The monitor does not turn on and says it is in energy saving mode. Windows Energy Saving Modes

Almost every operating system provides a power-saving mode. Despite the relevance and usefulness of this function, it is not always useful. U modern user Moments occur repeatedly when processing information directly by the computer, reinstalling the system, software, downloading files from the Internet, and suddenly... the computer went out. You have to do the work again, and it’s good if the information and data can be restored, and a sudden stop in work will not harm the system process.

If you do not need to disable the energy saving mode, it would be better to leave it. Saving electricity, maintaining the functionality of the monitor, increasing the service life - these are the priorities that are the result of a careful attitude.

Power saving modes (and the ability to configure them) first appeared in Windows 98 and are currently present in every operating system.

Their use is associated with the possible need to save battery power (as, for example, in laptops), they can be used as one of the options for completing work (the next time you turn it on, it will take less time), as well as to save electricity consumption (imagine how much the bill can decrease enterprise, if it has several hundred PCs).

In this article we will look at how to install, how to choose one of existing options, and also how to disable the energy-saving mode on your computer.

In principle, greatest number Energy in a running computer is spent to support the operation of the monitor and hard drive.

Monitor states

At regular work of the monitor, both of its blocks are active - horizontal and vertical scan. This mode is called normal (Normal) and consumption is up to one hundred watts.

Almost instantly, the display will return to operation from the Stand-by state, in which horizontal scanning is turned off and consumption is reduced to ninety percent of normal.

When switching to Suspend mode, only vertical scanning will be disabled, the consumption will drop to ten to fifteen percent, but the monitor will also take a little longer to come out of it.

Using the Power-off mode entails turning off both scanners, while power consumption is reduced to a minimum of five percent. But also a return to normal operation will take the same amount of time as turning it on from a “cold” state.

Metamorphoses of the hard drive

The computer switches to Stand-by mode after saving the intermediate results of the work open applications V RAM. At the same time, an appeal to hard drive stops.

The Hibernate state differs from the previous one in that the entire state of the OS at a certain moment will be captured on the hard drive (and not in the RAM), to which it will return the next time it is turned on.

New Hybrid Sleep mode for the first time Windows Vista combines the features and consequences of both previous ones - both storing open application files in RAM and the system state in the “hiberfil.sys” file on the hard drive.

Activating Power Saving in Windows

On Windows 7, three power modes have been present in the consumption settings since Vista. Up to Windows 10, the energy saving mode is represented (in Russian transcription) by three options: “Sleep”, “Hibernation” and “Hybrid Sleep”.

They correspond to the Stand-by, Hibernate and Hybrid Sleep states discussed above.

However, please note that not all motherboards and video cards have energy saving support.

Also, this feature may be disabled in the BIOS or in the system settings.

As for other operating systems, on Mac you can enable the required mode by using the “Energy Saving” tab in “ System settings" In Linux, the appropriate commands (setterm, xset...) are entered through the console.

Selecting a mode in Windows 10

To put your PC into one of the gentle modes on Windows, you need to use the following algorithm of actions:

After activating the Start button menu, place the cursor on the “Shutdown” line (it may have the name “Shutdown”). In this case, an additional menu will appear in which the cursor will need to be positioned on the “Sleep mode” key:

Similar actions will lead us to the “Hibernation” mode. Just press another key:

The hybrid sleep state is more complicated. On laptops it will be disabled by default.

To activate it, you first need to go to the tray icon with the image of the battery (since on laptops using OS Windows settings energy consumption are displayed in the System tray):

By right-clicking we will open from the “Power Options” menu that appears:

The following control dialog will open in front of us:

The checkbox in it will correspond to the currently used parameters.

Having moved to “Settings”, you need to turn on the plus sign next to “Sleep” and enable the “Hybrid Sleep” option so that the value is “on.” corresponded to the picture:

After such activation, the “Sleep Mode” button in the “Start” menu will no longer put your computer into simple “Sleep”, but into “Hybrid”.

Wake-up of the PC from any state associated with reducing power consumption is done by pressing the power button (although to wake it from normal “Sleep”, just move the mouse or press any of the keyboard buttons).

Setting up an energy saving plan

In addition to the standard ones, on any computer it is possible to fine-tune acceptable power consumption modes. This is typical mainly for computers powered by batteries (since stationary ones always work connected to the network at maximum).

The transition to the parameters is carried out by the already mentioned method of calling “Power Options” from the tray.

The parameters available for adjustment are opened by clicking on the section shown in the following figure:

Here we get to the list of all possible schemes:

Separately, it should be said that in addition to operating system schemes, those that correspond to installed applications from your laptop manufacturer (in in this case"Power4Gear").

The enabled checkbox corresponds to the one used in at the moment scheme.

If your laptop runs alternately on battery power and mains power, then it is logical to create your own power supply to avoid alternating between switching on balanced and maximum.

To do this, in the “Power Supplies” window, place the cursor on “Creating a circuit...”:

We connect the checkbox opposite any of the existing ones (no matter which one) (1), enter a name for the new scheme to be created (2), activate the “Next” button (3):

We will have direct access to the three main settings and to changing the list of additional ones:

Availability for their adjustment is enabled, as shown in the picture:

Each section opens by clicking on “+”. Also, for each, a value is set for operation from the mains and from the battery. For example, for a hard disk partition.

In general, you need to carefully go through all sections additional settings, analyze the expected events and place all the checkboxes in accordance with the need and with your own vision of your work or habits. Don't forget that for more simple solution To learn how to exit Power Saving Mode, you will need to carefully review the Power Buttons and Cover section.

Virtually every operating system includes power management tools. Energy saving mode- a useful function, but it will be out of place when the computer performs main tasks.

You will need

• A computer with a pre-installed Windows operating system.

Instructions

1. To disable this option on Windows 98/Millenium/2000 operating systems, click the “Start” button and open the “Control Panel” applet. In the window that opens, double-click on the “Power Management” shortcut. Here you need to choose a power management scheme with settings that will be optimal for your computer. Go to the line "Disable monitor" and select "Never". To save the settings, click the “Apply” and “OK” buttons.

2. In Windows XP, you should also launch the Control Panel, the shortcut for which is located in the Start menu. Select either Power Options or Productivity and Maintenance, and then Power Options. In the window that opens, go to the “Power Management Schemes” tab and select the desired one mode .

3. For desktop computer It is recommended to prefer “Home/Desktop” and “Portable” for portable devices. On the contrary, the options “Disconnect Disks” and “Display Disconnect” should be preferred to “Never”. To save the changes, click the “Apply” and “OK” buttons.

4. For operating rooms Windows systems Vista/Seven in the “Control Panel” you need to open “System and Maintenance” and select the “Power Options” item. In the window that opens, select a power plan and click on the “Change plan settings” link.

5. Go to the Advanced Options applet and click the Edit button. Here you need to reveal the elements “Sleep later...” and “Sleeping mode» select the “Never” option.

6. A similar action must be performed with the drop-down parameters “Hibernate later...” and “Turn off the screen later...” (Tab “Screen”) - prefer the value “Never”.

7. In order to close the current window and save the metamorphoses, step by step click the “OK” and “Save” buttons.

Disabling your monitor's power management option will prevent it from going into sleep mode after a certain period of inactivity. Sleep mode is a feature aimed at reducing energy consumption. But it happens that the computer turns on sleep mode when it is in the middle of solving tasks such as backup hard drive, checking the system for viruses or reforming huge multimedia files into a different format. Absolutely, in this case this function should be disabled.

Instructions

1. Windows XP Click the "Start" button located in the lower left corner of the screen. Select the “Control Panel” link. Control panel applied to metamorphosis different settings Windows XP. In the classic Start menu, double-click the Power Options button. If you have a Start menu by category, select Productivity and Maintenance, Power Options. On the Properties: Power tabs, you can manage your screen's power settings and hard drives, as well as configure the Source Uninterruptible Power, if you have one. Select the “Home/Desktop” section in the “Power Plans” tab. Select "Never" for "turn off display" and "turn off drives". Click the “Apply” button, and then the “OK” button.

2. Windows 98/ME/2000 Windows 98/ME/2000 Click the Start button, select Control Panel and locate the Power Management or Power Options icon in Control Panel Settings. Select the Power Options tab if it is not yet selected. From the drop-down menu labeled “Turn off the monitor,” select “Never.” Click "Apply" and "OK".

All modern operating systems include a power management subsystem. The core function of this subsystem is to implement energy saving by shutting down or entering a low power state peripheral devices or even each computer during a long period of inactivity by the user. This function extremely suitable. However, if you need to ensure the continuous likelihood of a rapid response from the computer to user actions, you should disable mode energy saving .

You will need

• - administrative rights in Windows.

Instructions

1. Open the Control Panel window. To do this, click on the “Start” button (located on the taskbar). In the menu that appears, select “Settings”. In the child menu that appears, click on the “Control Panel” item.

2. Open the dialog for setting the operating parameters of the power management subsystem. In the list of shortcuts in the Control Panel window, find the item “Power Options”. Select it. Right-click on the element. In the appeared context menu select "Open". You can also double-click on a shortcut. The “Properties: Power Options” dialog will open.

3. Do new scheme power management. In the "Properties: Power Options" dialog, switch to the "Power Management Schemes" tab. Click the "Save As" button. In the “Save Scheme” dialog, enter a new unique name for the scheme. Let's say, "Without energy saving". Click OK.

4. Edit the schema you just added. In the list located in the “Power management schemes” group, select the element that corresponds to the diagram you made. In the lists “Turning off the display”, “Turning off disks”, “Pending mode via", "Sleeping mode through" located in the "Scheme settings..." group, select the elements with the text "never".

5. Disable mode energy saving. In the “Properties: Power Options” dialog, click the “Apply” button. The settings of the selected scheme will be saved. Also, the current circuit will be selected as used to control the computer's power. In accordance with the selected settings, the computer's display and hard drives will not turn off whenever the user is inactive for any length of time. Also, the computer will never be put into standby or sleep mode. mode. After completing all the described actions, click the “OK” button. Close the control panel.

Useful advice
Turning off the monitor during periods of long periods of absence can significantly extend its life.

From settings monitor The ease of working on a computer depends on it. If the wrong settings are selected, this can result not only in an unbreakable feeling of irritation and nervousness, but also in headaches, decreased visual acuity, and nausea. In order to change parameters monitor, take advantage of the probabilities of the system or your video card.

Instructions

1. To change the size of windows, fonts, icons, and window appearance, open Control Panel through the Start menu. Under Appearance and Themes, select the Display icon. Or, right-click in any place on the desktop that is free from files and folders, and in the drop-down menu, left-click on “Properties”. The Display Properties dialog box opens.

2. The overall design of the desktop, the appearance of folders and the Start menu is configured on the Themes tab. At the bottom of the window you will see a visual representation of the selected theme. Using the drop-down list, select the topic that you like. To install a custom theme, select “Browse” and specify the path to the desired theme. Click the "Apply" button.

3. Adjust the image size on the monitor on the Settings tab. In the “Screen Resolution” section, use the “sliders” to select a resolution that is comfortable for your eyes. Click the "Apply" button and confirm your selection. For tube monitors, set the screen refresh rate (screen flicker). To do this, on the current tab, click the “Advanced” button. In the window that opens, go to the “Monitor” tab. Check the “Hide modes that the monitor cannot use” box. Using the drop-down list, set the desired frequency. Click OK and Apply.

4. Customize additional folder design, font size and smoothing on the “Design” tab using the “Advanced” button. On the Desktop tab, set background picture, preferring it from the drop-down list, or click the "Browse" button and specify the path to the custom image. Custom icons For standard folders install by clicking the "Customize Desktop" and "Change Icon" button.

5. Open your video card settings control panel. Adjust the color, brightness and contrast of the image on the corresponding tab. You can also adjust the contrast using the system options. Through the start menu, call up the “Control Panel”, click on the “Special Probabilities” icon, in the window that opens, go to the “Screen” tab. With support for Customize button and drop-down list, set a combination of colors and fonts that is easy on the eyes. Confirm your selection and close the window.

Video on the topic

Studio monitors are one of the essential elements in sound recording and mixing. They provide an opportunity to evaluate the sound of a particular composition and eliminate frequency gaps.

Instructions

1. Search the Internet for all possible options to choose studio monitors. Essentially, these are the same computer speakers, only with the widest possible range of sound. Their main difference from traditional household acoustics is the virtual absence of gaps in the frequency interval, i.e. if on yours computer speakers the frequency range from 20 Hz to 44 kHz is indicated, this does not mean that they cover it completely, unlike professional studio monitors.

2. Read on recording forums. There is probably a corresponding discussion thread where knowledgeable users We were considering one or another option for studio monitors. Read the presentation of several systems, then try to find out how much they cost.

3. Go to a music equipment store to get your bearings and pick up studio monitors. The sales assistant will be able to advise you on a multifunctional option in terms of price-quality ratio. Please note that such equipment needs to be purchased a little “for growth”. If you now buy relatively inexpensive studio monitors, then in a few years they may no longer be enough for you, because your sound engineering skills and sound requirements will certainly increase.

4. Also consider the option of studio monitors and headphones. They look no different from ordinary bulky headphones, but their sound will probably pleasantly surprise you. Cool studio headphones are slightly cheaper than cool studio monitors, but they have one significant advantage: their sound is not affected by room acoustics. Even if the room has poor sound insulation or is completely absent, the headphones will sound wonderful, unlike studio monitors, the clear sound of which may be (albeit slightly) added to room noise and echo.

Video on the topic

You should only open the monitor case in special cases and if you have the appropriate skills to work with equipment. If certain malfunctions occur, it is best to immediately take it to the service center and do not do repairs at home.

You will need

• - Phillips screwdriver;
• - flat screwdriver;
• — a plastic card or a mild knife.

Instructions

1. Discover your model's statement monitor on the Internet or check yourself to see if glue was used to hold the walls together frame A. Prepare your work surface, taking into account the fact that you will have to place the matrix on it during disassembly.

2. Disconnect the monitor from the computer, power source, remove all connected wires from its connectors and inspect it frame, check for the presence of fastening elements (in some models they can be hidden with special plugs); they are usually located on the back wall of the device.

3. Unscrew the mounting bolts and remove the monitor from the stand. If you have certain problems with the latter, read on the first pages of the user's manual how to correctly remove the monitor from the stand in your case (usually special latches are used that you need to press and pull the stand).

4. Pry up frame monitor using a flat-head screwdriver or a non-sharp table knife. If it is made of very thick plastic, do not use them, first try removing the cover frame but with your hands.

5. If in your model monitor glue was used to hold the parts together frame a, use a wide flat-head screwdriver. Install it at the junction of the sides frame a, installing it in a vertical position. Lightly hit the screwdriver handle from above until you hear the classic cracking sound. It would be better for everyone not to make major efforts here in order to open monitor, because it can lead to breakdown frame and damage to internal components.

6. Next pry frame monitor around the perimeter using a plastic card and open back cover. For subsequent disassembly monitor, if necessary, download the special service instructions for your model and do not proceed with independent repairs without it.

Useful advice
Do not open the monitor case until the expiration date has expired. warranty period.

Modern lamps, saving energy, later burnouts become a type of household waste with a higher threat class. This is why they need to be properly disposed of. For recycling, special collection points for burnt-out waste are provided in all cities and other residential areas of the country. energy saving lamps.

Instructions

1. The lamps contain internal structure up to 5 mg of mercury vapor. If a lamp accidentally breaks in an apartment, in a trash can or in a public trash bin, it will have a toxic effect on the inhabitants of the house and on the state of wildlife. It was therefore initially recommended that with the production of similar lamps, they should be handed over to points for subsequent industrial recycling after completion.

2. In order to properly dispose of an energy-saving lamp, pack it after it burns out in its own packaging or other cardboard packaging, where it will not break. You can wrap several burnt out lamps in paper and place them in one box. Now you need to find collection points for such lamps in your city.

3. Not all points accept used lamps from individuals. Some exist intentionally to accept large quantities of non-functioning lamps from huge businesses.

4. In all cities, fluorescent lamps are accepted at regional DEZs and REUs. For them, special containers with a signature are installed on the territory of such enterprises. If you do not find a container, ask the administration of the enterprise how you can dispose of the lamp. The city's environmental cleaning services are also required to accept for recycling not only mercury lamps, but also those who have served mercury thermometers, disposable batteries.

5. The problem with the delivery and acceptance of energy-saving lamps and other devices containing mercury has become so serious that in some Russian cities, city district prosecutor's offices have turned to the courts with a request to organize collection points for such raw materials through HOAs. In turn, the courts ordered the HOA to install containers and collection points for used lamps. Therefore, you can ask a reasonable question in your HOA where you can return used lamps.

To connect the monitor to a computer, one of the currently existing interfaces (DVI, D-SUB (VGS), HDMI, DisplayPort) can be used, depending on which one is available on the monitor. You can figure out which one is better to use only by understanding how they differ.

VGA input (D-SUB 15)

One of the first interfaces for connecting a computer and a monitor, the one that transmits analog signal in color RGB scheme together with frequency sweep signals horizontally and vertically. This interface developed for use in monitors with cathode ray tubes. Connector preferred blue has 15 contacts arranged in three rows. The entire row is shifted relative to its neighbors so that the contacts are arranged in a checkerboard pattern. The connector body is trapezoidal in shape so as not to confuse the orientation of the mating connector when connecting. The connector is called D-SUB, while VGA defines the signal format. IN LCD monitors You can use this output, but in terms of performance it is inferior to digital ones. DVI input

The digital input of the monitor is the one that was developed for flat monitors with matrices, in which each pixel is represented by a separate fixed element. The connector has a rectangular shape with beveled corners on one side and two separate groups of contacts. The main group is 24 contacts located on 3 rows, the smaller group is 4 contacts located to the side and divided by a slot, which is also a lock. DVI input is rated for purchase digital signal from the video card. It is unlikely that you will find a CRT monitor with a DVI input. The interface was originally developed specifically for use in LCD monitors, plasmas and other similar devices, where it is possible to transmit the signal from the video card to the matrix without additional reforms. In order not to confuse or insert the connecting wire connector on the wrong side, there are bevels on one side of the connector and an additional slot on the side of the core group of contacts. The DVI connector can also transmit an analog signal (DVI-A, DVI-I). There are separate wires and adapters for all valid connections. It is important not to confuse them when connecting.

HDMI input

A connector that appeared during the subsequent formation digital interfaces for monitors and other multimedia equipment. Main specifics given input is the probability of transmitting not only a digital video signal, but also sound. The connector itself is flat, rectangular shape, inside of which there is a tongue with contact pads on both sides. To orient the mating connector, the connecting cable has characteristic bevels on one side of the connector. The bevels are not straight, but slightly rounded, concave into the connector. With help HDMI interface You can connect several monitors at once or combine a monitor and, say, a home theater.

DisplayPort input

The connector was designed for a format that is actually similar to HDMI; the information transfer speeds and the shape of the connector are slightly different. Its shape is rectangular and flat. The lock is the beveled corners on one of the short sides. Externally, the connectors of the last two types are identical in size, however, the presence of completely different locks will not allow you to confuse them and insert a connecting wire of the wrong format.

Video on the topic

Instructions

To disable this option on Windows 98/Millenium/2000 operating systems, click the "Start" button and open the "Control Panel" applet. In the window that opens, double-click on the “Power Management” shortcut. Here you need to select a power management scheme with settings that will be optimal for your computer. Go to the line "Disable monitor" and select "Never". To save the settings, click the “Apply” and “OK” buttons.

In Windows XP, you should also launch the Control Panel, the shortcut for which is located in the Start menu. Select either "Power Options" or "Performance and Maintenance" and then "Power Options." In the window that opens, go to the “Power Schemes” tab and select the desired one mode.

It is recommended to select “Home/Desktop” for a desktop computer, and “Portable” for portable devices. Opposite the “Disconnect Disks” and “Display Disconnect” options, you must select “Never”. To save the changes, click the “Apply” and “OK” buttons.

For Windows Vista/Seven operating systems, in the “Control Panel” you need to open “System and Maintenance” and select “Power Options”. In the window that opens, select a power plan and click on the “Change plan settings” link.

A similar action must be performed with the drop-down parameters “Hibernation after...” and “Turn off the screen after...” (the “Screen” tab) - select the value “Never”.

Useful advice

Turning off the monitor during periods of long periods of absence from the user can significantly extend its life.

From settings monitor The comfort of working on a computer depends on it. If the wrong settings are selected, this can result not only in an eternal feeling of irritation and nervousness, but also in headaches, decreased visual acuity, and nausea. To change parameters monitor, take advantage of the capabilities of the system or your video card.

Instructions

To change the size of windows, fonts, icons, and window appearance, open Control Panel from the Start menu. Under Appearance and Themes, select the Display icon. Or right-click in any place on the desktop that is free from files and folders, and in the drop-down menu, left-click on “Properties”. The Display Properties dialog box opens.

The general design of the desktop, the appearance of folders and the Start menu are configured on the Themes tab. At the bottom of the window you will see a visual representation of the selected theme. Use the drop-down list to select the topic you like. To install a custom theme, select Browse and navigate to the theme you want. Click the "Apply" button.

Adjust the image size on the monitor on the Settings tab. In the “Screen Resolution” section, use the “sliders” to select a resolution that is comfortable for your eyes. Click the "Apply" button and confirm your choice. For tube monitors, set the screen refresh rate (screen flicker). To do this, on the current tab, click the “Advanced” button. In the window that opens, go to the “Monitor” tab. Check the "Hide modes that the monitor cannot use" box. Use the drop-down list to set the desired frequency. Click OK and Apply.

Customize additional folder design, font size and smoothing on the “Design” tab using the “Advanced” button. On the Desktop tab, set a background image by selecting it from the drop-down list, or click the Browse button and specify the path to a custom image. Set custom icons for standard folders by clicking the “Customize Desktop” and “Change Icon” buttons.

Open your video card settings control panel. Adjust the color, brightness and contrast of the image on the corresponding tab. You can also adjust the contrast using the system options. Through the start menu, open “Control Panel”, click on the “ Accessibility", in the window that opens, go to the "Screen" tab. Using the “Customize” button and the drop-down list, set a combination of colors and fonts that is comfortable for the eyes. Confirm your choice and close the window.

Video on the topic

Sources:

• how to change screen settings

Studio monitors are one of the most important elements in sound recording and mixing. They provide an opportunity to evaluate the sound of a particular composition and eliminate frequency gaps.

Instructions

Search everything on the Internet possible options to select studio monitors. Essentially, these are the same computer speakers, only with the widest possible range of sound. Their main difference from ordinary household acoustics is the virtual absence of gaps in the frequency interval, i.e. If your computer speakers indicate a frequency range of 20 Hz to 44 kHz, this does not mean that they cover it completely, unlike professional studio monitors.

Read on recording forums. There probably is a corresponding discussion thread where knowledgeable users considered one or another option for studio monitors. Read descriptions of several systems, then try to find out how much they cost.

Go to a music equipment store to get your bearings and pick up studio monitors. A sales consultant will be able to advise you on a universal option in terms of price-quality ratio. Please note that such equipment needs to be purchased a little “for growth”. If you buy relatively cheap studio monitors now, then in a few years they may no longer be enough for you, since your sound engineering experience and sound requirements will certainly increase.

Also consider the option of studio monitors and headphones. They look no different from ordinary massive headphones, but their sound will certainly pleasantly surprise you. Good studio headphones are somewhat cheaper than good studio monitors, especially since they have one significant advantage: their sound is not affected by room acoustics. Even if the room has poor sound insulation or no sound at all, the headphones will sound excellent, unlike studio monitors, the clear sound of which may be (albeit slightly) added to room hum and echo.

Video on the topic

Open the monitor case only in special cases and if you have the appropriate skills to work with equipment. If certain malfunctions occur, it is best to immediately take it to a service center and not repair it at home.

You will need

• - Phillips screwdriver;
• - flat screwdriver;
• - a plastic card or a mild knife.

Instructions

Find your model description monitor on the Internet or check yourself to see if glue was used to hold the walls together frame A. Prepare your work surface, taking into account the fact that you will have to place the matrix on it during disassembly.

Disconnect the monitor from the computer, power source, remove all connected wires from its connectors and inspect it frame, check for the presence of fastening elements (in some models they may be hidden with special plugs); they are usually located on the back wall of the device.

Unscrew the mounting bolts and remove the monitor from the stand. If you have certain problems with the latter, read on the first pages of the user manual how to properly remove the monitor from the stand in your case (usually special latches are used that you need to press and pull the stand).

Pry up frame monitor using a flat-head screwdriver or a mild table knife. In case it is made of very thick plastic, do not use them, first try removing the cover frame A .

If in your model monitor glue was used to hold the parts together frame a, use a wide flat-head screwdriver. Install it at the junction of the sides frame a, installing it in a vertical position. Lightly hit the screwdriver handle from above until you hear a characteristic cracking sound. It's best not to make much effort here to open monitor as this may cause damage frame and damage to internal components.

Next, pry frame monitor around the perimeter using a plastic card and open the back cover. For further disassembly monitor, if necessary, download the special service instructions for your model and do not proceed without it self-repair.

Useful advice

Do not open the monitor case until the warranty period has expired.

Modern energy-saving lamps, after burning out, become a type of household waste with a higher hazard class. This is why they need to be disposed of correctly. For disposal in all cities and other residential areas of the country, there are special items reception of burnt out energy saving light bulbs.

The problem of delivery and acceptance of energy-saving lamps and other devices containing mercury has become so serious that in some Russian cities, city district prosecutor's offices have asked the courts to organize collection points for such raw materials through HOAs. In turn, the courts ordered the HOA to install containers and collection points for used lamps. Therefore, you can ask a reasonable question in your HOA where you can return used lamps.

To connect the monitor to a computer, one of the currently existing interfaces (DVI, D-SUB (VGS), HDMI, DisplayPort) can be used, depending on which one is available on the monitor. You can figure out which one is better to use only by understanding how they differ.

VGA input (D-SUB 15)

DVI input

The DVI connector can also transmit an analog signal (DVI-A, DVI-I). For each of possible connections There are separate wires and adapters. It is important not to confuse them when connecting.

HDMI input

Using the HDMI interface, you can connect several monitors at once or combine a monitor and, for example, a home theater.

DisplayPort input

Video on the topic