Refilling ink cartridges for HP and Canon printers. How to refill an HP cartridge? Standard and safe method

It is necessary to start with the fact that when purchasing a new laser printer, as a rule, a “break-in” (trial) first cartridge is installed on it with a toner capacity three times less than in the standard one. Therefore, such a printer will be able to accurately print fewer pages than indicated in the instruction manual. Then the question arises, what to do next.

In any company store, after emptying the toner in the cartridge, you will be advised to install it on the printer new cartridge, otherwise you will lose the original warranty on your equipment. It should be noted here that laser printers are quite expensive equipment, and prices for new cartridges range from a third to half the cost of your laser printer. It follows from this that replacing a used cartridge with a new one will not be a cheap pleasure. Some manufacturers may offer their services for refilling them, while the right to warranty company service remains with the buyer. This can be found out in service center manufacturer of your equipment. If this is not possible, the cartridge must be taken to a specialist for refilling.

As a rule, the first three or four cartridge refills, if done correctly, will not affect print quality. Well, then on the printed pages you will see streaks of toner or unprinted areas. In this case, it is necessary to regenerate or restore the cartridge. And then it can be refilled again until the next regeneration. These procedures will cost you five times less than buying a new cartridge.

Most best way Save money by refilling the cartridge yourself. It will cost you three times less than turning to specialists, and six to eight times less than buying a new one. If you've never done this before, don't worry. The Internet can always help you. In it you will find almost all the instructions for assembly and disassembly, as well as for the process of refilling toner cartridges for almost all models existing printers. In addition, you can consult a familiar specialist.

The only thing that needs to be taken into account when refilling the cartridge yourself is the loss of print quality (for some models it may be insignificant). For printing texts, print quality does not play a special role. It's a completely different matter if you are engaged in professional printing activities. Referring to qualified specialists to refill cartridges or even replacing them with new ones in in this case are inevitable.

If you purchase a new one laser printer and plan to refill the cartridge yourself, you need to know that some cartridges for laser printers can be chipped by their manufacturers, that is, they cannot be refilled further (for example, samsung printer CLP-310). A special chip is installed in such cartridges, which turns them off after printing a certain number of pages.

Hello!

So, you decided to buy new printer(scanner, copier, etc.). On at the moment The office equipment market is quite large and the variety of models dazzles your eyes. A huge number of companies produce printers, copiers, scanners, plotters, multifunctional devices, shredders and so on, so on... All these devices have a bunch of characteristics, the variety of which is also quite difficult to understand. Inkjet printers, laser, is it possible for it? refill the cartridge, sizes, price, printing speed... In this article we will try to help you narrow your search and choose a quality device.

Choosing a manufacturer

First of all, let's look at choosing an office equipment manufacturer. At the moment, we can list quite a few well-known manufacturing companies that are more or less successfully engaged in the sale of office equipment. Among the most famous: HP (Hewlett Packard), Canon, Xerox, Samsung, Brother, Ricoh, Lexmark, Oki, MB, Sharp, Kyocera, Konica, Epson. What to choose? Everything is quite simple here. There are many companies, but only two occupy leading positions. This Hewlett Packard And Canon. The office equipment produced by these companies is very popular - several orders of magnitude higher than the office equipment of all other manufacturers. We recommend these two companies based on two fairly simple considerations. Firstly, it is very easy to find consumables for the devices manufactured by these companies. Secondly, refilling cartridges for these devices will not be difficult. Repairing an HP or Canon device is very easy. There are a lot of such devices in Moscow. Engineers have met with them more often, and therefore know better. Any spare part, down to the smallest screw, can be quickly found from any supplier. When refilling cartridges, you do not need to change any chips.

We sorted it out with the manufacturer - without much hesitation, we buy Canon or HP.

Inkjet or laser?

Today there are two types of printers. These are devices that print with ink (inkjet) and devices that use toner for printing (laser). Let's figure out what fundamental difference one type from another. We will not touch on the technical process and will talk about the differences that influence the choice when buying a new device.

Inkjet devices are quite cheap, unlike laser devices, which cost several orders of magnitude more. This is where the list of advantages of inkjet printers ends. Inkjet printers are difficult to repair. Two reasons: firstly, the high cost of spare parts compared to the cost of a new device, and secondly, the high complexity of repairs due to the ink supply system. Plus, it can be quite difficult to find spare parts.

The second significant disadvantage of ink-printing machines is the high cost of the copy. Let’s be clear: the cartridge is expensive, but it doesn’t last long. On average, for a regular, “home” inkjet printer, the cost of a copy is about six rubles for a black and white print of text (for example, a page of a book), and about fifty rubles for a color photograph in A4 format. Agree, quite expensive.

The third drawback: for inkjet devices it will not be possible to refill the cartridge. More precisely, it will be possible to refuel, but many problems will arise. Firstly, few people run them. Mainly refueling ink cartridges engage in radio markets (such as, for example, the Savelovsky radio market). Large companies Those involved in the field avoid inkjet devices, as it is simply unprofitable. Secondly, refilling ink cartridges is quite unstable: depressurization during refilling leads to the risk of ink spilling into the device. Naturally, it is unlikely that it will be possible to repair it after this.

From all this it follows that buying an inkjet printer only makes sense if you are buying a printer for your home and you need to print color images. Not everyone can afford to have a color laser printer at home: they are very expensive. That's why we have to buy cheap inkjet ones. If your plans do not include printing color images, it is better to buy a monochrome (black and white) laser printer.

The cost of a copy is several times cheaper, since it is possible to refill the cartridge. With refilling laser devices, everything is much simpler: they refill perfectly, but the printer can be damaged by refilling only if the refiller has completely crooked hands. If you take a regular q2612a cartridge, printing a page with text will cost you about 30 kopecks (this is if you refill the cartridge) and about eighty kopecks if you buy new cartridges. Even in the second case, the price of a copy is not comparable to the price of an inkjet print copy.

A little about the characteristics

At this point, we have already decided that we will buy Canon or HP. We also decided whether it would be inkjet or laser. What now? Now all that remains is to choose something from the resulting list, and it is quite large. At this stage, we recommend that you have a clear idea of the purpose for which you are purchasing the printer. For example: if you are buying a device for a secretary who will only need to print documents, there is no point in buying a fancy MFP ( multifunctional device), it is better to buy a simple printer. Features to consider:

Device type (MFP, printer, copier, etc.)
Color or black and white
Maximum format (A0 - A6)
Paper tray size
Print speed
Cost of cartridges and their resource
Device Dimensions

Is it possible to refill the cartridge?

Another important aspect when choosing a new device is the availability of refill the cartridge. Everything is quite simple here. After you have chosen several models you like, call any refill company and ask if they can refill cartridges for the selected model. Here it is worth paying attention to the cost of refilling: some cartridges are more expensive to refill than others, since they require a special toner. The print quality is the same, but you will pay more only because the powder is of a different class. The second point that needs to be clarified is whether it is necessary to change the chip when refilling the cartridge. If you followed our advice and chose HP or Canon, you can forget about this issue, since the chips for cartridges from these manufacturers do not need to be changed when refilling. If the chip is present, it does not affect printing in any way. It will simply display a message about the end of the toner, but will not block the printer.

Which model should I buy?

You might be thinking, “why did you have to say so much? unnecessary words, when can you just recommend several models? Unfortunately, specific model We can’t give any advice, and here’s why. We refill cartridges and repair office equipment and mainly deal with relatively “old” devices. Let's say a year ago. We don’t receive new devices unless they bring them to refill a cartridge for them, so we have virtually no information on new models.

Let's summarize:

Clearly outline for yourself the purpose of purchasing the device
Manufacturer: Hewlett Packard or Canon
We buy an inkjet machine only for home printing of color images.
Let's find out if it's possible refill the cartridge and the cost of new cartridges.

That's probably all. I hope we didn't miss anything. If you have any questions, call us, we will be happy to answer you! We wish you a successful purchase!

All inkjet printers work on the principle of releasing ink through small holes called nozzles. When the raw material reaches its end, white stripes appear on the document, which indicates that high-quality printing. And at this moment there is a need to replenish the paint. There are two ways to do this: buy a new cartridge or a bottle of ink to refill the syringe yourself. But can all devices be topped up using the latter method? AND which printer can you refill yourself??

The simplest devices are Canon. They provide high resolution when printing, they use an average amount of ink, but have very expensive original cartridges. Naturally, if you constantly replenish raw materials for a long time, sooner or later you will exhaust the print head, and then you will have no choice but to buy a new cartridge.

You may ask why Canon? Firstly, the devices of this company have a very well-thought-out calibration system. One box is intended exclusively for black, the other for the three main colors: yellow, red and blue. But even in it, each shade has its own specific niche, and when used, they merge on paper, and not inside.

Secondly, removing cartridges from the tray is very simple, just like putting them back. Thirdly, the paint itself in bottles is inexpensive compared to similar products from other brands. Fourthly, you can print as much as you like without worrying about how much ink is left. And lastly, you will not overpay for the installation of original new cartridges, one of which is enough for a maximum of 150 pages of documentary text for 20 photos measuring 10 by 15.

Almost no one manages HP on their own. In most cases, this is due to the fact that the cartridges of these printers are located completely inconveniently, in addition, there are difficulties in getting them out, and then errors may also occur. Almost all HP brand devices have an uninterrupted ink supply system. Moreover, this technology is installed directly by the manufacturer, which guarantees reliability in use. Another disadvantage of self-priming is that there are six shades of primary colors, not including black. It's easy to make mistakes in the holes.

But there is one model that can be refilled manually. This is PhotoSmart B109. Refers to classic MFPs. According to reviews found on the Internet, over the years of service the device has proven a 100% guarantee of high-quality printing when manually filling ink with a syringe. The device is quite economical; one full cartridge is enough for approximately 200 scanned sheets for black and white printing and half as many color images.

Our advice to you: if you plan to constantly replenish ink yourself without buying new cartridges, then take a Canon brand model. They are reliable and at the same time print great.

Cartridges for inkjet printers come in two types: with a built-in print head and without it. The type of cartridge that does not have a print head is usually used in models Epson printers. Printhead cartridges are used in HP and Canon printers and can be refilled. It is impossible to list the types of cartridges that can be refilled due to their diversity; for example, we can name the HP cartridge 22, 21, 122, 121, 135, 901, Canon 503, 510, 511, 40, 41, 37, 38.

This cartridge is a plastic hopper filled with foam impregnated with ink. Upper part The cartridge has a system of strokes to allow air to escape and equalize the pressure inside the ink reservoir. Through the nozzles, microscopic droplets of ink evaporate and display a given point on the paper. The color cartridge has three compartments for different inks.

The process of refilling such cartridges is to make a hole and pump ink through it into the foam. In this case, they do not remove the top sticker, but simply make holes. The sticker on the cartridge serves as protection for the ventilation ducts. After filling, seal the hole with a small piece of tape, or drop a drop of epoxy resin on top. There are three reservoirs in a color cartridge with ink of different colors. In order not to confuse the color, you need to draw a mark with the nozzles on a white napkin, then it will become clear where to refill which ink.

Refilling cartridges is also not universal solution problems, but only temporary. The foam that fills the ink reservoir loses its elasticity over time and is saturated unevenly, so the ink sensor in the cartridge begins to show the ink level incorrectly, and all the time gives warning messages that the ink has run out.

Refilling cartridges at the service center TRIKART is carried out through the nozzle area, and in a vacuum, so the pressure inside is not disturbed, and the ink flows evenly. We, when refilling at home, cannot comply with these rules, because air bubbles remain in some cavities, pressure is created incorrectly, something like a vacuum, and the ink “does not want” to come out, the cartridge may not print for some time after refilling . Ink pumping, which is controlled using special printer maintenance programs, helps.

It should be noted that using inkjet printer will not work from case to case, it is designed in such a way that during breaks in work consumables will fall into disrepair. Because the print head will simply dry out without work, the distance in the nozzles is so small. And if the head is located directly in the printer, then the printer will become unusable, because replacing the head at a price is comparable to the price of a new printer, and you often won’t find the spare parts you need.

In some cases, it is possible to revive a dried cartridge by soaking it in a special composition, or simply in water. The cartridge is placed in the liquid with nozzles and kept for several days, then wiped dry. You can hold the dried cartridge over steam, sometimes this helps. But most often in this case you have to buy a new cartridge.

In providing services to the population, individual entrepreneurs and other organizations for refueling, repairs and restoration, namely laser cartridges, as well as in other areas that contribute to favorable living conditions, there are trends, namely, tricks, nuances and improved techniques aimed by gas station operators, first of all, to make their work easier: saving time and reducing the cost of the service itself.

For people who are very far from refilling and restoring cartridges, many of the techniques and tricks may be very surprised, discouraged, or simply angry.

An experienced cartridge refiller, just by holding the cartridge in his hands, without any scales, will accurately determine the toner volume of the cartridge in grams. And a professional cartridge refiller, through whose hands tens, and maybe hundreds of thousands of cartridges have passed, will, only after examining a cartridge in need of repair, with a high degree of probability tell you which parts need to be replaced with new ones, and exactly how much, and at what cost, the cartridge will need to be repaired. Cruel life practice has proven that everything simple is brilliant.

Now let’s look at 9 Ingenious deceptions when refilling cartridges:

Refill with cheaper toner.
Scam for restoring (buying a new) cartridge.
Lack of promised cartridge cleaning.
Install used parts and pass them off as new.
Cause the lack of a guarantee for the work performed due to the lack of testing equipment (printers)
Cartridge repair according to double standards with a difference in price.
Refilling the cartridge according to a double standard with a difference in the price category.
Lack of cartridge refilling as such.
No repair or restoration of the cartridge as such.

First way: Probably one of the most popular and widespread. When a cartridge refiller or manager promises to refill with high-quality and branded toner, but in fact the refilling process is carried out with low-quality and budget toner powder.

Method number two: A categorical statement from a service worker about the complete malfunction of the cartridge, sometimes original and expensive, with a one-time offer to purchase a cheap compatible cartridge. Although it is true that original cartridge best restored and will last a very long time.

Third way: Failure to fulfill a promise to clean the cartridge. Although this should be done by default. After all, the process of refilling a cartridge with toner a priori implies complete cleaning: from residues from previous refills and waste toner due to use.

Method number four: The installation is really original spare parts, but, alas, have already lost from 30 to 50 percent of their properties.

Fifth way:“We simply refilled your cartridge and added toner. The cartridge is full." These are the explanations of the service manager or cartridge refilling technician after customer complaints about poor-quality printing. Motivated by the lack of testing equipment. In any case, there should be a guarantee for the work performed. Alternatively, the client can, and even needs to, bring his own printer to check the print quality of the cartridge.

Sixth method: As one of the common types of deception methods number 2. When only one of the cartridge parts is actually worn out, which renders the entire printed document unusable, and the service engineer insists and confirms to the client that for high-quality printing, replacement of all cartridge parts is required.

Seventh method: One of the variations of method number 1. When a refilling technician, having assessed the condition and quality of the cartridge parts, suggests refilling it with one or another toner powder to improve print quality. Accordingly, the higher the price, the supposedly better and higher quality the toner. To be more convincing, the client is offered a choice of about 3 or more toner options, in different price categories. But even here there is a nuance. If the cartridge is worn out, which is called trash, it is refilled with budget toner, but with, say, a very powerful magnetic component. The client does not have money for repairs, but wants good quality. In Okontsovo he will receive acceptable quality. But the parts of the cartridge will go to another world, giving up their last resources, which were squeezed out by this powerful and budget toner. By the way, at an inflated price - the client himself wanted to get good quality printing without repair costs.

Eighth method: The fastest. An experienced refiller will instantly determine by weight that the cartridge is full, or even that it is completely empty. There are only two options here. In the first case, in response to the client’s complaints about dull and faded printing, there will be a call to fork out for a replacement drum. In the second case, it is supposedly refilling, without adding toner as such, just cleaning the parts.

Method number nine: Most likely, the most sophisticated and combined. When at the cost of a complete repair or full recovery the cartridge lies standard procedure refilling with high-quality toner or banal cleaning of components, or replacing just one part of the laser cartridge.