• Receiver gs 8306 latest firmware. Tricolor TV receiver firmware for free viewing

    • http://tech.servis23.ru/%D0%B7%D0%B0%D0 ... 5-gs-8306/ photo of the GS-8306 motherboard. The required chip is circled in red. The 200-470uF x 16V capacitor is soldered “plus” to the 2nd leg, “minus” to the 10th - marked with dots in the photo. Before soldering, the capacitor must be discharged.

    The numbering of microcircuit pins is always carried out counterclockwise starting from the key, this applies to both domestic and imported

    • Solder ceramic capacitor 0.1 µF for the power supply contacts of the microcircuit (legs 2 and 10). It is also advisable to duplicate the electrolytes of each voltage converter and the input power using ceramics. PS: On the underwater forum of the same name (submarine), the idea with a capacitor was criticized...
    • Solder the wire from the minus of the microcircuit (10 leg) to the body. The screws securing the board to the case do not provide grounding for the board. Grounding to the body is provided by the nuts of the tuner connectors. Effect from this method no - verified!!!

    Below are examples of resistance between the conductors in question.

    The resistance between the 2nd leg “plus” of the microcircuit and the 10th leg “minus” of the microcircuit is 362 Ohm

    Resistance between "plus"(2 leg chips)and tuner body


    The resistance between the negative (10th leg of the microcircuit) and the tuner body is 9 Ohms

    The resistance between the ground of the HDMI connector and the Tuner body is 9 Ohms (identical between the 10th leg “minus” of the microcircuit and the tuner body)

    2. Problem with sound loss

    • Replacement HDMI cable to a higher quality
    • Purchase anti-interference ferrite rings for the HDMI cable cm. . You can find it in radio stores or buy another HDMI cable with rings. In theory, the dependence on interference from other equipment connected to the power supply along with the receiver should disappear.
    • Grounding the receiver housing and the corresponding board. Solder the wire from tuner connector nuts to the HDMI connector housing)

    3. Preventing processor overheating on new firmware and, as a result, unstable operation of the receiver

    • Installing a heatsink on the processor and flash memory chip
    • chip datasheet here - .

    4. To ensure that channels do not disappear after turning off the receiver:

    1) you need to enter the receiver setup menu.
    2) reset the receiver settings to factory settings.
    3) after rebooting the receiver, the receiver setup menu will appear.
    4) select the operator " Tricolor TV".
    We go to the point " change antenna settings"Next select antenna No. 1 and point change, after that you get to the point antenna tuning, then change the frequency 10750 to 10751 in both windows (by numbers on the remote control) and press the save button, then press search for channels and scan them.
    To search federal channels with time shift +2 you must select a search region" Moscow +2" instead of " Moscow 0".

    PS When selecting regions "Basic" or "Ural" channel search will not be carried out.

    We update GS 8306 from USB to the new version 1.9.160, beginning

    GS 8306 has waited its turn and we are updating it via USB. For this we have new version software 1.9.160. Let's see what difficulties there may be during pouring. Because unfortunately updates on the operator's receivers lately don't go very smoothly.

    GS 8306 version p.o. 1.9.160

    GS 8306 update process

    2. The receiver begins the update process. The entire button is lit, but there is no image on the screen! It is impossible to check the update process on the screen; both receiver outputs do not work!

    GS 8306 version p.o. 1.9.160, upper diode.

    3. One diode of the receiver lights up constantly, the second blinks occasionally. This is all normal, the main thing is not to turn off the receiver from the network! If you turn off the power now, the receiver will fly far and long!

    GS 8306 version p.o. 1.9.160, the update process is complete.

    4. After the receiver has loaded everything, both diodes will go off! We wait at least 10 seconds. If you turn it off earlier, the receiver will be damaged! Of course, it’s scary, but that’s how everything is done here….

    GS8306 p.o. 1.9.160 inclusion.

    5. After everything has been updated, turn off the receiver from the network. We remove the flash drive from the USB. We turn on the receiver and configure all programs.

    GS8306 version p.o. 1.9.160 status check.

    That's all, we have updated our receiver, now we can watch television programs. The main thing to remember is that during the update our receiver may break and this is not a joke. The majority of users will not be able to repair the receiver themselves.

    If you still have doubts about how to update, watch the video. In this video, the entire update takes place in real time.

    Let's add another video about this firmware.

    On the website of the equipment manufacturer for Tricolor appeared The new software for the GS 8306 receiver is firmware version 1.9.160.

    This firmware was intended to replace software version 1.2.001, released several years ago. It must be said that firmware version 1.2.001 for the GS 8306 is exactly the software with which the GS 8306 receiver began to work more or less normally and stably - it did not freeze, the picture practically did not freeze, the channels switched quite quickly. With firmware 1.2.001, the GS 8306 receiver had only one problem left uncured - it could fail external unit power supply 12v, 2A, but the problem was solved by purchasing another unit at a price of 500-700 rubles. And even the above problem is not very common with the GS 8306 model.

    And now, after several years of successful operation of the receiver with proven and proven firmware, for some reason it was necessary to release new software - version 1.9.160.

    Well, they released a new firmware and released it. Usually, after updating the software, Tricolor receivers begin to work more stably. There was an expectation that even after updating the firmware to 1.9.160 everything would be fine.

    The website of the manufacturer of the GS 8306 model states the following: characteristic features new firmware (see screenshot below):

    Changes compared to previous version software:

    1. Modern graphical interface of Stingray software
    2. Improved receiver stability
    3. Added functionality for manual channel search
    4. Improved operation of the Tricolor TV Cinemas application

    Description of the characteristics of the new version of software for the GS 8306 receiver - version 1.9.160 Picture - screenshot of the page at - http://gs.ru/support/manuals-and-software/gs-8306/

    I would like to pay special attention to point No. 2 of the description of the new firmware - the stability of the receiver has been increased!!!

    In practice, we encountered the following problems when flashing and after flashing the GS 8306 receiver to version 1.9.160
    1. The receiver is flashed over the air, and if you confirm the completion of the firmware, it may not be successful - the firmware process freezes and the receiver remains in an unflashed state. At the same time, the old firmware has already been erased. That. the receiver turns into a brick. Further restoration is only possible by unsoldering the flash memory chip, flashing it in the programmer and soldering it back into the receiver. This is a relatively expensive procedure.
    2. Another problem with flashing is the long duration of its execution. People are starting to get confused about whether the firmware has already been completed or whether the procedure is still ongoing. Confused and unable to stand it, many of them, out of impatience, disconnect the receiver from the power supply and if the firmware has not yet been completed, then the receiver again turns into a brick.

    Those subscribers who were lucky and whose receiver, after several hours, was successfully updated to 1.9.160 will have to face other problems in the operation of the receiver, which previously worked stably.

    1. The message “no signal” appears periodically when viewing channels. After such a message, you can switch to another channel, watch it for a while, return to the channel on which the “no signal” message appeared and continue watching the selected channel again for a while. But only until the next time the “no signal” message appears.
    2. From the description of the new firmware it is clear that it has received a “modern graphical interface for the Stingray software.” So, the needs of this very Stingray, according to our subjective feelings, exceed the capabilities of the processor and memory of the GS 8306 receiver. This leads to the fact that channels now switch much longer than before - not with the old firmware 1.2.001.
    3. When switching channels, especially when switching channels of different thematic packages, some receivers simply reboot.
    4. Pink tint to the image after turning on the receiver. Some users actually encountered the problem that after the firmware all their channels are shown in pink color. Although, maybe it’s good to look at the picture in pink in our 21st century. The problem is eliminated by overloading the receiver's power supply.
    5. The picture may freeze terribly on some channels. On our test receiver, the “Match HD” channel, number 103 in the channel list, especially freezes.
    6. If after the firmware the receiver has not turned into a brick and continues to function at the very least, then sew it through USB port back to stable firmware 1.2.001 will not work - it is blocked
    7. Periodically, the receiver reboots on its own even without any action, such as changing the channel
    8. The audio and video tracks are periodically out of sync
    9. From time to time the receiver simply freezes, especially when it experiences some kind of load, for example, when switching channels.

    These are, perhaps, the main points that owners of the GS 8306 receiver on the new firmware 1.9.160 will encounter. And in our, again, subjective opinion, most of the listed problems are related to the fact that the hardware power of the GS 8306 receiver is not enough to satisfy all the needs of the new Stingray software.

    In light of all the identified operational problems with the new firmware 1.9.160, one can only guess what increase in the stability of the receiver the software developer is talking about.

    Now let’s talk about how to continue using the receiver on firmware 1.9.160

    This is what we personally did with our own GS 8306 receiver to improve its stability. This is the method that was recommended by colleagues who encountered and dealt with the problems of firmware 1.9.160 before us - to increase the stability of the receiver with the received signal, it is necessary to set the frequency (lower and upper) of the local oscillator to 1 MHz higher than the standard value - 10751 MHz versus the standard 10750 MHz

    After the local oscillator frequency was set to 10751 MHz, the receiver stopped displaying the “no signal” message when viewing channels and began to work more stably when viewing and switching channels. It is already difficult to do anything more.

    What else do you need to know when operating the GS 8306 on firmware 1.9.160

    New firmware changed the operating mode of the receiver. Now the receiver automatically determines which video output the cable connecting to the TV is connected to. Depending on which video output the firmware detects the connection cable to that video output, it will send a video signal. In the case when 2 cables (HDMI and 3RCA) are connected to the receiver at once, confusion may arise and the receiver will not understand which video output to send the video signal to. Therefore, at one time we connect only one video cable to the receiver.

    One more point is light indication on the receiver. Previously, the top lit indicator meant activity HDMI output set-top boxes, then on firmware 1.9.160 the glow of only the top indicator means that the receiver is in standby mode and to start watching it must first be turned on. And after turning on, the receiver will automatically send a video signal to the detected video output.

    Download firmware 1.9.160 for GS 8306

    If you really need it, then the “wonderful” firmware for the GS 8306 receiver can be downloaded from the official website of the manufacturer of this receiver at http://gs.ru/support/manuals-and-software/gs-8306/

    P.S. — After lengthy problems with mastering the new firmware for the 8306 receiver, a number of questions arose:

    1. Why was it necessary to write new software for the receiver if the old one worked stably and with virtually no complaints?
    2. when will new software appear that will fix all the problems and bugs in version 1.9.160

    To enjoy watching TV in peace and not worry about possible problems, you should use only the most modern, the best equipment. But progress is developing at such a rapid pace that even recently acquired equipment almost immediately begins to lag behind existing requirements. Therefore, in order not to spend extra money on purchasing new devices, you should simply update the software of old ones in a timely manner. An excellent option for keeping receivers up to date is the Tricolor gs 8306 firmware. But you should remember that professionals must update the software, since any error can make the receiver inoperable.

    Any update has several important goals:

    1. removing existing errors and combating existing system failures;
    2. introduction of a more convenient, functional and friendly interface;
    3. connection additional options and services;
    4. reconfiguration of equipment for proper operation programs;
    5. keeping equipment up to date.

    Moreover, in 2019, the firmware is updated both at the request of the user and at the initiative of the television company.

    You can find out about the possibility of updating the receiver on the provider’s official website or from information message on the TV screen. Other sources of information are also possible, since you can learn about software improvements from news on various sites, conversations with friends, and recommendations from specialists.

    GS 7300 firmware for free viewing Tricolor

    For those who have already decided to reflash the receiver themselves for free viewing And quality reception signals, you should choose one of the currently existing options:

    • installing the program using a bootable flash card;
    • automatic update of the receiver.

    It should be remembered that, regardless of the option chosen, users are required to be careful and careful not to find themselves in an unpleasant situation.

    A suddenly interrupted update or incorrect, thoughtless actions will lead to equipment breakdown and loss of the right to warranty service. It will be almost impossible to fix the damage, and repair costs will be close to the cost of a new receiver.

    Gi hd mini firmware for Tricolor without card 2019

    To update the receiver software without a card and unnecessary worries. Should download suitable program. It can be found on many third-party sites that offer users various programs and drivers. If the program is already ready, all that remains is:

    1. format the flash card by installing a file card on it FAT system 32;
    2. transfer the program to it (it is not permissible to change the file name, it is necessary);
    3. insert the flash drive into the USB port;
    4. turn the receiver on and off;
    5. after switching on, the automatic update process will begin;
    6. you must wait for the process to complete;
    7. and carry out the setup, indicating the basic parameters for using the device
    8. reboot the receiver.

    This completes the procedure and you can start using the updated equipment.

    It should be noted that it is impossible to cancel the firmware, so you need to download the program with extreme caution, since the quality of the equipment depends on it.

    Firmware for GS 8306 Tricolor

    If searching for an update on third-party resources seems difficult, and you cannot get to the official firmware website created specifically for Tricolor, you should wait until the system decides to update itself. For this you will need:

    • disconnect the receiver from the network;
    • turn on the receiver again;
    • turn on information channel provider;
    • wait until the question about updating the software appears;
    • agree with the installation;
    • wait for the process to complete;
    • configure the equipment.

    Please note that it is unacceptable to turn off the device during installation, as this will lead to irreparable malfunctions. The result of an interrupted download will be the absence of any work program, which would allow the device to be used.

    Additionally, it should be noted that if there is no system message (about the start of the update) within 5 minutes after turning on, you should reset the settings to factory settings and repeat the process.

    How to flash a Tricolor card for free viewing

    Despite the simplicity of the process, it is better to entrust the firmware to professionals, so as not to find yourself in a situation where the desired freebie will result in unexpected additional costs. But, if you make a firm decision to update yourself, you need to pay attention to the correctness of the selected program, since different brands receivers requires the use of different drivers.

    Additionally, it should be mentioned that there is a third setup option that involves using a computer. But it requires purchase special cable, which allows you to connect a PC to the receiver, so it’s better not to overpay and immediately contact specialists who guarantee high-quality results.

    It is natural that the Tricolor TV company is trying in every possible way to improve its services, which is why updates appear frequently. If you miss the release of new products and do not update your devices, then various difficulties associated with displaying channels and more are possible. You can avoid them with the help of technical updates of such popular models receivers like GS 8306 or GS 8307.

    How to update the receiver firmware

    Updating the GS 8307 or GS 8306 receiver software is a replacement old firmware on updated version, which meets the requirements of 2017. Updates from the past, 2016, are still relevant, but not for long. Please check the firmware version installed on your device; it may already be outdated at this point.

    For example, let's take the popular Tricolor TV GS receivers, namely GS 8307. The software version that must be installed on this device is 1.9.160. It was released in the last months of 2016, so it continues to operate this quarter. But there is every reason to expect that another new product will soon be released, which will have to be urgently installed in order to keep the receiver working.

    It is not recommended to ignore updates, although no one forces you to use them. It’s just that as soon as the program is updated, the receiver, in theory, should work better. But for inexperienced user It will be useful to know that when updating software, you should follow the following important rules:

    • At the moment when new software is being installed, you cannot turn off the set-top box, otherwise interrupting this process will cause serious damage;
    • The GS 8307 software should be updated in two stages. But human participation is exclusively accompanying, since the entire procedure takes place in automatic mode, and the most a person can do is press the remote control keys several times;
    • The time you need to spend updating the receiver is at least twenty minutes. But a lot depends on the model of the device and how correctly the procedure is carried out;
    • Whatever happens technical errors, and the receiver continued to work perfectly, you need to strictly follow the instructions, which will definitely be visible on the TV screen.


    Step-by-step procedure for updating Tricolor TV 8306

    In recent years, Tricolor television has been considered one of the most popular among analogues. But a significant disadvantage of this operator is the fact that it is necessary to frequently update the system. Of course, this point can only be called a minus with a big stretch, but, in truth, the need to constantly monitor updates so as not to lose your favorite channel suits few people.

    Instructions for updating the receiver firmware look like this:

    • You need to search for channels through manual control. To do this, find the corresponding item in the menu and click it;
    • When the previous step is completed, you need to unplug the power cable from the network so that the receiver turns off, and, after waiting a few seconds (up to a minute), turn it back on;
    • On the receiver, turn on the information channel under number “333”;
    • If the menu works as it should, a notification will appear on the screen saying that a new firmware version has appeared on the company’s website, and the user can update his device;
    • If you are interested in the offer, you can accept the update by pressing on the remote control remote control confirmation of actions;
    • The next step is to monitor the update process in the automatic window and perform simple manipulations that will help speed up the completion of the procedure;
    • At the end of the first stage there will be automatic reboot receiver, so there is no need to be scared - this is only a transitional stage for the next part of the updates;
    • When the second stage of the update is completed, a message will appear. Next, you need to set the parameters, language, date and time;
    • If everything is correct, you need to search for TV channels again, after which the 8306 Tricolor receiver will be almost ready for use.

    When all the necessary manipulations have been completed, the user needs to go to the “Setup Wizard” section to make sure that the software version has changed to a more modern one. The new firmware has a lot of nice bonuses, in particular, it is distinguished by a new graphical interface Stingray software, which, judging by the comments, was liked by many.

    Problems after flashing

    Unfortunately, even the best and most modern firmware is not a panacea for problems that can affect the receiver where it is installed. The software is still “raw” because it appeared not so long ago and the developers did not have time to remove errors. So it turns out that for some users everything works fine, while for others it’s the other way around.

    In the latter case, the problem can be solved. For example, by restarting the update again or using a flash drive rather than installing programs over the network. But if there are errors of a technical nature and they appeared after the firmware, then it is better to return to the old parameters until the Tricolor company corrects the errors that caused the trouble.

    If you go to old version firmware does not work due to technical points, then you need to go to service center, otherwise the equipment may be damaged. In principle, even after updating the receiver with low-quality firmware, you can correct the situation by waiting until a higher-quality sample comes out and flashing the device again. The errors are not too serious, so the wait will be minimally inconvenient.

    Read more: