If formatting fails for some reason, use our instructions for such cases.

    Method 3: Cleaning contacts

    Sometimes the problem with imaginary protection occurs because the contacts are very dirty. In this case, it is best to clean them. This is done with ordinary cotton wool and alcohol. The photo below shows what contacts we are talking about.


    If all else fails, it is best to contact a service center for help. You can find it on the official website of the manufacturer of your memory card. If nothing helps, write about it in the comments. We will definitely help.

    The era of floppy disks has already sunk into oblivion; now people everywhere use new generation drives - flash drives. This device is compact and can hold a large amount of data. But even flash drives are far from perfect. Quite often when working with flash media, problems arise. various problems. For example, the most common error is that when working with a storage medium, the OS writes “The disk is write protected.” What does this mean, and how to remove write protection from a flash drive? We will talk about this in this article.

    Flash drive protection may be hardware or software based. It is for this reason that there are many ways to remove write protection. Let's talk about each in more detail.

    If you don’t know how to remove protection from a memory card or flash drive, then first turn your attention to the device’s case. Most likely the root of the problem is mechanical protection. Each MicroSD card and some flash drives have a special switch on the case. It is responsible for activating write protection. Surely the switch in your pocket changed its position, which led to problems. It's all very easy to fix. You just need to change the position of the switch.

    In addition, it is worth checking the functionality of the flash drive. To do this, try connecting it to a different port. It’s better to test the drive on another PC, if possible. If everything is in order, then the problem lies in the software.

    Software problems

    If the device works correctly and the mechanical switch is in the correct position, you need to know how to remove protection from the disk programmatically. There are several ways to do this. Let's look at them in more detail.

    NTFS formatting

    By default, the flash drive is formatted in FAT32. However, this file system has one limitation that few people know about: the maximum amount of recorded data should not exceed 4 GB. This leads to a rather ambiguous situation. On the one hand, writing is allowed, but on the other hand, due to FAT32, it is impossible to upload a large file to a flash drive.

    To remove write protection from a flash drive, you need to format the drive and change the file system from FAT32 to NTFS. There are no restrictions regarding the amount of data recorded. Therefore, the question of how to unlock a flash drive will disappear by itself. To change the file system, you need to connect the drive to the PC and go to “Computer”. Before you save its contents to your PC.

    Find your device there and right-click on it. Select "Format" from the drop-down list. A new dialog will open in which, next to the “File system” inscription, you need to set the NTFS option. Once done, click on “Get Started”. The formatting process will start, during which all data from the drive will be deleted and the file system will change to NTFS.

    It is recommended to remove the flash drive from the USB connector using “safe removal”. However, when it comes to NTFS, this is not a recommendation, but a strict rule that must be followed. Otherwise, you risk harming your device.

    Windows Registry

    It's no secret that the registry is a real lifesaver for any Windows OS user. Using this section you can solve almost any problem. Locking a storage device is no exception. How to fix this problem? To remove protection from a flash drive or microSD, you must perform the following manipulations:


    Sometimes the StorageDevicePolicies section may simply not be on your PC. How can you remove protection from a flash drive in this case? Just create StorageDevicePolicies manually. Right-click on the previous directory (in our case it is Control), then in the menu that appears, click on “Create”, and then select “Partition”. The system will prompt you to enter a name. We drive in StorageDevicePolicies there, after which we create a section.

    Next, you need to go to the directory that appears and right-click on the menu located on the right. In the list that appears, click on “Create”, and then select the “DWORD Value” option. We select the bitness characteristic depending on your system (64 or 32 bits). New parameter call WriteProtect and set its value to 0. Again, reboot the PC and check whether the information is written to the flash drive.

    Group Policy

    If the disk is protected and it was not possible to fix it through the registry, you need to check group policy. Perhaps it is she who prohibits writing data to the media. To test the policy, you need to do the following:


    Command line

    Another way to remove protection if the flash drive is write-protected is to interact with the command panel. To restore correct operation flash drive, follow these instructions:


    After completing all the steps described above, the notification that the flash drive is write-protected should no longer bother you.

    Software

    Flash drive manufacturers take care of their customers by creating special utilities, which are able to restore problematic devices. If you are faced with the fact that the flash drive is not formatted, cannot be written, etc., then simply use a proprietary program. It is worth noting that when choosing software to restore the functionality of a flash drive, you need to pay attention to the manufacturing company. If you use devices from Transcend, then a program called JetFlash Recovery is suitable for you; owners of flash drives from Silicon Power should use USB Flash Drive Recovery, etc. You can download the utility from the manufacturer’s official website.

    In addition, there are a lot third party programs, which also allow you to solve recording problems. Among such utilities, it is worth highlighting D-Soft, Flash Doctor, etc. As a rule, the process of restoring a flash drive using these programs is simple and straightforward. You need to configure the formatting parameters and click on “Start”. Once the cleaning is complete, the flash drive's protection will be deactivated and you will be able to write various information to the device.

    Virus

    If none of the above methods helped, then the root of the problem is probably malicious software that has “settled” on your drive. In the vastness World Wide Web a lot of viruses. And some of them are capable of blocking writing to a flash drive.

    What to do if there is a virus on the drive? Get rid of it using one of the modern antiviruses. Arrange and then delete potentially dangerous files. After this, the recording problem should be resolved.

    Read more: