Settings in TV mode – BBK LT2003S Operating Instructions. Review, testing and configuration of DVB-T2 receiver BBK SMP127HDT2

There are many additional devices that help turn your TV into a device for watching movies and listening. musical compositions. One such device is DVD player, which is capable of playing audio and video files from optical media, as well as from external USB storage devices. Before you connect a DVD to your TV, check out what experts have to say about it. They will help you do this without any extra effort.

Connection method

To properly organize such a connection, you need to determine which connectors are present on both devices: the TV and the DVD player. Depending on the age of the equipment, connectors can vary greatly. Below is a list of all popular connection types:

• HDMI cable. The best connector with high quality video and audio signal transmission. There is the newest generation, called mini HDMI, which has the same qualities as the standard connector, but has a much smaller plug size. Having settled on this method: version 2.0 or higher, marked “high speed with ethernet” and only from well-known manufacturers;

• RCA cord. For many years it has remained a popular connection method for many multimedia devices, including DVD player. RCA is popularly called “tulips”, and the sockets themselves consist of three holes, white (left audio channel), red (right audio channel), yellow (video channel). There is no difference between the RCA output and input, as well as on the cord (there are three tulips on both sides, corresponding to the flower sockets);

• SCART. This is the so-called bus, which transmits sound and image better than RCA, but worse than HDMI. Almost every multimedia device has such a connector, and nowadays, if you want, you can easily connect a DVD to an old TV by purchasing a SCART-RCA adapter;

• S-video. This connection transmits only the image; the sound will have to be connected separately, using a cord with tulips or a 3.5 mm jack. If, for example, the player has an S-video output, but the TV only has an antenna input, then you can use an S-video-RF adapter.

Useful adapters

Very often there are situations when there are no identical connectors between two devices, so how can you connect the DVD to the TV in this case? It's very simple, you just need to select the appropriate adapters. Here is a list of the most common configurations:

1. SCART-RCA. In this option, it is necessary to connect only one adapter, since both plugs are capable of transmitting both sound and image;
2. SCART-S-video+2RCA. Since S-video does not transmit audio signal, it is necessary to connect a 2RCA cable separately;
3. HDMI-RCA. Be prepared for the fact that the image quality will decrease significantly, even though the signal from the DVD player is output via HDMI.

Connection process and setup

Select the appropriate wire. Having specified which connector you will use, select the required cord and make sure that it is not torn or frayed. For clarity, the use will be described HDMI cable, as it is easier to connect and guarantees signal transmission highest quality. Sequence of actions:

1. Place the DVD player close to your screen so that the wire reaches the connectors on the TV.
2. Do not install electrical equipment on top of each other - it gets hot, which can cause it to malfunction.
3. Before connecting the cable, unplug the DVD player and TV. This will prevent the possibility of electric shock and protect the equipment.
4. Connect one end of the cable to the HDMI connector on your DVD player. Look for the “HDMI” or “HDMI OUT” markings.
5. Connect the second end of the cable to the HDMI connector on your TV. This connector is only available in . There may be several such connectors. Look for the “HDMI” or “HDMI IN” label with the appropriate connector number.
6. There are many different HDMI cables, but if you don't need a perfect picture, any wire that can reach your TV will do.
7. Turn on the DVD player and TV. Insert a CD to check the display and sound quality.
8. Switch the TV to receive the signal from the appropriate jack. To do this, use the “Source” or “Input” button on the TV or remote control. The connector you select must match the connector to which you connected the wire.

Conclusion

Knowing how to connect a DVD to a TV will make this process easy for you. The most important thing is to determine the required cord and adapters, everything else is not a problem. Good luck watching your favorite movies.

Appearance digital television caused a kind of excitement, since the content in digital quality became available to a wide range of users. IN lately it is this direction of television that is developing very actively, large number offices that will provide services for connecting and setting up digital television for a fee. The good news is that you can set up digital television on your TV yourself.

So in this article we will look in detail at all aspects of setup, both in general and for TVs from specific manufacturers. It is worth noting that there are various types digital television. All proposed schemes relate to cable “digital”.

General instructions

First let's look at general scheme digital television reception settings. IN various models TVs, the sequence of operations and item names may differ slightly. Don’t worry, next we will look at the configuration features for specific brands, all points will be illustrated.

1. Using the remote control, enter the menu of your TV. In the window that appears, select the “Options” item. In order to go directly to the configuration, you must select the “Auto Configuration” item. A window should appear on the screen asking you to select one of the signal sources: cable or antenna. Select the first option, and then click the “Start” button.

2. After the operations have been completed, a window should appear in which you must select “Digital” as the signal source and then press the “Start” button again.

3. We are at the final stage of setting up digital television. In the window that appears, we find the “Search Mode” item, several options will appear, we need the “Full” item. Click and fill in all fields with the data indicated below.

Frequency (kHz) - 314,000 (314 MHz).

Modulation - 256 QAM.

Transfer speed - 6875 kS/s.

Please note that some TV models support network search. This means that you do not need to manually specify the above parameters. Simply, after selecting the desired search mode, press the “Search” button. As you can see, setting up digital television on your TV is quite simple. For those who are confused, read the illustrated instructions below.

LG

It is logical to assume that different TV models from the manufacturer LG use their own firmware and menu. However, in general, the menu of all TVs has characteristic similarities. Find it on your remote remote control“Menu” button, press it and a window appears on the screen in which you need to select the “Options” item.

In the “Options” tab you will see several parameters available for change. In the “Country” item you must indicate either Germany or Finland.

After this, you need to go to the “Settings” menu, there select the “Auto search” item in which you specify “Cable” as the connection method.

After the completed manipulations, a window should open in which you need to select the “Settings” item and specify all the values ​​as in the figure below.

If you followed all the instructions correctly, then after searching, the TV will detect all available channels, as well as radio stations.

Please note that LG TVs use an automatic channel update function, which resets the existing channel list at certain intervals and starts a new search. For convenience, it is advisable to disable this feature. To do this, go to the “Settings” tab digital cable» and turn off automatic updates. Thus, setting up digital television on LG TVs is quite simple. All it takes is a little care.

Setting up digital television on TVs Philips

So, find the “Menu” button on the remote control and use it to go to the menu of your TV. Next, you need to go to the “Configuration” section.

In the window that appears, click on the “Install” item, after which a secondary menu will appear on the TV screen, in which you need to select the “Channel setup” section. Another submenu will appear, in which we select the “Automatic” item. Settings". If you have completed all the transitions correctly, a message should appear warning you about the upcoming update of the list of all channels. Click “Start”.

Go to the section"Country" and select either Finland or Germany from the list.

For connection method, select"Cable".

Before you start the channel search process, go to the “Settings” item and make the settings according to the images below.

Now you have managed to set up digital television on your Philips TV. You can start directly searching for channels; to do this, click “Start”.

Setting up digital television on TVs Samsung

On the remote control, press the “Menu” button. Your TV menu should appear on the screen. Go to the “Channel” section (shown as a satellite dish). Several tabs will appear on the right, select “Antenna” and select “Cable” as the connection type. Next, you need to go to the “Country” tab and specify the “Other” parameter. In this case, the TV should request a pin code. If you did not change it yourself, then enter 0000 (default value).

Go to the “Auto Configuration” tab and select “Cable” as the signal source.

Set all parameters as in the image below, then click “Search”.

After all operations, your TV will detect all available channels.

Setting up digital television on TVs Toshiba

Using the “Menu” button, go to the TV menu and select the Russian menu language.

Find the "DTV Manual Tuning" tab.

Manually enter all the parameters as in the image below.

After that, click “Ok”, the search for channels will begin.

Conclusions

We have discussed in detail the diagram of how to properly set up digital television on your TV. We supported all sequences with images for better perception. If you have any questions, please use the form feedback our website or ask a question in the comments.

with DVB-T2 support and media player function

"Find golden mean Can.
But she is always required to make an adjustment to the left or right.
At least for a little bit."
Dmitry Kalinin

Transition from analog television broadcasting to be accepted as a federal standard in the territory Russian Federation digital DVB-T2 influenced not only the computer TV tuner industry. A fleet of TVs either without digital support broadcasting, or with support for the first version, DVB-T turned out to be more than impressive, while many models simply did not have time to become obsolete in terms of diagonals and resolutions. A solution was found quite quickly, they became stand-alone TV tuners (in the future we will use the established term “receivers”), connected to TVs, usually via HDMI or a composite interface, less often supporting SCART (optional with RGB), while the retail price of such devices allows us to consider them accessible even in modern conditions of the domestic market.

The company was among the first manufacturers to introduce similar solutions, one of which with the heavy name BBK SMP137HDT2, based on the current chipset, we will consider further in the text.

Scope of delivery

The compact box has the traditional BBK white and blue color scheme, explanatory notes are localized.

In addition to the receiver itself, the kit includes:

• remote control;
• 3 RCA - 3 RCA composite cable for analog video and audio connection;
• user manual.

Design and specifications

The manufacturer claims the following features of the BBK SMP137HDT2:

• DVB-T/DVB-T2 support;
• frequency range - 174-230 MHz (VHF), 470-862 MHz (UHF);
• rated power consumption - 8 W;
• level input signal- −75 - 20 dB mW;
• video decoder - MPEG-1, MPEG-2, MPEG-4 HD, H.264;
• audio decoder - MPEG-1, MPEG-2 (Layer I/II), MP3, AC-3, AAC-LC, HE-AAC;
• input stream - up to 40 Mbit/s;
• image format - 4:3/16:9;
• audio formats - MPEG Layer I&II, 32/44.1/48 kHz;
• electronic schedule of EPG channels;
• delayed viewing mode TimeShift;
• video recording function (PVR);
• JPEG support;
• USB 2.0 port for connecting external USB-compatible devices;
• support for MKV (Matroska) and TS containers;
• Dolby Digital support.

The device is available in two colors - black (Black) and dark gray ( Dark Gray), the second option was tested. BBK SMP137HDT2 is a compact (device dimensions 174×158×42 mm, weight 370 g) parallelepiped with rounded corners. On the front panel, in addition to the name and several logos, there is a two-color color (red in standby mode, green during operation) LED indicator and a USB port.

The rear panel contains an IEC antenna connector, an HDMI connector, and three RCA connectors for composite video and stereo audio.

The receiver has a built-in power supply; the cable cannot be disconnected.

On the bottom you can see ventilation holes and 4 legs, 2 plastic and 2 rubber.

The sticker informs you about the version number 2.0.

Alas, the retail origin of the test copy did not allow us to take a photo printed circuit board, so we will limit ourselves to listing the microcircuits used.

The basis of the BBK SMP137HDT2 is a single-chip system (system-on-a-chip, SoC) ALi M3821, produced in the summer of 2014. According to the manufacturer, combining the M3821 with the company's MxL603 RF unit provides high level protection against interference caused by 4G/LTE, Wi-Fi and FM signals. This combination is complemented by a DDR3-800 memory module with a capacity of 64 MB.

The receiver was tested with Samsung TV LE40B530P7W, AVerMedia Live Gamer HD card was used for capture.

Remote control

BBK SMP137HDT2 is equipped with a 43-button remote control labeled RC-SMP712.

The remote control lies quite comfortably in the hand, but the size of many buttons could be increased and the response made more informative.

List of broadcast channels during testing

Digital broadcasting in Samara is carried out at a frequency of 522 MHz with M-PLP technology (Multiple Physical Layer Pipes - several channels physical level), allowing different schemes modulation and different levels of error tolerance for different streams in a multiplexed DVB-T2 signal.

Connection

Connecting devices of this class is extremely simple, except for the antenna in the case of a TV with HDMI input An appropriate cable is sufficient, however, due to the absence of one in the package, it is better for the potential user to look for a cable in advance.

Composite video output and analog audio outputs work simultaneously with HDMI, video modes with 24, 25 and 50 frames per second in the settings correspond to the PAL standard, with 30 and 60 frames per second - to the NTSC standard.

Settings

The user interface of the BBK SMP137HDT2 has its own name InErgo.

As it turns out, such a pretentious name hides the usual hierarchical menu of basic settings.

Subsection “Menu language” section system settings contains not only a setting of the same name, but also a teletext setting and a choice of priorities when there are several audio tracks in a stream.

In the image settings there are two subsections: “Video output”, in which the resolution and frequency are selected (1080i_25, 1080i_30, 1080p_50, 1080p_60, 1080p_25, 1080p_30, 1080p_24, “original”, “on TV info”, 480i, 480p, , 576p, 720p_50, 720p_60, default is 1080i_25), and “Aspect Ratio” (Auto, 4:3 PanScan, 4:3 Letterbox, 16:9 Normal).

The “Auto” mode failed to determine the aspect ratio under test conditions, and best results, oddly enough, demonstrated the 4:3 Letterbox mode.

In the digital audio output settings, you can select LPCM or BS Out; the receiver supports bitstream when connected via HDMI, which allows you to use the device as a media player with an external decoder.

BBK SMP137HDT2 does not have external display to display the time, however, correct installation may be required to use the scheduler. The DVB-T2 standard supports time transmission, but the user can select a region, time zone, or manually configure it if the “Set GMT” option is disabled.

Screen settings allow you to adjust brightness, contrast, saturation, hue, and clarity.

Supported parental controls(you can set the minimum age to 10, 12, 14, 16 and 18 years old, the restriction also applies to recorded programs), there is a firmware update option via USB (at the time of testing no updates were found on the manufacturer’s website), information about the firmware of our copy is presented below.

The “Other” subsection includes settings additional food antennas, channel displays and automatic switching on standby mode.

The BBK SMP137HDT2 interface provides ample opportunities for setting up channels.

In addition to automatic search on the OIRT frequency grid (178 - 226 MHz, channels 6 - 12 and 470 - 860 MHz, channels 21 - 69), channel search with range selection and frequency search with manual input and bandwidth selection are available (6, 7 and 8 MHz).

Signal level and quality percentage values ​​are displayed immediately after entering the frequency.

Automatic search allows you to skip encrypted channels if available.

Channels can be sorted by uniquely assigned numbers (LCN) and Service ID in the order they are transmitted in the stream. In addition, sorting can be disabled.

The list of channels can be edited (contextual operations are carried out using colored buttons on the remote control), sorting by name in forward and reverse order, displaying open/encrypted, blocking,

renaming

and moving in the list.

BBK SMP137HDT2 supports Electronic Program Guide (EPG).

The 8-position timer, which can be configured from the EPG window, supports both recording and viewing; during testing, the device was brought out of standby mode and went into standby mode upon completion of the active task without any complaints.

Teletext is processed correctly.

To record programs and use the delayed viewing mode, Timeshift requires a connection to the port. USB drive. The manufacturer recommends a volume from 4 to 500 GB and file system FAT32, however use during HDD testing 750 GB with NTFS had no effect on operation in these modes.

A folder ALIDVRS2 is created on the connected drive; for each recorded fragment a own folder with the date in the name, the recording is carried out in TS format, and two service files with *.dvr extensions are created.

During direct recording (Record button on the remote control), pressing the button again allows you to set the recording time. Ending recording with the stop button requires confirmation, which eliminates accidental interruption; at active mode Delayed viewing is recorded from the moment it is turned on.

Recorded fragments can be renamed, locked with a password, and deleted.

The built-in media player is capable of displaying recorded files, video files, sound files and image files.

Files supported are AVI/*.avi, MKV/*.mkv, MPG/*.mpg, *.ts, *.m2ts, MP3/*.mp3, Vorbis OGG/*.ogg, H.264 MP and HP @L4 video codecs .1, MPEG-1,2,4 SP ASP @L5, audio codecs MP2, MP3 (up to 320 kbps), AC3, ADPCM, AAC, HEAAC, OGG (up to 192 kbps). The maximum resolution and bitrate are 1920×1080 and 20 Mbit/s, respectively. Despite the lack of FLAC support in the official specifications, such files are also played.

Support for Dolby Digital and bitstream increases the functionality of the device as a media player; during testing, the receiver coped with all files within the stated specifications.

Devices of this class do not have absolutely correct support for playback of 24p video materials (23,976 and 24 frames/s), however, the negative effect can be minimized to a comfortable level by selecting the video mode.

Quality

The image quality when working with DVB-T and DVB-T2 is determined by the operator in the range from low resolutions with low bitrates to HDTV. DVB-T2 channels are currently only available in standard definition.

The time from turning on the device until the image appears is about 15 seconds.

The receiver provides good quality reception of digital channels, switching between channels takes about 2 seconds, between channels in different PLPs - about 3 seconds.

Conclusions

Pros

• correct work with M-PLP;
• good reception quality;
• compactness;
• TimeShift delayed viewing mode (if there is a connected drive);
• support energy saving mode for scheduled tasks;
• Dolby Digital support.

Cons

• lack of display;
• lack of opportunity pass-through connection antennas;
• large diameter LED indicator;
• The remote control is not very convenient.

BBK SMP137HDT2 is a typical representative of modern DVB-T/DVB-T2 receivers and is produced by a fairly well-known brand. The device does not stand out in anything special, but it copes with its functions, has no significant drawbacks, and its availability in retail sales, the manufacturer’s reputation and the availability of authorized services can tip the scales in favor of this model.

So that you can watch on an analog TV digital channels broadcasting requires special equipment called a receiver, tuner or set-top box. BBK Electronics company in the region digital equipment succeeded. The market offers BBK TV set-top boxes of decent quality and functionality. BBK receivers not only accept DVBT2 signals, but can also record selected programs into memory for later viewing.

The main feature digital tv set-top box consists in the absence of the need, as for satellite TV, to worry about installing a bulky antenna or laying a cable. For this device to work, it is enough small indoor antenna and connecting the BBK set-top box to the TV.

While the number of available channels is significantly smaller, it is limited to 20 terrestrial TV channels versus a couple of hundred channels for other solutions. But digital television broadcasting with the introduction of new multiplex equipment will eventually expand their number, HD and even 3D TV channels will appear.

BBK digital tuners are not inferior satellite receivers in functional terms:

• high image quality;
• ability to record program inclusion planning;
• pause and rewind.

User reviews of brand models in to a greater extent positive. Most often, a friendly, intuitive interface is noted. Users are satisfied fast switching channels, TV Guide (EPG) function), which prevents you from missing your favorite programs. The device’s ability to save videos and photos to small-capacity USB drives is noted, the quality playback in FullHD format.

Comparative analysis of popular BBK brand models

Given the variety of proposals, it is difficult to understand which model is better, so we present comparative analysis the most popular devices in the user environment.

The considered bibike consoles generally have similar functionality, the devices differs in some details:

• external design, number and placement of communication connectors;
• range of supported video and audio formats;
• data flow rate
• additional options.

Connecting and setting up a BBK TV set-top box

The method of connecting the device to the TV depends on the availability of the corresponding connectors on the TV receiver. Old TV can be connected via tulip cables through the component output of the set-top box (AV, CVBS). It is logical to connect a more modern TV receiver with an HDMI connector via HDMI cable through the corresponding port of the set-top box. If your TV does not have the connectors listed above, but there is a SCART port(in the form of a comb), you will need to purchase an adapter. The plug from the indoor or outdoor antenna must be inserted into the antenna socket of the set-top box.

Rf out port on TV box can be used to transport analog signals to a TV. To configure the BBK prefix, you need to perform the following steps.

1. Make sure that the set-top box is connected to the TV correctly.
2. Connect digital receiver to the power supply and turn on the BBK set-top box without a remote control (there is a power button on the case) or using a remote control (if there is no power button on the case).
3. When you turn on the receiver software for the first time, it will display a welcome window, prompt you to select the interface language, broadcast region, and define screen parameters.
4. Next, to initiate a channel search, click the “OK” button.
5. At the end of the search, the found channels are automatically saved.

If you need to reconfigure the device, go to the window initial setup possible after restoring factory settings. Path to the “Main Menu” mode → “Settings” → “Factory settings”.

The procedure for initial setup/reconfiguration of a digital tuner is described in more detail in the instructions for each specific model.

Ways to solve connection problems

During operation of digital electronics, malfunctions may occur. If the tuner does not respond to the remote control, the first thing you can try is to replace the batteries. If that doesn't work, the remote control may be faulty and will need to be replaced.

Crashes happen when The set-top box does not pick up channels. You can try the following solutions to solve the problem.

1. Reboot the device (turn off the power and turn it on again using the power button on the device itself).
2. Launch automatic search channels. This method may cause manual channel sorting to be reset. But arranging the channels in the right order is not difficult after solving the problem.
3. If the first two options did not give desired result, you can restore factory settings and reconfigure the device from scratch. The sequence of pressing the buttons should be looked at in the manual for the specific model of the console.

Advice! Before proceeding with the above steps, you should make sure that the receiver is not finding channels due to a software failure, and not due to problems at the local repeater.

3. Confirmation will be required, click “OK”.

4. After which the tuner will reset the settings to factory settings.

5. Press “EXIT” and the main menu will appear.

6. Enter the “System Setting” section in the main menu to change the menu language.

7. Select the “Language Setting” section and click “OK”.

8. The language setting menu will open.

9. Change “Menu Language”, “Subtitle Language” and “Audio Language” from “English” to “Russian” using the left and right buttons on the remote control.

11. Press the “Menu” button on the remote control, the main menu will open. Then enter the “Install” menu item.

12. Select “Search for channels” and press “OK”.

13. Select the “Search Mode” line and use the left or right buttons to set the value to “Manual” instead of “Network”.

14. Enter the following parameters:

• Frequency 322000 Khz (dialed using the remote control channel buttons).
• Flow rate 6750 KS/s (selected using the remote control channel buttons).
• QAM 64 type (selectable by pressing the right or left button).
• Turn on network search (selected by pressing the button to the right or left).

If the settings are correct, two indicators will appear in the lower right corner: “Signal Level” and “Quality”.

15. After the indicators appear, use the up or down buttons to move down to the bottom line “Start search” and press the “OK” button.

The receiver will automatically search for channels within 1-2 minutes.

16. A message will appear on the screen indicating the number of television and radio programs found. In order to save the programs, you must click the “OK” button.

After saving (channels), in order to exit, you must press the “EXIT” button on the remote control.

17. In the main menu, enter “Org. Channels".

18. By moving channels, arrange the channels in a sequence convenient for you.

1. Enter "Menu" and select "Factory Settings", click "OK".

2. Enter the password (the default should be 0000).

Then click OK.

4. Select your desired language.

5. The “Main Menu” will appear, select “Install” and click “OK”.

6. Select Manual Scan and click OK.

7. Enter the frequency: 322000 MHz (using the channel buttons on the remote control).
Flow rate: 6750 (selected using channel buttons on the remote control)
Modulation: 64 QAM (selectable with left and right buttons on the remote control)
Set “Network search” to “AVAILABLE” (selected with the left and right buttons on the remote control).

Once the parameters are entered correctly, a signal will appear.

Click “OK” and the tuner will find all channels and radio stations.

To save the channels, click “OK”.

8. Using channel editing, we arrange them in a sequence convenient for you.

1. Press the “MENU” button on the remote control. The main menu will open. Use the left and right buttons to select “Channel Tuning”. Select the “Delete all channels” section.

2. Confirmation will be required. Click "OK".

3. The tuner will delete all tuned channels.

4. Select “Installation” in the main menu (using the left and right buttons).

5. Go down to the “Manual Search” section (using the up and down buttons).

6. Click “OK”.

7. Enter the frequency (using the channel buttons on the remote control)

• Symbol rate (set by channel buttons on the remote control)
• Cable: (selected with the left and right buttons on the remote control)
• A signal should appear below.
• Click "OK".
• The tuner will find channels with the specified parameters.
• To save the channels, click “OK”.

To search for other channels, select the next transponder using the right button on the remote control. And enter other parameters for the next TV package.

8. After setting up all TV programs, go to the “Channel settings” in the main menu to move to a sequence convenient for you.

Highlight a channel using the OK button and move it to a position that suits you using the up and down buttons.

1. Press the "MENU" button on the receiver's remote control. The main receiver settings menu will appear on the TV screen.

1.1 By moving the keys up or down on the receiver remote control, you must select the menu line “SEARCH CHANNELS” and press the “OK” button.

2. Press the up or down buttons until we are in front of the “SEARCH PARAMETERS” item in the right column of the menu and press the “OK” button.

3.In the “SEARCH PARAMETERS” menu, enter the parameters one by one:

3.1 Frequency 322000 Khz (selected using the remote control channel buttons).

3.2 Flow rate 6750 KS/s (selected using the remote control channel buttons).

3.3 QAM 64 type (selected by pressing the right or left button).

3.4 After entering the parameters, press the “OK” button and go to the previous menu.

4.Press the up or down buttons until in the right column of the menu we are opposite the line “AUTO SEARCH” and press the “OK” button

4.1 Confirm the action by additionally clicking the “OK” button.

5. Wait for the channel search to finish

1. Press the "MENU" button on the receiver's remote control. The main receiver settings menu will appear on the TV screen.

By moving the keys up or down on the receiver remote control, you must select the “INSTALLATION” menu line and press the “OK” button.

2. The INSTALLATION menu will open. By moving the keys up or down, you must select the “Factory settings” menu line and press the “OK” button.

3. After which the tuner will reset the settings to factory settings.

4. Enter the main menu.

5. Select Install and click OK.

6. Select "Search for channels" and press "OK".

7. The “SEARCH CHANNELS” menu will open.

7.1 Select the line “SEARCH MODE” using the up and down buttons.

7.2 Press the buttons to the right or left until the inscription Manual appears in the right column of the menu opposite the line “SEARCH MODE”.
At the same time, the following lines will have to become active (it will be possible to change parameters): 2-Frequency, 3-flow rate, 4-QAM type, 5- Network search.

7.3 Enter the parameters one by one:

7.4 Frequency 322000 Khz (selected using the remote control channel buttons).

7.5 Flow rate 6750 KS/s (selected using the remote control channel buttons).

7.6 QAM 64 type (selected by pressing the right or left button).

7.7 Turn on network search (selected by pressing the right or left button).

7.8 If the settings are correct, two indicators will appear in the lower right corner: “Signal level” and “Quality”.

7.9 After the indicators appear, use the up or down buttons to move down to the bottom line “Start search” and press the “OK” button.

8. The receiver will automatically search for channels within 1-2 minutes.

9. A message will appear on the screen indicating the number of television and radio programs found. In order to save the programs, you must click OK.

After saving (channels), in order to exit, you must press the “EXIT” button on the remote control.

10. In the main menu, enter “org. Channels".

11. By moving channels, arrange the channels in a sequence convenient for you.

1. Press the "MENU" button on the receiver's remote control.

2. The main receiver settings menu will appear on the TV screen. Select the item “Search for channels”

3. In the window that appears, select “Quick search”.

4. Enter the following parameters:
◦ Start frequency 346.0 MHz
◦ Transfer rate 6750 kS/s
◦ Search QAM 128-QAM
◦ Network Search Yes
Then select “Search”, the process of searching for channels will begin.

5. When finished, click “OK” in the window that appears and exit the menu with the “EXIT” key

4.In the main menu you need to go to the “Timer” item to set the time

5.Configuring CATV.Go to CHANNEL.

6.Broadcast type, select CABLE TV.

7.Select the search option “DVBC manual search”, and set the following parameters:

Modulation: 64 (QAM) (QAM type)

• Your TV is set up.

1. Photo of the TV remote control on which the settings will be made.

2.To enter the TV menu, you must press the MENU key on the remote control. Depending on the model, the menu interface may differ, but general meaning and the procedure remains relevant. To do this, go to the SETTINGS item (confirm the selection with the “OK” key on the remote control)

3. Go to the CHANNEL section. Specify the antenna type DVB-C. Go to the Automatic tuning section

4. Scan type Manual DTV setup. Set the following parameters:

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

• Click SEARCH

6.Your TV is configured. By pressing the “EPG” key, a menu will open, electronic program transmission

1. Photo of the TV remote control on which the settings will be made.

2.To enter the TV menu, you need to press the MENU key on the remote control. Depending on the model, the menu interface may differ, but the general meaning and procedure remains relevant. To do this, go to the SETTINGS item (confirm the selection with the “OK” key on remote control)

3.Before you start setting up channels, you need to change the language version of the TV menu (if necessary). To change the language, you need to go to the “Settings” item. (to do this, you need to select this item and confirm the action with the “OK” key on the remote control).

4.To set up TV channels, you need to enter the CHANNELS section.Then select manual setting TV.

5.You need to select DVС TYPE and set the following network parameters:

• Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Your TV is set up.

1. Photo of the TV remote control on which the settings will be made.

2.To enter the TV menu, you need to press the MENU key on the remote control. Depending on the model, the menu interface may differ, but the general meaning and procedure remains relevant. To do this, go to the SETTINGS item (confirm the selection with the “OK” key on remote control)

3.Before you start setting up channels, you need to change the language version of the TV menu (if necessary). To change the language, you need to go to the “SETUP” item. (to do this, you need to select this item and confirm the action with the “OK” key on the remote control).

4.To set the time, you need to go to the TIME SETTING item.

5.To configure channels, you need to go to the CHANNEL section and select Manual search

6.Select:

• Country Russia.
• DTV+ATV mode

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

1. Photo of the TV remote control on which the settings will be made.

2.Enter the settings menu by pressing the button on the remote control

3. By pressing the “up” and “down” keys, go to the “Channels” section. The connection to TV should be indicated as Cable. If you have an Antenna, try pressing the “Source” key on the remote control and select DTV or DVB-C. If, when you select this item, there is no cable in the options, or the TV does not prompt you to select a signal source at all, your TV may not have a tuner DVB-C standard

4. Select the “Manual tuning of digital channels” section using the “up” and “down” keys, and confirm the selection with the “OK” key. Next, select the “Digital” option.
5.Next you need to specify the search parameters Search type:

• Network search

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Click "Start"

7.The TV will ask you to confirm the search, select “OK”. Auto search has started.

1. Photo of the TV remote control on which the settings will be made.

2.To enter the TV menu, you need to press the MENU key on the remote control. Depending on the model, the menu interface may differ, but the general meaning and procedure remains relevant. To do this, go to the SETTINGS item (confirm the selection with the “OK” key on remote control)

3.Before you start setting up channels, you need to change the language version of the TV menu (if necessary). To change the language, you need to go to the “LANGUAGE” item. (to do this, you need to select this item and confirm the action with the “OK” key on the remote control).

4. Menu language must be specified as “Russian”. Preferred audio language must be specified as “Russian”. Preferred audio language 2 must be specified as “English or Russian”. Then press the “MENU” key to go back.

5.In the main menu you need to go to the “Timer” item to set the time

6.Go to the clock item.

7.In the menu that opens, specify the time and date.Then press the “MENU” key to go back.

8.You need to go to the Settings menu

9.In the setup menu:

The country should be “Russia”;

Tuner mode “Cable TV”;

Go to Channels (by pressing the “OK” key on the remote control)

10.In the Channels menu (go to Manual cable TV setup by pressing the “OK” key on the remote control)

11.In the search menu you need to specify the Country “Russia”

13.Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Go to the Search item and press the “OK” key on the remote control.

You need to wait until the TV setup is completed.

14.Pressing the “Guide” key will open the menu of the electronic program guide.

1. Photo of the TV remote control on which the settings will be made.

2. Select a language. Using the remote control (hereinafter referred to as the RC), use the ˂/˃/ ˄ / ˅ arrow buttons to select the “Russian” language. Press the center button to go to the next page.

3. Select a country. Using the remote control using the ˂/˃/ ˄ / ˅ arrow buttons, select the country “Russia”. Press the center button or the right arrow ˃ to go to the next page.

4. Select a location. Using the remote control, use the ˂/˃/ ˄ / ˅ arrow buttons to select the “Home” location. Press the center button or the right ˃ arrow to go to the next page.

5. Start setting up. The screen will display the message “Start Auto Setup?” Press SKIP, then select manual setup options

6. Select the connection type. Using the remote control using the ˄ / ˅ arrow buttons, select the TV connection type “Cable”. Press the center button or the right arrow˃ to go to the next page.

7. Setting up CATV.

Using the remote control, use the ˂/˃/ ˄ / ˅ arrow buttons to select the following values:

Scan Type → Full Scan

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Using the remote control, go to the “Start” button, then press the center button or the right arrow ˃ to go to the next page.

9.Watching KTV.

Digital TV is set up!

To view the channel list, press the “home” button and use the ˂/˃/ ˄ / ˅ arrow buttons to select the “Digital TV” tab.

Next to the TV channel number you can see its name and the program running at that moment.

If your TV model provides for the reception of digital channels, but does not have the “DTV MENU” item, then first select another country - France, Switzerland, Sweden or Finland.

1. Press the button - "DTV"
2. click - "DTV MENU"
3. select - "Installation"
4. select - “Manual tuning” Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)
5. click - "OK"
Setup takes approximately 5-10 minutes.

Since not all SONY models are equipped digital tuner for cable TV (DVB-C) You need to check the model of your SONY TV.
Models equipped DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-32EX402R2 the first 3 letters in the model name (KDL) indicate that the TV is “digital”. In models KLV-**BX***, etc. DVB tuners No.

1. Press the "MENU" button (for some models it is called "HOME" on the remote control (hereinafter referred to as the remote control). This button is usually blue.
2. Select the “Settings” item.
3. Find the “Digital Configuration” menu in the list of settings and enter it
4. Select "Auto search for digital stations"
5. A source selection window will open - select the TV connection type. Select "cable"
6. In the selection of scan type - select the "full scan" mode
6.1 Or select "Manual"
6.2 Next, enter the Frequency: 322,000 (KHz) (322 MHz)

Modulation: 64 (QAM) (QAM type)
6.3 Leave the access code “Auto”. Next, enter the symbolic rate 6750

7. Click "start"
Wait until the TV finishes searching for channels.

Pay attention to the bottom of your TV's OSD menu. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.

1. Turn off the TV and install the conditional access module. Turn on the TV. Go to the menu. Select the language Russian.

2.Go to the DTV manual setup tab and click OK

3.Enter frequency 322,000 KHz, modulation 64, symbol rate 6750

4.After pressing the OK button, a search will begin, as a result of which the channels should be found.

2.Indicate the country Finland or Germany

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Auto Channel Update: Off

1. In order to set up digital TV channels for the vast majority of Samsung models, press the “Menu” button on the remote control, the TV menu will open in which you will need to select the “Channel” section (Satellite dish icon). In the “Antenna” tab, specify the connection type “Cable”. Go to the “Country” tab and select the “Other” option. The TV will ask for a pin code, if you have not changed it, you will see 0000

2. Go to “Auto-tune” Signal source: Cable, Choose the type of channels at your discretion, you can find only digital channels, or digital + analog

3. Specify Search Mode: Quick, Network: Auto, Ident. Networks:-----------, Frequency: 322 000 (KHz) (322 MHz) Bitrate: 6750 (KS/s) (bit rate, symbol rate) Modulation: 64 (QAM) (QAM type)

4.As a result of the search, you should find channels

1.In order to set up high-definition digital TV channels for the vast majority of Philips models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Configuration” section

2.Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list, click “Start”

3.Select "Reinstall Channels"

4.In the Country section, you must select Finland, but if this country is not in the proposed list, then select Germany

5.Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”

6.Before you start searching for channels, select “Settings” to manually correct the search parameters

7.Install manual mode transmission speed. In the tab, change the transmission speed manually from the control panel to the desired one. In some TV models, the flow rate is indicated in the “Character 1” tab 6750 “Character 2” is left at 0.

8.Now set the network frequency to manual mode and enter the network frequency 322.00 from the control panel

9.After clicking the done tab, you will again be taken to the channel launch menu, now you can start scanning

10.If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.

1.In order to set up high-definition digital TV channels for the vast majority of LG models, press the “Menu” button on the remote control, the TV menu will open in which you will need to select the “Options” section

3.Now go to the “Settings” menu, “Auto search” item and specify the method of connecting to the TV “Cable”

4.Now in the window that opens, go to “Settings” and enter the following parameters:

Search type:fast, Frequency: 322 000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type), Network ID: auto

5.If you did everything correctly and saved all the changed parameters, then during the search you will find channels and radio stations

6.An important feature of LG TVs is the “ Automatic update channels." It must be disabled, otherwise the TV will periodically reset the channel list you have configured.

Go to “digital cable settings”:

Auto Channel Update: Off

1.In order to set up high-definition digital TV channels for the vast majority of LG models, press the “Menu” button on the remote control, the TV menu will open in which you will need to select the “Options” section

3.Now go to the “Settings” menu, “Auto search” item and specify the method of connecting to the TV “Cable”
An important feature of LG TVs is the “Automatic channel update” function. It must be disabled, otherwise the TV will periodically reset the channel list you have configured. Auto Channel Update: Off

4.Now in the window that opens, go to “Settings” and enter the following parameters:

Search type:fast, Frequency: 322 000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type), Network ID: auto

5.If you did everything correctly and saved all the changed parameters, then during the search you will find channels and radio stations

3. Select the source “Cable TV”

4. Operator “Other operators”

5. Enter the following parameters: Use the left/right arrows to select the scanning type, name “Fast” Frequency 346000 kHz Symbol rate, Modulation, Network ID “Auto” Check the box for “Skip encrypted channels and press “OK”

6. Check the box for “Digital only” and click “Run”. The TV setup will begin. When finished, exit the menu. Your TV is set!

1. Press the “HOME” button on the TV remote control.

2. The main menu will appear on the TV screen. Select “Settings”

3. In the window that appears, select “Broadcast”.

4. Select “Auto-tuning options”

5. Select “Auto Configuration”

6. In the channel scanning menu, set the following parameters:

Antenna “Cable” Channel type “Digital” Operator selection “Other” Search mode “Network”

7. Start Scanning. Wait until the search is completed.

6. Enter the following parameters: Scan type Name Quick Chat settings Manual. Frequency 346 MHz Setting the network ID “Auto” Then select “Start”, the channel search process will begin.

7. When finished, click “Continue”, the setup is complete.

Press the "HOME" button on the TV remote control.

The main menu will appear on the TV screen. Depending on the version of the operating system, the menus and items may differ; below, as an example, two different menu options are shown. Option 1. Scroll down the menu and select the “Settings” → “Settings” section

Option 2: Scroll down the menu and select “Settings” → “System Settings”

In the window that appears, select “Channel settings”.

Select “Digital.” Configuration"

In the “Digital Configuration” section, select “Digital Setup”

In the next menu, select “Auto search for digital channels”

TV connection type “Cable TV Other”

Next, confirm searching for channels. Wait for the procedure to complete and exit the menu. Your TV is tuned!

3) Then you need to point the TV and receiver remote controls at each other and press the programmable button on the TV remote control once, in our case the TV power button. After this, the “SET” button indicator will blink twice and turn red.

4) To exit the programming mode, you need to press the “SET” button again, after which the indicator will turn off.

To program the remaining buttons, you need to perform the previous steps from points 1 to 4.

Topfield digital receivers

Digital receivers Signal

INTEK digital receivers