• I can't connect the printer via local network. Connecting and setting up the printer for a local network

    How to connect correctly and quickly printer to a computer is perhaps the most common question for novice users. And, if, a simple connection printer and a computer with wires, in fact, is not difficult (it is important to find suitable connectors), then the further stages of installation printer may confuse the user. Below are the basic rules for installing and managing parameters printer in the Windows operating system.

    Printer is one of the main information output devices. Depending on the computer configuration, the following connection options are possible: printer:
    - local printer, connected to an LPT port or USB bus;
    - network printer or printer connected to another computer.
    After deciding which printer will be used on a personal computer, it is necessary to install it, i.e. install firmware that will convert into understandable printer type text and pictures. After all printer It doesn't print letters, just dots. And how often the dots are applied to the paper conveys the saturation of the image. So, if you apply a large number of dots on paper without any gaps, you will see that you get a monochromatic figure filled with one color. If printer black and white(otherwise called monochrome), then this fill will be black or gray.
    When installing local printer You need to connect the switched off device to the computer and then turn on the power. If the printer is plug and play, the operating system will automatically recognize the new device and install required driver. If the device does not support plug and play technology, then you must install the driver manually.
    When installing local printer With plug and play support, follow these steps:
    1. Connect printer
    2. Plug the printer power cord into electrical outlet and turn on the printer. Windows detects the printer Plug and Play and in many cases installs it without user interaction. Printer ready to print.
    3. When the Find New Hardware Wizard appears, make sure that the option Automatic installation(recommended), click Next and follow the instructions.

    To connect to printer does not support Plug and Play, follow these steps:
    1. Connect printer to the appropriate computer port according to the computer manufacturer's instructions.
    2. Plug in the power cord printer into an electrical outlet and turn on printer.
    3. Open the Printers and Faxes component of the operating system through the Start menu (the button in the lower left corner of the screen).
    4. In the Printing Tasks group, click the Installation link printer printer
    5. Set the Local switch printer, clear the Automatically detect and install Plug and Play printer check box, and then click Next.
    6. Most computers use to send data to printer, directly connected to the computer, parallel port (LPT1). Therefore, in the Use Port box, select LPT1: (Recommended Printer Port), and then click Next. However, some plotters can be connected to a computer through one of the serial ports (COM). When connecting such plotter select one of the serial ports (COM).
    7. Follow the instructions that appear on the screen.
    Once installation is complete, the printer icon will appear in the " Printers and faxes" If you need to print a test page, make sure that printer turned on and ready to print.

    When installing the network printer best:
    - run the installation wizard printer;

    Select network printer;

    Specify printer or select printer from those found on the Internet;
    - choose a manufacturer printer and model;
    - set a name printer;
    - set name printer for network users to access it.
    After the task general characteristics printer you can assign it some device-dependent parameters: fonts, memory size printer, possibility of color printing, etc.

    Please note that you can assign printer default device. In this case, all documents when sent for printing will be sent to this printer, unless you choose another one.

    How to install printer with creating a local port:
    1. Open the component Printers and faxes.
    printer to start the installation wizard printer, and then click Next.
    3. Set the Local switch printer, uncheck Automatically detect and install printer Plug and Play and click Next.
    4. Select the Create a new port radio button, the port type is Local port, and click Next.
    5. Enter a port name and click OK.
    6. Finish adding printer Using the Add Printer Wizard, following the on-screen instructions.

    How to install network printer connected to another computer:
    First, before you connect to printer which is connected to another computer,
    you need to make sure that printer has general access.
    1. Open the component Printers and faxes.
    2. In the Printing Tasks group, click the Installation link printer to start the installation wizard printer, and then click Next.
    3. Select an option: Network or connected to another computer printer and click Next.
    4. Connect to the right one printer via review printers, name indication printer or specifying the IP address printer(For experienced users).
    5. To complete the connection to printer, follow the instructions that appear on the screen.
    Connected icon printer will appear in the folder Printers and faxes.

    Set properties printer you can by opening the component Printers and faxes. Right click printer, whose settings you want to change, and select Properties.
    Review all tabs and make any necessary changes.

    Properties printer include many categories of parameters, including those related to print quality printer, shared access to printer, selecting the access mode printer over the network for other users, printing a test page, etc.

    If the computer has already come into every home and has become commonplace, then printers are still more common for office workers. Therefore, let me give in this article another printing solution that is relevant for home users who have not yet purchased a printer. It is possible to install a program on your computer that can convert most files into pdf format. This way you can easily imagine what the document will look like or send it by mail in a form that cannot be changed. One of these programs is PrimoPDF, the other is pdf-24.

    How to allow all users to print from the same printer.

    Let's start with the fact that modern printers, MFPs and other devices differ in the type of connection to the PC. The most popular and widespread are LPT (although this port is already going out of fashion), USB, and Ethernet ports. Accordingly, setting up a printer on a personal computer will vary depending on which port you use. All ports have their pros and cons. Well, for example, if through usb connection printing, one might say, is “instant”, but printing over the network may take some time, because documents vary in size and until they are transmitted over the network to the printer, printing will not start... besides, if the printer is connected via usb, if the server PC (the PC on which the printer is installed) breaks down, the printer will not be available to any user.

    So let's get started. Let's look at two examples of setting up devices on Windows 7.

    USB connection

    Let's say a printer is installed on your computer and connected via a USB cable, how can you make it so that other users can print on it?

    We need to proceed to " Start" - "Devices and Printers":

    The window that appears will display all installed printers, faxes, monitors, scanners, MFPs, and so on:

    But we need to select the printer that should be shared. Right-click on the desired printer (in my case it is HP LaserJet 400 MFP M425 PCL 6). In the pop-up window, click on " Printer property":

    What we see here is an inactive item " Share this printer". It is necessary to check this box. Such manipulations will now allow us to find the printer by IP address or DNS computer name. But do not rush to click " OK", you should also check the box with the name " Add to Active Directory "(If you have a domain machine, this will simplify the search for a printer, and you can find out how below in the article):


    Before clicking the " OK", let's make the final settings. Click on the button " Additional drivers...":


    In the window Additional drivers"You must check all the boxes (provided that drivers for x86, x64, etc. devices are installed). This will allow you to install printer drivers over the network not only for 32-bit PCs, but also for 64-bit ones:


    All! Now you can press " OK" in this and the previous window. The sharing setup is complete. Now let's look at how to connect to our printer from another PC. To do this, you need to go to the " window on another PC. Devices and Printers" and click on the link " Installing the Printer":


    In the window that appears, we will see two items: " Add a local printer" And "":


    To connect the printer by IP address, select the first item; to connect the printer via Active Directory, select the second item. Let's first select the first item, click on it and go to " Select printer port":


    Select " Create a new port", V " Port type"choose" Standard TCP/IP Port"either" Local Port" and press " Next":


    In the menu " Enter the printer name or IP address"you must specify the IP address of the computer on which the printer is installed (in my case it is 10.81.0.50), click " Next", after which the installation of the printer should begin. Once the installation is complete, you can start printing.


    So, now let's go back a few steps and look at an example of adding a printer through Active Directory. Select the item " Add a network, wireless or Bluetooth printer":


    In the menu " Search for available printers..", without waiting for the search, we immediately click the link " The printer you need is not in the list":


    In the menu that appears, we see three installation options, you can select any of them. In the first paragraph you can find the printer through Active Directory, in the second paragraph you can find it by entering the computer name or by finding a computer on the network, in the third paragraph you can specify the IP address. Select the first item and press " Next"and we get a window" Search: Printers":



    Here you will see a list of all available printers on the domain network, and you can also filter them by parameters. The screenshot shows that I selected my printer, which I shared earlier, just click on it to begin its installation, after which you can use the printer.

    Ethernet connection

    I will show an example of such a connection on a printer, or rather Canon MFP i-Sensys 411 dw. For other manufacturers and on other models, the actions will be identical. Before connecting directly to the printer over the network, you need to configure its IP address on the printer itself! This is important, otherwise we simply will not find the printer on the network.

    On touch display printer, click on " Menu":


    Select " Network setup":


    Select " TCP/IP Settings":


    Select " IPv4 settings":


    Select " IP address settings":


    In this menu, you can get the settings automatically, but as experience shows, the printer cannot grab a DHCP server, in short, IP addresses are not automatically assigned to the printer correctly, it is better to enter them manually. Select " Receive manually":


    Enter the IP address and subnet mask. All these parameters depend on your network; the address in the photo is shown as an example. When the address and subnet mask are entered, press " Apply" and we can move to our computer to connect the printer.


    After setting up the printer, you need to download the driver from the official website, in my case the driver was downloaded " MF410MFDriverV2160W64RU". Unpack and run:



    In the next window we will find the printer if automatic search didn't help, enter the printer's IP address and click " Next":


    That's all! The printer will install and you can print documents. I hope this article will help you in setting up your printer! Good luck!

    A computer local network consists of several PCs located close to each other. Such an association is built through wired and wireless technologies. Technical features vary depending on routing, administration type, and topology. The simplest local network is considered to be a direct (point-to-point) connection of two computers. For such a connection, standard topologies are used.

    Users of PCs connected to the same local network can share equipment, in particular a printer. You need to connect your computer to the printer via local network.

    What will we talk about:

    Connection via PC

    The need for such a combination often arises in offices where, due to lack of finance or simply space, there is one printer for several computers. Similar mode work is fraught with some problems. After all, only the employee to whose PC the equipment is connected can fully use the printer, while everyone else is forced to wait their turn with flash cards in their hands.

    Quick printing of required documents makes the work process as streamlined as possible. Today, there are several ways to connect a printer via a local network.

    First you need to make some changes to the settings on the main PC. It is necessary to understand that the computer to which the printer will be connected must have the appropriate characteristics. This is due to the fact that he must be in working mode throughout the working day without freezing. Otherwise, you won't be able to print anything.

    1. First you need to set up your local network.
    2. We connect peripheral equipment to the PC using a USB cable.
    3. Installing drivers for the printer.
    4. Print out the page for testing.

    We provide all PCs with shared access to the connected printer

    Go to the “Control Panel”, open the “Network and Internet” tab, then “Network and Sharing Center”. The last step is to open the sharing options. A tab with this name is present in the list that appears.

    In order to connect the printer locally Windows network 7 You also need to use the “Disable password protected sharing” function. The last step is to save the changed settings.

    Connecting “Sharing” on PC

    Again, the “Control Panel” menu, the “Network and Internet” tab, “ Home group" You also need to go to the section dedicated to printers and devices, where we first select and then confirm “Sharing”.

    Allowing access

    To do this, go to the “Control Panel” menu, then you will need a tab called “Hardware and Sound”. In it, select “Devices and Printers”, on desired device Click to open the dialog box and click “Access”.

    Then we confirm our permission and assign a new name to the printer. This will greatly facilitate subsequent setup. The equipment after these manipulations can be considered network.

    The printer installation takes place in automatic mode, since all drivers are found by the OS (Windows 7, Windows XP, Windows 10), otherwise they are loaded from special disks. Fixing the "Default Device" setting makes the printing process easier because you only have to select a printer once.

    If a mistake occurs and the new name does not appear, you should add it manually.

    Opening:

    • "Control Panel";
    • "Equipment and Sound";
    • "Devices and Printers"

    At this stage, click on the “Add a Printer” tab.

    To connect a printer via a Windows 10 local network, you can use search. The program will display its results, and if the device is detected, click “Next”. The same applies to the operating room Windows systems 8.

    If Windows 7 (Windows XP) is installed on the PC, then the “Add a network printer” tab is used. In the event that a manual search does not end with the desired result, you will have to select the link called “The required printer is not in the list”, then “Select shared printer by name." All you have to do is click on “Review”.

    Then you see a list of PCs connected to the local network. Of these, you must select the one to which the peripheral device is connected via a USB port. After discovering it, you just need to follow the recommendations of the wizard. A similar program is available in Windows 10, Windows 7, Windows XP and other operating systems.

    Connection via router (router)

    A router is a device for accessing the Internet, a kind of intermediary between the client and the provider. Example in the photo. Its use makes the process safer and more convenient. The router is used in networks various types, including segmented local ones. It also provides traffic management and uninterrupted communication. Used in this case network protocols expand and complicate the network. The router uses network paths to transmit information.

    There are two types of devices: wired and wireless. The main criterion is the PC format. If the user has a laptop, then it will be much more convenient for him with a router that provides for the absence of wires.

    The printer is connected via a router so that it is accessible to all PCs on the existing local network. The process does not require special adapters and is suitable for Windows 10, Windows 7, Windows XP and any other OS; a USB interface will be required. Every printer has it.

    Therefore, you will need a router, a printer, and a cable to connect to the previous device. Also, we should not forget about the PCs that make up the local network.

    You should make sure that the router has a USB port and supports a printer. You need to connect the printer to the router. Both must be disconnected from the power supply.

    It is performed from each computer on the network by sequentially entering the following tabs:

    • "Start";
    • "Control Panel";
    • "Devices and Printers";
    • “Installing the printer”;
    • "Add a local printer."

    USB port is being configured

    The last step of the previous paragraph ends with a click on “Next”. Afterwards you need to select the “Create a new port” tab, as this causes a list to appear. The defining line in it is “Standard TCP/IP Port”. And again “Next”.

    Entering data

    Here you will need to enter the IP address of the router, as well as the word indicating the router. You should not remove the check mark from the “Poll the printer and select the driver automatically” line.

    Finding connected printing equipment

    If it turns out to be useless, then the next step is to sequentially enter:

    • "Device type";
    • "Special";
    • "Options"

    Those fields that were filled in earlier should remain unchanged, just like the “Protocol” line (its value is RAW) and Port No. (9100). After clicking on “Ok” and upon returning “Next”. The last step will be to write the brand of the manufacturer of the connected printer.

    Completing setup

    This is indicated by a notification that the installation has been successfully completed. It also becomes possible to check the operation of the printer through the router over the entire local network.

    The setup, the process of which is described above, must occur on each computer included in the local network. This method of connecting the printer has several important advantages. It does not require PC operation, therefore it does not waste a large amount of electricity. Starting up the router does not take much time, and its operation is not accompanied by noise.

    It is common practice in the office and at home to share various peripheral devices, such as scanners or printers, on the network. This is convenient - you can immediately print any document and do not need to drag files on a flash drive from computer to computer or buy for each workplace separate printer. How to properly configure the equipment for sharing we will tell you in this article.

    Network printing

    Printing over the network is a common thing, now you won’t surprise anyone with it. However, printer sharing is still often configured according to this scheme. The printer is connected to one of the computers and is accessible to other users who can directly print their documents. Everything is simple, you don’t need to be fancy with the settings. But, in fact, it is not always convenient. The best way to connect a network printer is to connect through a router.

    Advantage

    The main inconvenience of the scheme described above is the binding of the printer to a specific computer. This computer must be turned on for network printing to work. What if the employee who works for him got sick and did not come to work, and access to the computer is password protected? Or has the computer failed?

    Therefore, it is much more convenient when the printer is connected to the router and is always available. But there are nuances here.

    Print server

    In order for the printer to work independently on the network without connecting to a computer, a print server is needed. The print server can be software built into the router or printer. Routers equipped with a USB port usually support network printing. However, just in case, it is recommended to check technical documentation. If your router has a USB port, but does not have a print server, you will not be able to connect a printer to it.

    The printer may have its own built-in print server. These printers are equipped with a LAN port for connecting a network cable or wireless Wi-Fi-module.

    If your router does not have a built-in print server and you have an ordinary printer, you will need hardware print server – separate device with a USB port for connecting a printer and a network connector, through which the device is connected to the LAN port of the router using a patch cord.

    Types of connection

    Before setting up a network printer via a router, let's deal with possible options connections. So, You can connect the printer to the router in the following ways:

    • Via USB port. This connection is possible if your device supports network printing.
    • Via LAN port. If your printer is equipped with a built-in print server with a network port, you can connect it to the router using a patch cord.
    • Via Wi-Fi. Some modern printers are equipped with a Wi-Fi module and can communicate with the router over the air. You can also connect to them directly from a laptop equipped with a Wi-Fi module.
    • Using a hardware print server. This is a separate device to which the printer is connected. The print server has a LAN port for connecting to the router.

    USB connection

    Connect your printer to the router's USB port using a cable. Both devices must be turned off. Then turn on the router and wait for it to boot. After this, you can turn on the printer. By default, the router does not need any special configuration; it should immediately recognize the printing device. You can check this by logging into the device’s web interface and opening the network map. Your printer model should be displayed there. If this does not happen, check the status of the print server. It must be online.

    Wi-Fi connection

    If your printer is equipped with a wireless Wi-Fi module, then you can connect it to the router over the air without any wires. You can do this in two ways:

    • WPS. In the instructions for your printer we find how to activate the WPS function. Then click on the router. We wait until the connection is established (the indicator on the router stops blinking) and check whether your printer appears on the network map.
    • WEP/WPA. Manual setting is similar to setting up the first connection to a wireless network of any Wi-Fi device. We find the network settings in the printer menu, select the network we need and enter the username and password.

    Connection via LAN port

    If you find yourself happy owner printer with a network port, you can connect it to the router via LAN using a regular patch cord. The cable is usually included. If you don’t have it, you can use the patch cord from the router if you don’t have one. Or buy a cable of suitable length in a store.

    In the device menu you need to set it to a static IP address. It is advisable to do this even if your router is configured. The fact is that if the printer’s IP address constantly changes, this will complicate its search and it will periodically disappear from the list available devices. There is, of course, the option to reserve an IP address in the DHCP server settings by MAC address.

    After this, the printer will reboot. After which it can be found in the list network devices.

    Install the printer drivers and print a test page.

    Using a hardware print server

    If your printer is not equipped with a network card or Wi-Fi module, and your router is not equipped with a USB port, you can purchase a hardware print server. As mentioned above, this is a separate device that acts as an intermediary between the router and the printer.

    Budget models have one USB port and network port. More expensive ones - several USB, and also, optionally, an LPT port. Also, the print server can have a built-in Wi-Fi module and connect to the router not via cable, but over the air.

    First, we connect the print server to the router, and the printer to the print server.

    The print server is configured using the supplied proprietary utility. It allows you to find a print server on the network and set an IP address for it. Further configuration is carried out via the web interface according to the instructions. You can enter it by entering address bar IP browser that was installed for the print server during initial configuration.

    As you can see, there are several ways to connect your network printer to your router, depending on its hardware capabilities.

    Setting up your computer

    Regardless of which of the methods described above you choose, the settings on the computer are performed the same in all cases.

    You can configure it through the “Control Panel” or through “Printers and Scanners”. The setup is similar.

    "Printers and Scanners" appeared on the latest Windows versions. This application is suitable for setting up a network printer on Windows 10.

    We will configure it through the “Control Panel”, which is available on all versions of Windows. In particular, it is suitable for setting up a network printer on Windows 7.

    Search for “Control Panel” in your computer search. In the Control Panel we find the “Devices and Printers” section. Click on the “Add a printer” item.

    The system will try to find the device connected to the computer, but, of course, it will not succeed. Therefore, we will use the item “The required printer is not in the list” at the bottom of the window.

    On next page select the item to add by TCP/IP address or host name. Click “Next”.

    In the next window, in the “Device Type” drop-down list, select “TCP/IP Device”, and below in the “IP Address” and “Port Name” fields enter the address that we get as follows:

    • When the printing device is connected via USB to the router, enter the IP address of your router, which you enter in the browser to enter the web interface. This is usually 192.168.0.1 or 192.168.1.1. It is indicated on the label at the bottom of the device.
    • When connecting via a LAN port with an address specified through the menu. In this case, enter this address.
    • If the printing device is connected via LAN and receives an IP address from a DHCP server, look.

    It is better to uncheck the checkbox for asking and selecting a driver automatically.

    In the next window, check the “Special” box and click the “Options” button next to it.

    In the settings window that opens, select the LPR protocol, and in the “Queue name” field - in our example we wrote “naseti”, in fact, any name can be written. Click OK and return to the previous page.

    You can give the printer a new name, or you can leave the default one.

    We refuse the offer to allow shared access to the printer and click “Next” again.

    A message should appear here stating that everything went well and the printer is ready for use. To verify this, print a test page.

    Setting up a print server on the router

    If you have any difficulties, you can use the utility to configure the print server on the router. You can download it from the manufacturer’s official website by selecting your router model in the “Downloads” section.

    To configure the print server on TP-link routers the proprietary TP-Link UDS Printer Controller utility is used. After you have downloaded and installed the program on your computer, run it and it will automatically find all printers connected to the router. Select the one you want to use to connect automatically.

    The utility works with Windows and Mac OS.

    For D-Link routers use proprietary utility SIUtility. If you have a router from another manufacturer, look for compatible software on the official website.

    Instructions

    Connect the LAN (Ethernet) port of the router to the printer using a network cable. The last device, in turn, connect to the computer. To do this, use an adapter cable with USB port to the USB-B port (square connector).

    In this situation, you cannot use the printer yet. First, install on all computers from which you plan to use this network equipment, drivers for specific model printer.

    Set this equipment to a static (permanent) IP address. It is recommended to use the addresses of the zone in which other computers and laptops are located. Those. Only the fourth segments should be different in all IP addresses on the network. When this function is activated, the printer will have a permanent IP address even if it is enabled in the router settings DHCP function.

    Video on the topic

    Please note

    The option of connecting a printer to a router is much more convenient, because the availability of this equipment does not depend on any specific computer.

    Useful advice

    The fact is that most routers have the function of automatically issuing IP addresses. IN in this case it is very annoying because every time you turn on the printer it will receive a new IP address. This will make it very difficult quick access to this equipment.

    If you work in an office or need to connect to a printer with different computers at the same time, then the question of connecting a network printer is now more relevant for you than ever before. By connecting your printer to the network, you will make your work much easier, because constantly switching the printer's USB cable wastes time.

    You will need

    • Computer, printer, connecting cables.

    Instructions

    Click the Start menu - Printers and Faxes. You can also view the window with installed printers as follows: “Start” menu - “Control Panel” - “Printers and Faxes”. In the window that opens, select “Add a printer.”

    In the window that opens, select “Add a printer.”

    In the Add Printer Wizard, click Next.

    If the printer name is unknown, then leave the line with the printer name empty and click “Next”.

    Please note

    If the operating system does not detect the printer you are looking for, then most likely the printer is de-energized. Plug it in and try connecting it to the network again.

    Useful advice

    When connecting a printer to a network, it is advisable to make it the default printer. This will allow you to type quickly required material, because you waste time choosing a printer.

    Sources:

    You will need

    • router;
    • computers;
    • network cables.

    Instructions

    First of all, connect all the cables necessary for work. There are several inputs for cables - one of them is the main one, which is usually marked WAN. Connect the cable provided by your Internet service provider to this input.

    Connect the cables of the computers you want to connect to the network to the remaining free inputs. To connect, use cables with a regular crimp pattern.

    Now make the necessary settings. In most cases, this setup has to be done manually; most likely, you will encounter the same situation. Don’t be alarmed, manual router operation is not as scary as it seems at first glance.

    After this, you will be asked for your login and . Enter the default login and password (admin/admin). After this, enter the settings menu, where you will make the main settings.

    Now we need to select the operating mode of the router. The router has several modes:
    Bridge – in this mode, information passes through itself, but the settings will need to be set separately on each. The Access Point mode has the same properties.
    NAT is an address translation mode, with its help all computers on the network will be perceived external sources like one computer with one address. Within the network, each computer receives a separate address from this system. The advantage of this system is that many providers limit the number of computers included in the local network, and with the help of such a system you can mask the number of computers, since they will all have the same address.
    DHCP - this mode allows the router to automatically connect to all computers on the network. It is most convenient if there are a lot of computers connected to the network, since in this case it will be problematic to configure each one

    After selecting the router operating mode, you need to configure WAN and LAN. LAN is a local network, and WAN is an external network. As a rule, there is nothing complicated in their settings.

    If your router has wireless interface, then you can also configure Wi-Fi.
    Enjoy your work!

    Video on the topic

    Please note

    The “firmware” must be saved on the computer to which the router will be connected, and then unzipped if it is archived. 2. Setting up your computer. In order to set up a Wi-Fi router, you need to configure the computer from which you access the Internet - determine the protocol and type of connection to the provider.

    Useful advice

    How to set up Router D-Link? Setting up a VPN router on D-Link example DI-524. First, you need to connect the router to the electrical network and connect, using the cable supplied, one of the internal ports of the router (LAN interface) with the network card on the computer from which the setup will be done.

    Sources:

    • how to configure the router

    Wi-Fi networks and others wireless methods data transmissions are gradually replacing the one we all love so much wired internet. This is not surprising, because laptops are becoming more and more popular, and therefore, the need to run a cable across the entire apartment simply disappears. Unfortunately, not everyone can set up a wireless network at home, much less select the equipment necessary for these purposes. The most important elements in this system is precisely router. Without this small but extremely necessary thing, it will be very difficult to create a high-quality wireless network.

    Instructions

    It is difficult to determine the main criterion Wi-Fi selection A. It all depends on whether you will connect only laptops, or whether your plans also include wired computers. Based on this, choose router with the required number of LAN ports. This is very important, because if there are not enough ports, you will have to purchase an additional switch.

    Once you have decided on the number of LAN ports, it's time to start considering the Wi-Fi channel. Due to the fact that these systems are still being actively developed, there are several leading types of encryption and transmission of Wi-Fi data. This may be the familiar 802.11 with the addition of “n” or “g”. Please note that "g" is more than "n". Those. if yours only supports 802.11g channel, it is not worth purchasing router with channel type 802.11n, because Compatibility issues may arise. Among the encryption options, WPA2-PSK is the leader, but you can safely router, which only supports WPA. You should not purchase a device that works exclusively with WEP encryption.

    Sources:

    • how to choose a router for your home

    In our country, the overwhelming majority of offices are small. They contain several computers and one or two printer. There is no dedicated server and is not planned in the future. The role of the file exchanger is played by the most powerful computer of all available. Your task is to set up this entire network and computers so that everyone can print from this printer.

    Instructions

    Install software that allows you to fine tuning printer operating mode. Run it and set a static IP address for this equipment. It is advisable to use an IP that will differ in the last segment from the addresses of other network devices.

    Now physically disconnect the printer from the computer. Open the Start menu and go to the Devices and printers" Click the Add a Printer button and select the Add a Local Printer option. Select the port type and click Next. Install the required driver and connect the printer to this computer.

    To avoid paying your provider for creating several access points to connect computers to the Internet, use a connection via router(router). General settings router but almost the same for all models.

    Instructions

    Buy router the model you need, taking into account whether you want it to have a Wi-Fi wireless interface (which is convenient for connecting laptops) or not. However, you can buy along with the usual router ohm and a separate Wi-Fi module (in the form of a USB module or PCI card). If you don’t need it, the usual one will be enough for you. router and with several LAN ports.

    Find on router e WAN port and connect a cable to it that provides an Internet connection. Connect one of the computers and router to the electrical network.

    Set up an access point in router e. Enter the IP address in the browser router and (for example, 192.168.1.1), enter the factory login and password. By default, both login and password will be “admin” (don’t forget to change them later). Entering settings router a, set the settings recommended by your provider, while keeping in mind: - the type of data transfer must match the one used by your provider; - access password router y after replacement should be quite complex; - IP address computer must be different from the IP address router a; - setting a static and dynamic IP address on router must be agreed with the provider and comply with the manufacturer's recommendations.

    Reboot router after setup. Check whether the computer connected to it has access to the Internet. Connect to router on the second computer, using a different IP address, registering this route on router. Please note: the mask must be the same.

    If you router and you have a Wi-Fi wireless interface or you bought a separate adapter (for which you will need to first install drivers and software), you can connect two computer each other and in this way.

    Check if it is active Wi-Fi module on the second computer. If not, right-click on its icon in the taskbar and select "Connect". Check if the Internet connection is available on the second computer.

    Modern printers and MFPs, unlike older analogues, are adapted to connect to laptops and other types of mobile computers. To configure printing devices, you must use additional utilities or tools operating systems.

    You will need

    • - printer;
    • - USB cable - USB B;
    • - driver files.

    Instructions

    Connect the printer to your desktop or mobile computer. To carry out this process, you will need a USB-USB B cable. Turn on your computer and printing device. Wait for the hardware to finish loading.

    Install the appropriate drivers for your printer model. Best to use special program, which allows you to change operating parameters printing device.

    If after implementation this process the printer was not recognized by the system, add a new device yourself. Open the Start menu and go to Control Panel.

    Click on the “Printers and other devices” icon. In the new menu, select the “Printers and Faxes” sub-item. Now left click on the icon the desired printer. In this case, you must be guided by the model name of the printing device. Follow the "Device Installation" link.

    In the first dialog box, select the printer access type. If you wish to use this equipment only with of this computer, indicate the option " Local printer" Click the "Next" button.

    In the next window, select the port through which you connected the printer. It is important to note that you only need to specify the port type (USB), and not select a specific slot number. Wait a while until the device is detected by the system.

    Close the Add Printer Wizard. Open the program that you installed along with the drivers. Configure the operating parameters of the printing device. To do this, select the paint consumption mode, activate required modes print and specify the page orientation (portrait or landscape).

    If you are using custom printing paper, be sure to specify the type. This will improve the quality of the printer.

    Tip 9: What devices can be connected to the router

    Today, both in the home and in the office, a data transmission technology called Ethernet has become widespread. Although initially it was developed in relation only to computers, with the advent of new technology Wi-Fi has become possible connection and others digital devices. In addition to PCs and laptops, the router can connect smartphones, gaming equipment and technology.

    Instructions

    Since the mid-1990s, with the growth of broadband Internet access, equipping computers and laptops with routers () has become widespread. The router establishes an internal network in your home or office and serves " " to the Internet, giving you access to email, web pages and other resources. The router connects to the PC using network card, which transforms data on the network. The router assigns each of your PCs an Internet Protocol address, an identifier that allows connecting machines to send and receive information to each other.

    Majority modern smartphones and tablet PCs are pre-equipped with Wi-Fi technology, making them suitable for use in home and public networks. To connect such devices to the router, use special utility. When you see your own network in the list, select it and enter your router password.

    Many home entertainment devices, such as Blu-ray and set-top, are equipped with Wi-Fi, giving devices access to services such as gaming sites, Pandora and Netflix. Router-compatible entertainment devices include Roku, Apple TV and Xbox. Connecting them to the network is similar to mobile devices: select the list available networks Wi-Fi, sign in.

    Laser printers have long supported Ethernet connections; More recently, Wi-Fi enabled inkjet models have become available for use at home and in the office. When connected to a router, multiple users can use these printers from desktop PCs, laptops or mobile devices. Later versions support both wired and wireless connections.

    In recent years, refrigerators, washing machines, dryers and other household appliances have also been equipped with Wi-Fi technology. Using a router, they receive an IP address and become part of the local network.

    Video on the topic

    One of the key stages of creating a home or office computer network is installation and configuration a. If you follow the instructions included with this device, the entire job can be completed fairly quickly.

    Instructions

    The router is designed to distribute the signal between fragments of a computer network or individual computers. Connect one end of the network cable to the modem and the other to one of the router's connectors. The name of the connector (WLAN, WAN, etc.) depends on the specific model. Make sure both the modem and router are connected to power. Some router models come with a disk with a special software, which is installed on the computer. If there is such a disk, install the programs available on it; they are designed to configure the device.

    Establish a connection between your computer and router. If this is your first time making such a connection, use Ethernet cable, so you can set up a wireless network. To connect use network cable, one end of which is connected to the Ethernet connector of the computer, and the other to one of the router ports marked 1, 2, 3, 4, etc.

    Open your browser and enter the router's IP address in the program's address bar. As a result, a page with the router settings will open. Enter your login and password to access the settings; they should be specified in the documentation for the device. The IP address depends on the device manufacturer, for example:

    D-Link - 192.168.0.1
    Linksys - 192.168.1.1
    Netgear - 192.168.0.1
    3Com - 192.168.1.1
    Belkin - 192.168.2.1

    In some cases, the router address is indicated on the packaging box or instructions. If it is not listed anywhere, visit the manufacturer’s official website and use the support service.

    Setting up an Internet connection is usually done automatically. The router receives all the necessary parameters from the modem. To configure Wi-Fi connections go to settings section wireless connection. Find the SSID field and enter a custom network name in it, make sure the Enable SSID Broadcast checkbox is checked. The remaining parameters can be left unchanged.

    To connect to the network you created, the user will need to enter a password on their device. To protect the connection, come up with complex password, consisting of an arbitrary sequence of letters and numbers. In addition, be sure to change your login and password to access the settings of the router itself, this will prevent unauthorized changes to the network settings.

    Video on the topic

    Router – universal device, intended for Internet distribution. The main advantage of this device is its versatility. A wide range of operation allows several gadgets to connect to the network at once. But before using for correct operation router required pre-setting.

    Instructions

    It is best to carry out the reconfiguration procedure by adjusting existing parameters. This will significantly reduce the time. To do this, connect the router using a cable to your personal computer, open a browser and enter the address: 192.168.1.1. That's how you get there. Immediately after entering this address, a window with two fields will appear. The first is for the login, the second is for the password. They should match each other, unless, of course, user changes were made. Try entering user or admin. One thing will certainly do. It all depends on the manufacturer's brand used.

    After entering the interface, visually analyze each function. Decide what exactly you need to reconfigure. If the connection parameters are lost, then go to the “Internet Settings” tab; if you change the wi-fi data, go to “Wireless Connection Settings”; if some sites are suddenly blocked, go to “Settings” parental controls" To change the firmware, open the most. Most often it is called “Parameters”. Click "Update" or download an existing one.

    You can completely reset all settings of the router in hardware mode, that is, through user interface, and mechanically by pressing Reset button from the back of the device. The dimensions of this button are very small, and you can press on it only with the help of some device, for example, a needle or a ballpoint pen. Some routers are not equipped with it, and you can reset it by pressing and holding the on/off button for a few seconds, usually ten to fifteen.

    Router management, click “Internet Settings”, enter the username and password specified in the agreement with your provider. Save the changes and restart your computer. This procedure will complete the reconfiguration of the router and establish communication with the Internet.

    - an integral part of office routine. This peripheral device has long become necessary equipment and for home use. To connect it, just follow the instructions and the service menu. If the equipment is working properly, the process should not cause problems.

    View options installed printer You can do this through the Start menu in the Control Panel tab. Find the "Printers and Faxes" menu item. Select your printer from the list of devices. Its designation must correspond to the name installed device. To check printing, right-click on the printer icon. In the window that opens, find the “Test Print” button.

    If there are several computers in the house connected to a local network, and a printer is connected to one of the PCs, the equipment can be configured to use a private local network on all PCs. Go to the Start menu on a computer that has a printer preinstalled. Select the "Printers and Faxes" or "Devices and Printers" tab. Find "Add a printer". The familiar Hardware Installation Wizard will open.

    Instructions

    In the modern world of scientific and technological progress, the Internet has become an integral part of reality, which is almost impossible to ignore. People turn to the World Wide Web to find an answer to a necessary question and to send an email. postal letter, viewing latest news And team game in virtual space. Everyone has their own reasons for accessing the Internet, but what to do if there is only one computer with access to the Internet, but there are many people who want to “go online” at once. For example, this typical situation is typical for work collectives or student groups, just at home or family members living together in an apartment or cottage.

    To solve the problem of providing simultaneous access to the network, you will need a router (router) capable of coordinating the joint work of several computer devices. Thus, a router is a device designed to connect network segments. Routers ensure the exchange of data between different network segments thanks to routing tables programmed into them. The tables contain information about the networks known to the router and the IP addresses to which packets need to be sent in order to get to these networks, as well as (information that allows the router to determine optimal route to the recipient). The routing table data is specified by the administrator or dynamically updated based on routing protocols.

    Externally, a regular router is a small box with a plastic case, which has a connector for connecting the Internet and many others for connecting computers. Today almost everything modern means connections such as cell phones, tablets and computers are equipped Wi-Fi receivers. Through a Wi-Fi connection, the listed devices can access both the Internet and other networks and devices without the use of wires. Therefore, take the first advice - choose a Wi-Fi router. This device will help you solve the problem of being tied to wires and give you freedom of movement without losing the connection. That is, you can connect to the network in any corner of your home or office.

    For selection suitable model router, you need to decide on the purposes for which the device is actually needed. After all, if you purchase a router that has the wrong connector or does not work with your provider, then, at best, you will have to return it to the store. Therefore, check with your provider about the ADSL or DSL connection type. Check your plan speed. And finally, decide how much coverage your router should provide.

    Video on the topic

    Read more: